Rethink Everything You Know About Workbenches

Поділитися
Вставка
  • Опубліковано 22 гру 2024

КОМЕНТАРІ • 259

  • @texasoldmantries
    @texasoldmantries 8 місяців тому +1

    I just finished making my bench today and it's a winner!!! Since I read all the discussion around the cross bracing I decided to plywood the entire back section. It won't move either way now. This is a great design!

  • @bowlerhatman01
    @bowlerhatman01 Рік тому +131

    Triangles are stronger than squares because the shape means that there is no possibility of pivoting at the corners. The only way for the angle at any corner of a triangle to change is by changing the length of any side. If you're building with rigid materials, that just can't happen without catastrophic failure. With any parallelogram, however, all sides can remain at the same length while also pivoting at each joint. When you whack a triangular brace on, you transform your parallelogram into two triangles.

    • @ThomasCustomWoodworks
      @ThomasCustomWoodworks  Рік тому +6

      Thank you!

    • @joejoe-lb6bw
      @joejoe-lb6bw Рік тому +13

      And if you add more triangles (kind of) you would be using a truss. Good explanation of trusses by Paul Kassabian, "How Trusses Work! (Structures 5-1)".

    • @DrJuan-ev8lu
      @DrJuan-ev8lu Рік тому +2

      Even better than a diagonal cross brace is a full panel of thin plywood.

    • @sergiomartinsdeoliveira2462
      @sergiomartinsdeoliveira2462 Рік тому

      😊😊😊😊😊😊😊

    • @Knate1104
      @Knate1104 10 місяців тому +6

      bowlerhatman01 is spot on. Triangles only have one degree of freedom. That means force is distributed equally to the sides of the triangle and no matter how much more force you apply, the triangle won’t change or deform (unless one of the sides is compromised). The result: extreme stability. It’s amazing to see how triangles are used in everyday construction and the loads they’re capable of bearing.

  • @davidaubin3449
    @davidaubin3449 Рік тому +16

    Fantastic work bench, I especially like you showing your mistakes and the fixes for them! Well done.

  • @tomblanar2592
    @tomblanar2592 Рік тому +13

    Very nice concept for a compact work surface. One change I would make if I built one would be to position the hinges so that the table surface when closed does not have a gap. It would only require a modification to the clearance made with the router and the gap would be gone. Nice job!

  • @tommanseau6277
    @tommanseau6277 Рік тому +6

    Diagonal bracing breaks up the force into separate components distributing the load. Lets say you're pushing horizontally across the work. WIthout the brace you can rack the bench because the force is still all horizontal. But the diagonal brace allows the force to be broken up and distributed between the horizontal, diagonal, and to a smaller extent, vertical directions. It's the same reason you see most bicycles are essentially 2 triangles or a lot of bridges are a series of triangles attached together.

  • @Henry-n7n8
    @Henry-n7n8 Рік тому +5

    really good looking work bench, I really like how you solved each problem, I learned from those problems.

  • @Bonjour-World
    @Bonjour-World 11 місяців тому +2

    The one problem most people fail to address is leveling the workbench (i.e. most garage floors are not flat or level). Putting 3/8 diameter leveling legs in the bottom of the legs is one solution but that requires a one to get down on their knees every time the workbench is re-positioned. There has to be a better solution but I have yet to see it (other than keeping a box of shims to put under the legs).

  • @oakfat5178
    @oakfat5178 9 місяців тому +1

    That was a joy to watch. Your design is very well thought out.

  • @llobj001
    @llobj001 Рік тому +4

    A cross brace will resist forces in both the X and Y plane. Really is that simple 👍🔥

  • @fotoeikenburg
    @fotoeikenburg 9 місяців тому

    Now this dubbeling those large clamps to fit the large tabletop board, that is fantastic! I should have known before… so weird I didn’t think of it for my former project, making large 7 feet sliding doors. I managed, however this would have made my day for sure! Thanks man. You’re a craftsman. Like!

