Thanks so much for this video. You gave me a great understanding of the wall mount installation process. Even years later your video is awesome. I definitely subscribed!
Hi Kiana great question. From what i can tell in the manual There should be plastic or rubber spacers included in the installation kit that would be used to fill the space between the arm and the back of your tv in the areas that are uneven .
First you have to find the formation that is specific to your tv and then the arms attach to the plate at different point using 4 screws. I hope that helps !
Hey Bryan which drill did you use to drill those 2 first metal screws onto the wall? I got a cheap one from Walmart for $20 and It's not strong enough. Also which screws did you use? I couldn't tell. The instructions say to use 1, which are the long ones. The end of yours looked different though. Thanks man.
Hi heather. I dont recall having any issues with the screws they provided. Im not home right now but when i get back i will check and post the size and type of screws i have on there.
Hi heather. I used the M6 x 8mm bolts which are provided . If youd like to send me a picture of ur mount on my fb or instagram i would be happy to send you some pictures of my setup. @bryanbuilt20
Hey ! sorry for the delay. I Didn't predrill holes I went strait into the drywall and stud and for the screw it was just a regular phillips tip since i used a phillips head construction screw.
Hey dave . Is it going forward or is it goingntonone of the sides? It has the two bollts with the allen wrench and it also has a turn knob that controls the forward tilt
@@BryanBuilt Thanks Bryan - it keeps wiggling side to side. I have loosened and again tightened the two bolts with the Allen wrench but it neve tightens enough. Any thoughts would be great.
Hmm thats weird . When you tighten does it hold for a couple of days and then get loose or is it just not tightening at all? Also are there washers on the bolts? Sorry for so many questions 😅 just trying to think of reasons it would loosen.
@raimoore4945 Exactly what I was thinking. It might have been obvious to him, but to me, it may as well be Greek. The screws fit one piece but not the other, so how did you do it??
You made this way more difficult, and I came here for help figuring out a few things, and you sped through it.
sorry about that always working on making these videos better thanks for the feedback
FINALLY, directions that I can understand! You rock!!!
Thank you for the install tips. Love that you made it a family affair. 👍🏼
Thanks for watching! I always try to get them involved where i can
Thanks Brian for showing the install. Always nice to see it done before doing it yourself
Thanks for watching!
Thanks so much for this video. You gave me a great understanding of the wall mount installation process. Even years later your video is awesome. I definitely subscribed!
Hey thanks for the video - can you please explain how to attach the arms? It says to use bolt #3 but a bolt by itself won’t hold the arms.
Would u recommend mounting when the wood stud are 14 inches apart instead of the 16 inches recommend?
Yeah this model is installed vertically so you only need one stud it has 3 screw holes that run along the same stud
Nice installation video, enjoy the TV! Thanks for the feedback in regards to the Allen wrench!
USX Mount Thank you for checking it out! Love the mount and just wanted to share my experience!
tilt 15- downgrade with knob screw, thats great , im going to order one for my x900h 55 inch
You should get a stud buddy things work great
Ill have to check them out i do need a good stud finder
How would you put the arms on the plate if the back of the tv is not flat like the back of yours is
Hi Kiana great question. From what i can tell in the manual There should be plastic or rubber spacers included in the installation kit that would be used to fill the space between the arm and the back of your tv in the areas that are uneven .
How did you put the arms on the plate
First you have to find the formation that is specific to your tv and then the arms attach to the plate at different point using 4 screws. I hope that helps !
Hey Rahma just wanted to follow up and see if you were able to get those arms attached to your plate ?
What is the head size of the lag bolt? American or metric
I believe it was a 3/8 by 2 1/2 inches
Hey Bryan which drill did you use to drill those 2 first metal screws onto the wall? I got a cheap one from Walmart for $20 and It's not strong enough. Also which screws did you use? I couldn't tell. The instructions say to use 1, which are the long ones. The end of yours looked different though. Thanks man.
Hey thanks for watching! I used a dewalt 20v drill driver and the screws i used 3 inch wood screws with a washer on the end .
Thanks Bryan great job on the video.
Thank you!
How did you connect the extensions to the plate?
The screws they say to use aren't long enough to hold the arms onto the mount.
Hi heather. I dont recall having any issues with the screws they provided. Im not home right now but when i get back i will check and post the size and type of screws i have on there.
Hi heather. I used the M6 x 8mm bolts which are provided . If youd like to send me a picture of ur mount on my fb or instagram i would be happy to send you some pictures of my setup. @bryanbuilt20
What size drill bit did you use?
Hey ! sorry for the delay. I Didn't predrill holes I went strait into the drywall and stud and for the screw it was just a regular phillips tip since i used a phillips head construction screw.
Our will not stay level? We lossened the Allen wrench screws relevel and tightened, but still keep unfeeling itself. Any thoughts?
Hey dave . Is it going forward or is it goingntonone of the sides? It has the two bollts with the allen wrench and it also has a turn knob that controls the forward tilt
@@BryanBuilt Thanks Bryan - it keeps wiggling side to side. I have loosened and again tightened the two bolts with the Allen wrench but it neve tightens enough. Any thoughts would be great.
Hmm thats weird . When you tighten does it hold for a couple of days and then get loose or is it just not tightening at all? Also are there washers on the bolts? Sorry for so many questions 😅 just trying to think of reasons it would loosen.
If youd like to send me a picture of ur mount on my fb or instagram i would be happy to send you some pictures of my setup. @bryanbuilt20
@@BryanBuilt not it just does not tighten at all. Bit is tight, but not solid. No washers. I will send photos and other soon. Thnks
Thanks
Totally skipped the part i needed.. how to put the arms on the plate. 🥺
@raimoore4945 Exactly what I was thinking. It might have been obvious to him, but to me, it may as well be Greek. The screws fit one piece but not the other, so how did you do it??
Thank You!
Thanks for watching!
do you have to find the stud?
Yessir i did
mounting a tv with no stud finder is crazy
Watching this video made me so made cause why you ain’t slow down and showed us nothing but you installing . How tf I supposed to put this shit on
Sorry! What part are you having trouble with?