  • @xplaur
    @xplaur 2 дні тому

    Awesome! I\m thinking of a piece of plywood instead of that diagonal.

  • @LoriLuker1
    @LoriLuker1 9 місяців тому

    Thank you so much for sharing. Hubby and I have been trying to figure out a plan and here you are. Being AMAZING! Thank you!

    • @ThomasCustomWoodworks
      @ThomasCustomWoodworks  9 місяців тому +1

      You’re welcome and thank you so much for the kind words!

    • @walidbeainy9043
      @walidbeainy9043 8 місяців тому

      Can you tell me the thickness and width of the boards you used. thanks in advance@@ThomasCustomWoodworks

  • @arainboldt
    @arainboldt 10 місяців тому

    @ThomasCustomWoodworks, thanks for the ideas! regarding the improved stability of the diagonal. It's due to the fact that the length of the hypotenuse is unique given the length of the sides and the degree of the opposite angle. Consequently, for any of these three to change, e.g. the degree of the opposite angle, the diagonal member (hypotenuse) must either lengthen or shorten. This can't happen without serious force. Conversely, in the case of a parallelogram or rectangle, the angles of the parallelogram/rectangle can change from near 0 to near 180 degrees while the lengths of the sides remain constant. Gotta love Euclid!

    • @ThomasCustomWoodworks
      @ThomasCustomWoodworks  10 місяців тому

      Thanks so much for watching and for the thoughtful comment! I just got a little smarter.

  • @gguilliams14
    @gguilliams14 Рік тому

    useing a diagonal brace is esetially the same as putting a full covered back panel on a bench/cabinet. By stretching it corner to corner it basically covers the same amount of area than a full back panel.

  • @indigos290
    @indigos290 Рік тому +2

    Horizontal cross members in a frame don't handle the shear forces well. The horizontal member will help the compression based shear forces from collapsing in and also will prevent the tension based shear forces from collapsing out. Triangles are the strongest known shapes.

  • @mikemiceli8574
    @mikemiceli8574 Рік тому +1

    I didn't realize that I really need one of these until I saw your video. Thanks for sharing!

  • @bwasman8409
    @bwasman8409 10 місяців тому

    A workbench with a new slant and purpose...smaller size and fold away! Well done and thank you!

  • @Raphael-pt7rx
    @Raphael-pt7rx 11 місяців тому

    6:17 cause it ensures the diagonal length. if the diagonal cant change, the whole square cant move/wiggle

  • @pablor3138
    @pablor3138 5 місяців тому

    I have a shop in the city but sometimes i go to my cabin and do some work there, this is perfect.

  • @michaelnovak9766
    @michaelnovak9766 11 місяців тому

    With your notched out bottom 2 ×4 ...I suggest you screw two slightly larger metal plates to the ends of this removal rail
    so your foldable ends can't spread apart.
    Fitting small right angle wooden guusets/right angles.. is also a good way to make your table frame stronger or other projects without having to put in larger diagonal braces.
    Although the one in your design is at the back so only becomes a pest if you want to add removable shelf's to this design.
    Nice and compact.
    I used brass luggage latch hinges once in a over head storage compartment I built in a van . They are easy and work well.
    Nice compact design. 🙂🙏

  • @heut4384
    @heut4384 3 місяці тому +1

    It's not really for a heavier stuff in this working bench, but it's definitely a good space table for my wife's craft projects. 😊

  • @garagengio
    @garagengio Рік тому +6

    Grüß dich Thomas,
    I really love the build and I was planning a very similar design to yours in my head for some weeks now. I will definitely build one like these but add a little bit Garagen Gio style. Hope I'll be able to do a video myself and get your opinion on my ideas. You did a great job. I do not only love the build but the calm video editing is quite refreshing and different to the other channels I follow. I'm glad I found you!
    Viele Grüße from Germany wünscht der Garagen Gio

    • @ThomasCustomWoodworks
      @ThomasCustomWoodworks  Рік тому +1

      Thank you so much for the kind words and feedback. I’m excited to watch your video when it comes out!

    • @garagengio
      @garagengio 10 місяців тому

      Hi Thomas, now you have been working with your bench some time. Do you think it will be necessary for stability to do some diagonales at the side pieces an not only in the back piece? I don't want to use the stretcher underneath the bench because i would like to use the space for storage. In the end I think anyway it will be trial and error. But would love to hear your opinion.@@ThomasCustomWoodworks

  • @AG-cg7lk
    @AG-cg7lk 11 місяців тому +1

    Very nice design. I love space saving solutions like this.

  • @khayes9702
    @khayes9702 11 місяців тому

    That’s an awesome table. I know nothing about woodworking but I am definitely going to try to build this or the other table you build to hang on the wall!

  • @JPToto
    @JPToto Рік тому +2

    Nicely done, Thomas! 100% on the parting words, too 👍🏻

  • @stuartkorte1642
    @stuartkorte1642 11 місяців тому

    Very nice. I slight modification would be to make the fixed table top 12” deep and add a thin backstop. Folded up, the bench could be used as a mini bench or a shelf. Either way, nice bench.

  • @KevinPeffley
    @KevinPeffley 6 місяців тому

    Super. So well thought out and for every issue you had, you were able to find a solution. Very impressive.

  • @humansnotai4912
    @humansnotai4912 11 днів тому

    Great design, build and presentation. Namaste x

  • @olieboer
    @olieboer Рік тому +1

    Hi. Nice build. Is there a specific reason why you didn't recess the hinge pins so that the tabletop in the horizontal position would close the seam between the back side and the table top?
    Also, if you had placed the diagonal bracing between the back legs in stead of behind them, you would have saved another 2 inches or so of floor space.
    If you make it nice and tight, the construction itself helps even more with rigidity, although the added benefit would only help against one direction of racking.
    Making a recess around the back and glueing in a sheet of hardboard or ply would be the best option imho

  • @yeders
    @yeders 11 місяців тому +1

    Looks awesome. Can you update your plans bundle with these plans?
    Also, I'd buy your plans in an instant if you gave a metric version.

    • @ThomasCustomWoodworks
      @ThomasCustomWoodworks  11 місяців тому +1

      Yes I am planning on updating my complete shop plans bundle with this plan. Great feedback!

  • @guyh.4553
    @guyh.4553 9 місяців тому

    Okay you turkey! How dare you make something useful and practical! So mad at you that I just had to subscribe! 😂😂😂
    Very much like this. I have always worked out of a small workshop or no shop. Plus I've moved too many times that ive needed practical work spaces that have to be movable. Thank you for this!

    • @ThomasCustomWoodworks
      @ThomasCustomWoodworks  9 місяців тому

      Haha you’re very welcome! You definitely win the award for best comment.

  • @peterdement
    @peterdement Рік тому

    Consider adding a whell near the table top. Then you may tilt the bench vertically and store it vertically taking up less than half of the wall space needed to store it horizontally..

  • @toolooselowtrek7523
    @toolooselowtrek7523 Рік тому

    I really appreciate your attention to safety!

  • @dougphillips5686
    @dougphillips5686 6 місяців тому

    You need a way to attach your notched support to the back side of the bench, otherwise that piece of wood will get lost or forgotten. Maybe attach with toggle latch.

  • @scoop-pm7lk
    @scoop-pm7lk 10 місяців тому

    geeze ! I just use 2 saw horses and a piece of pywood for my bench ... that ones nice

  • @tonyg8471
    @tonyg8471 11 місяців тому

    You will find architects use triangles in bridge and building construction. Structural rigidity and strength through geometry. Cool workbench!

  • @clarksardido2567
    @clarksardido2567 Рік тому

    I've been looking for a folding workbench design for some time, and I think I found it. Thank you for sharing. Your subscriber from the Philippines 👏

  • @peterdement
    @peterdement Рік тому

    Consider letting in the diagonal brace to further reduce the over all table width..

  • @williammaxwell1919
    @williammaxwell1919 Рік тому +1

    Simple but good solution to limited shop space.
    Next time, make a template for routering recesses for the hinges and only route to the thickness of the hinge.

  • @randytellez2451
    @randytellez2451 Рік тому

    I just might try that build after the holidays. Thank you

  • @robbo9566
    @robbo9566 Рік тому

    Yep, drop leaf table on wheels! A useful workshop application especially where space is at a premium. Just need an idea for a compact vice now

  • @anyname38
    @anyname38 Рік тому +8

    It's only a workbench, but as an apprentice joiner, I was taught to align the wood grain of the dowels with the main piece. Helps them blend in better.

    • @skaylingop9673
      @skaylingop9673 7 місяців тому

      Yes, to my understanding, in woodworking, dowels are typically aligned with the grain to ensure strength and stability. Some people may also prefer a more “seamless” look. However, placing dowels perpendicular to the grain can indeed be used as a design feature to create visual contrast or highlight specific elements of a piece. This technique can draw attention to the craftsmanship and add aesthetic value, though it's important to consider the structural implications since cross-graining can potentially weaken the joint due to differing expansion and contraction rates of the wood fibers. If the primary concern is aesthetics and the structural demands are minimal, using dowels perpendicularly can be a creative choice worth considering.

  • @kdawg925
    @kdawg925 6 місяців тому

    Nice work! Also if they remake Ferris Bueller’s day off, you should try out for the Economics Teacher spot.

  • @robertharris1748
    @robertharris1748 Рік тому

    Nice folding table, and I love the idea since I definitely have space issues. BUT (sorry!) without any vises, I'd argue it's not really a "workbench". Particularly not without some sort of way to fix boards down (for planing etc.)

    • @stuartkorte1642
      @stuartkorte1642 11 місяців тому

      Dog holes and clamps?
      There’s always the clamp on vise. One of my work benches doesn’t have vise, it’s on a heavy pedestal

  • @martint710
    @martint710 6 місяців тому

    Great Video... you're the Mr. Rogers of Woodworking...

  • @PotatoSmashes
    @PotatoSmashes 3 місяці тому

    diagonal support works better because triangles are the most sturdiest shape known to man. horizontal or vertical beams are taking all the weight directly whereas diagonally, its more evenly distributed.

  • @seriously195
    @seriously195 10 місяців тому

    Too funny: when you said "remember when...", you sounded just like Andy Rooney (60 Minutes commentator). Probably well before your time. Nicely done and I will be making one this summer/

  • @Bloozestringer
    @Bloozestringer Рік тому

    Looks like it'd make a great table, but probably moves all over if you're trying to clamp something down and use a hand plane or other hand tools that require some leverage.

  • @edmc755
    @edmc755 2 місяці тому

    Love your built, but when it is folded , does it not tip over to the front very easy ??? The bench when folded is not very wide , so it could tip forward very easy ?????

  • @ClarkeLSmith
    @ClarkeLSmith 11 місяців тому +1

    Hi Thomas, thanks for sharing this video and nice work! I have 2 questions:
    1) would one be able to double the table's capacity by making the same fold down but on BOTH sides... and use either one or both sides depending on the total table space one needs
    2) If you had used SOSS type hinges, would you have been able to eliminate the gap seen between the 2 table surfaces?

    • @ThomasCustomWoodworks
      @ThomasCustomWoodworks  11 місяців тому

      Thank you!
      1. Possibly, but it would be too big for my space and it would be roughly double the size folded up making it not quite as space efficient.
      2. I have not heard of those until now but I just looked them up and depending on the weight capacity it could be a great way to eliminate the gap. Let me know if you try it!

  • @lunatik9696
    @lunatik9696 Рік тому

    Cool workbench.
    A horizontal brace still allows the corners to bend/ sway as it only supports in 1 axis.
    The cross support works better as it prevents the corners from swaying in 2 axis.
    One could use trigonometry and determine the vector and moment forces.
    The result is corner pushing forces are balanced by forces pulling from the other corner.
    I didn't see the background music credited.
    Is it your original music?
    I barely heard it, but liked it.

  • @gregmize01
    @gregmize01 Рік тому

    Well this work bench is certainly KIND of AWESOME! Great job!

  • @pathardage1880
    @pathardage1880 Рік тому

    Good idea. I'll have to think about this one for my shop. Thank you.

  • @michaelhyland9216
    @michaelhyland9216 11 місяців тому

    It looks like you could build two and them connect them to make a larger table if you needed more area.

  • @johnford7847
    @johnford7847 Рік тому +5

    Nice build and nice design. I think a lot of people would find this useful. Thank you for sharing.

  • @jablot5054
    @jablot5054 5 місяців тому

    Good idea with the clamps

  • @MyGrowthRings
    @MyGrowthRings Рік тому

    This is great, and oh so close to an idea I’ve been working on. Well done. Scott

  • @remmingtonsteele2562
    @remmingtonsteele2562 Рік тому

    That bench is pure awesome
    Thanks for sharing !

  • @indianafanatic
    @indianafanatic 2 місяці тому

    I bought the plans for this bench and had a question: By trimming off the rounded edges of the 2x4 lumber, effectively making them 3" in width, what considerations do I need to make in altering the cut list? Off the top of my head, I can see that the long additional leg pieces will need to be an inch longer (pg 20), but can you think of anything else I need to address? I appreciate your paving the road for us making this workbench and can't wait to see how I do with it. Thank you.

    • @ThomasCustomWoodworks
      @ThomasCustomWoodworks  2 місяці тому

      I cut off 1/8” on each side making each 2x4 piece 3 1/4” wide. I cannot think of anything you will need to address as the plans are catered to 3 1/4” wide boards but I would just use referential measurements when cutting each piece to make sure they fit. Any other questions please email me at ts.gojkovich@gmail.com as I may miss some comments.

  • @michellebascombe6265
    @michellebascombe6265 4 місяці тому

    Hi Thomas, what would happen if I didn't recess the hinges? How would that affect the dimensions of the table folding up?

  • @RayCollins-dv4ts
    @RayCollins-dv4ts 7 місяців тому

    Inspiring design with a good execution.

  • @sarinhighwind
    @sarinhighwind 2 місяці тому

    Im over here with a 4'x8'.
    Limited space sucks. Like when your huge workbench turns into a storage shelf.

    • @ThomasCustomWoodworks
      @ThomasCustomWoodworks  2 місяці тому

      Yeah everything with a flat surface is a storage shelf at one time or another.

  • @nutsmcflurry3737
    @nutsmcflurry3737 14 днів тому

    Was the folding top issue because of routing the hinges in too deep?
    Normally they are let in to the thickness of the metal.

  • @bigrobbo75
    @bigrobbo75 Рік тому

    awesome effort, Hello from Auckland , New Zealand

  • @dancoleman8467
    @dancoleman8467 11 місяців тому

    I love this. I want to build one similar. Great idea. Just what I need!!

  • @WoodworkingTop535
    @WoodworkingTop535 6 місяців тому

    Watching this video, I learn many new things, it's very fun, thanks

  • @SeaFanStudio
    @SeaFanStudio Рік тому

    Nice workbench! I agree that this one uses less valuable wall space than the first.

  • @dolphinsleap
    @dolphinsleap Рік тому

    I especially like and appreciate the honesty of your statements. "why did I do this way? because I felt like it!" hehehe

  • @pohkeee
    @pohkeee Рік тому +1

    Triangles are the most stable…thus geodesic domes and all manner of trusses…

  • @qhadj5387
    @qhadj5387 9 місяців тому

    I didn't understand how the latch got in the way. Then I see you routing on its side which I don't get how it helps. Thanks

  • @ReneeNme
    @ReneeNme 3 місяці тому

    An even sturdier support system than just a single angled brace is an X pattern.

  • @tims.2832
    @tims.2832 6 місяців тому

    “I had to do it with the jigsaw on the other side” caught me off guard, very funny 😄

  • @garagengio
    @garagengio Рік тому

    Finally the waiting has come to an end ❤

  • @pauloconnor2
    @pauloconnor2 11 місяців тому

    Great video thanks for sharing. Is there a way to mount a vice to this bench?

  • @timpenner7858
    @timpenner7858 Рік тому

    the thing about rethinking the workbench, i see a sturdy folding table. you even keep saying tabletop and not benchtop. benches are large wood-holding jigs. you should add a few features for doing it.

  • @edwardgrossman295
    @edwardgrossman295 Рік тому

    A angle 📐 brace over a vertical brace is better because a angle brace counter acts Compression and tension it’s a vector sum of algebraic properties; a vertical brace translates or transfers load down. This is the Basis Engineering 101 definition 👍

  • @carlosmacmartin4205
    @carlosmacmartin4205 8 місяців тому

    "Everybody has the ability to be creative." That's a fact!

  • @davivify
    @davivify Рік тому

    A triangle is one of the most stable structures known to man. So by adding a diagonal you are, in effect, creating a pair of triangles, which will strongly resist racking.

  • @globyois
    @globyois Рік тому

    Love it! Great job!
    Yeah, how can I get the video and plans?

    • @ThomasCustomWoodworks
      @ThomasCustomWoodworks  Рік тому

      Thanks! Click the link in the description or go to www.thomascustomwoodworks.com.

  • @Richard-id-000
    @Richard-id-000 Місяць тому +1

    good idea .. good job

  • @4b0d3
    @4b0d3 Рік тому +1

    I never really understood the point of the fold up work benches. where do you store all your wood? If you make a large bench 8' long, you can store so much wood under it You can build off sections for different types and different sides. Just get wheels rated for 350+ lb each and you're set. you can wheel it around the room. I get that it saves room, but where is your other stuff being stored? and I'd argue that a large strong wheeled bench is a better option that incorporate many other space wasting pieces.

    • @richpalmisano1740
      @richpalmisano1740 9 місяців тому

      Roll away outfeed is a good appl8cation for those without a lot of space

  • @b3arwithm3
    @b3arwithm3 Рік тому +2

    That's a very clever design. I would add another toggle latch on the back legs, to lock it when it is in its closed form. I am wondering how it can be modified so that I can roll it around while closed. I have even less space 😢

    • @ThomasCustomWoodworks
      @ThomasCustomWoodworks  Рік тому

      Thank you! I’m not sure how to modify this to role around while closed but that doesn’t mean it can’t be done.

  • @Ceen328
    @Ceen328 5 місяців тому

    06:30 triangles are the most sturdy shape

  • @williamdoyle649
    @williamdoyle649 Рік тому

    This is a great design! Well thought out

  • @jjjrican3544
    @jjjrican3544 7 місяців тому

    Great build keep up the good work 🤘😎

  • @ednowliniii
    @ednowliniii Рік тому

    “I didn’t feel like it”. LOL, love it.

  • @improveyourwoodwork11
    @improveyourwoodwork11 8 місяців тому +1

    The best way to join one piece of timber to another, as required for joining the legs to the rails of the frame, is with mortise and tenon joints. End of story!

  • @dkaustin98
    @dkaustin98 Рік тому

    I am disabled vet with deteriorating spinal disease. I built a folding workbench with a lift off top and I built my table saw stand so I could use it as an outfeed table. Unfortunately I have to move the wife's car out of the garage to set up my shop. Yet, I have had another spell with my back from a fall with a shop stool. I find the top is now too heavy for me to lift on my own without back pain. I do believe this build will suit my needs.

    • @PaulTiseo
      @PaulTiseo Рік тому

      Try using gas struts for some assitive help.

    • @dkaustin98
      @dkaustin98 Рік тому

      @@PaulTiseo I have an unused pair that I can use for this project.

    • @ThomasCustomWoodworks
      @ThomasCustomWoodworks  Рік тому

      I’m glad this workbench will help.

    • @dkaustin98
      @dkaustin98 Рік тому

      @@ThomasCustomWoodworks The trick will be modifying or converting what I built into this style. It is doable.

  • @rodsquad911
    @rodsquad911 11 місяців тому

    You’re a good man Charlie Brown

  • @seant346
    @seant346 15 днів тому

    "i didnt feel like it" perfect

  • @kjellandrew
    @kjellandrew Рік тому

    I want to support you and buy the plans, but I have two issues that I wouldn’t know how to resolve. 1. The screws on the small top are a hard no. I imagine I could pocket hole the top down or something. 2. The biggest one is the gap. In a drop leaf design, it doesn’t make sense for there to be such a significant gap. Can that be fixed?

    • @ThomasCustomWoodworks
      @ThomasCustomWoodworks  11 місяців тому

      1. You could potentially use pocket hole screws to attach the small table top.
      2. The hinge has a “bump” in the middle which is why it was not possible to decrease the gap with the hinges I used. There may be hinges that are completely flat across the entire hinge but I do not know for sure.

  • @bcase5328
    @bcase5328 Рік тому

    You call it a work bench. I see potential for it as an apartment or tiny house table, (or as a heavier camping table).

  • @BigTuna762
    @BigTuna762 Рік тому

    What are those hinges on the wings of your mitre saw station called? Those look like a perfect solution for what Im trying to do!

    • @ThomasCustomWoodworks
      @ThomasCustomWoodworks  Рік тому

      They are 16” folding brackets and the brand I used was Yumore from Amazon. They have worked well.

    • @BigTuna762
      @BigTuna762 Рік тому

      @@ThomasCustomWoodworks awesome! Thanks so much!

  • @KevinTyson-s9n
    @KevinTyson-s9n Рік тому

    Great workbench thanks!! Will you be making a bundle available for this bench and the 2 for 1 tool cart?

    • @ThomasCustomWoodworks
      @ThomasCustomWoodworks  Рік тому

      I definitely can! Send me an email and I’ll work it out for you: ts.gojkovich@gmail.com

  • @myspacenrg
    @myspacenrg Рік тому

    wondering if you could sub a piano hinge in place of the door hinges to tighten the gap between the dropleaf section. or if it would still persist the issue of the dropleaf not sitting 90 degrees down prior to your notching, after the fact.
    great job. exactly what im looking to replicate, give or take, the size.

    • @ThomasCustomWoodworks
      @ThomasCustomWoodworks  Рік тому

      Thanks! I just would worry that the piano hinge wouldn’t quite be strong enough.

    • @myspacenrg
      @myspacenrg Рік тому

      @@ThomasCustomWoodworks fair point/concern

  • @carolmoore3706
    @carolmoore3706 4 місяці тому

    Love this thank you for sharing

  • @yeders
    @yeders 11 місяців тому

    Curious, why have you opted for a bought aluminium table saw sled vs making your own?
    Have you done the 5 cut square test to see how accurate and square the aluminium sled is? Really keen to know, as my old sled doesn't fit my new table saw

    • @ThomasCustomWoodworks
      @ThomasCustomWoodworks  11 місяців тому

      I had some scrap plywood so it was cheaper and it’s really accurate as I did the 5 cut method (with instruction from the Wood Whisperer).

  • @bowlerhatman01
    @bowlerhatman01 Рік тому

    I'm curious about how screws followed by dowels are simpler than just dowels?

    • @ThomasCustomWoodworks
      @ThomasCustomWoodworks  Рік тому

      It’s just my preferred method.

    • @janburger4230
      @janburger4230 Рік тому

      What I like about the screws is the pulling force on the glue and the time saved on the clamping and that I can continue working while the glue is drying.
      With dowels only, clamping force is needed for woodglue adhesion to work at its best.
      I like to remove the screws after the glue has dried, then drill the screw holes bigger and drive a dowel with glue in there.
      Looks nice, feels nice, strong and no chance of future surprises of metal and woodwork tool collisions.

  • @lisagooden1628
    @lisagooden1628 День тому

    Thanks

  • @nehennings
    @nehennings 10 місяців тому

    The Step Brothers reference - chef’s kiss