Easy Picture Frames with the Master Frame-Making Router Bit Set
Вставка
- Опубліковано 6 жов 2024
- Infinity Cutting Tools - 00-516 6-Pc. Master Frame Making Router Bit Set
More Info: www.infinityto...
Blog: www.infinityto...
Subscribe: www.youtube.co...
Facebook: / infinitycuttingtools
Twitter: / infinitytools1
Instagram: @InfinityTools ( / infinitytools )
Products Used:
Professional Router Table: www.infinityto...
Bow Products Featherboards: www.infinityto...
Dadonator Stacked Dado Blade: www.infinityto...
Incra Crosscut Sled: www.infinityto...
iGaging 6" Combination Woodworking Square: www.infinityto...
Adjustable Four Corner Frame Clamp: www.infinityto...
NOTE: The part number for the Adjustable Four-Corner Frame Clamp above has been changed to 100-595.
I appreciate the detail in the video.
Thanks for watching!
Thanks , you teaching is the best, April First /2021-Gracias!! Bronx-
great video! everything looks more easy with those bits.
Jaguar Hdz now
Frame making "best practices" -- very useful!
Nice work
I like the details on making the profiles. However, you seem a bit careless operating that table saw. Just saying if you value those digits be a bit more careful and use a guard. To many moments made me cringe thinking you were going to lop off a finger or 2
Great bro , I like it , soon will order it
thank you for sharing on my video
awesome tools great work by infinity
Yash Nis
Thanks
Wow, 👍 for sure I’m going to order my.
Use sawdust to clean up the wet glue squeeze-out 😉
nice job, was wondering, what router did you use to hold the 1/2 bits?
We're very fond of Triton routers in the Infinity shop. Good design and performance. www.infinitytools.com/ssearch?q=triton+routers
@@InfinityTools thankyou
U rock Andrew... Thanx
In your opinion, what are the preferred steps? Cut miters and lengths, then cut the profile, then use the stepped router to make the rabbet? I was thinking to cut the rabbet on the straight pieces, then route the profiles on each straight piece and lastly measure and cut the pieces/miters to the correct lengths. Thanks for your help on this.
My preferred process is to create the profiles and the stepped rabbet on the longer pieces, and then miter them to length to create the frame. Always remember it's easier to trim a piece a little at a time to sneak up on the fit than to try and make it perfect the first time.
Love bit set but will it fit a craftsman 2hp router?
Beautiful
sir I need these router bits. these very important tools for my shop.
very good
Awesom evry chamasyri fo de fo bo
I need those tools.
An excellent video but what resource do you use so know you are making the correct length right and left side and a correct size top and bottom rail for the size picture you want to frame? That’s what I struggle with And is there a recommended reveal size for the mat sides and top and bottom?
Ron
You probably dont care at all but does anyone know of a way to get back into an Instagram account??
I was stupid forgot my login password. I would appreciate any assistance you can give me!
@Amir Dariel instablaster ;)
@Benedict Ahmir I really appreciate your reply. I got to the site on google and im in the hacking process now.
Takes a while so I will get back to you later with my results.
@Benedict Ahmir it did the trick and I now got access to my account again. I am so happy:D
Thank you so much you saved my ass!
@Amir Dariel Happy to help =)
How this is the stock used in this video? Can I use 3/4 inch thick wood?
Stock thickness would be personal preference and dictated by your project.
Can they be used with a hand router or they are best suited to a router table?
buen dia muy buena explicacion sobre como usar las diferentes fresas para router, una pregunta sr, perdon por la ignorancia como se llama la pieza que usa para armar el marco y donde lo puedo conseguir, felicitaciones DIOS lo bendiga, saludos desde, huatabampo, sonora mexico
Hi, you are looking for a frame clamp. www.infinitytools.com/four-corner-frame-clamp
Ki
King hnnhjjhyvbrfhungnhfggvbhhgybghhy
"I'm going to show you some of my tips for getting perfect mitres"
"First, buy $10,000 worth of equipment"
Great video. How do you adjust the Incra miter gauge if it doesn't register a perfect 45 degree angle?
Basic adjustments to just about any Incra Miter gauge are done at initial setup when squaring the gauge, usually this is a matter of loosening a couple of screws and squaring the gauge to the miter bar and tightening everything back up. if you use a square like i did in the video to check the angle, you can set the gauge either by the stops built into the gauge which I have always found to be accurate, or simply by using the square and locking down the gauge without using one of the built in stops.
I see that you make flat moldings can they be used to make a beveled shape.
When you say "pin the frame with brads", which is it? Pin nails or brad nails? It looked like a pin nailer. I just wasn't sure if I needed brads or if pins are enough until the glue dries...
Either should do the trick for average sized frames.
Do you include a router bit setup chart with bit sets?
Hi Ron, we do not have a setup chart but each of our bits have a recommended speed chart printed on the back of the pouch they come in. This helps insure that you have the bit running at roughly the correct speed so that you can fine tune the RPM to suit your material and depth of cut.
Muy buen video !!! Pero deveria agregar traduccion al español en letras.
Are these coming back , not on website anymore?
James, Yes they're still in stock. We're having some site issues and should have everything back in working order today. We appreciate your patience.
Kool
Man !!! Use a Push Stick Dude !!!
Making frames really suck! I guess I just didn't have the right equipment. Thank you.
Do you ship to canada?
Yes, we can ship to anywhere in the world.
El contenido esta excelente...pero se disfrutaria mejor si tambien se tradujeracal español...digo...si los posibles clientes no hablan ingles!!!
do you glue and pin for the strip
I just glued and clamped. If using pins, make sure not to put them where you will need to cut and be careful of the length of the pins.
do you sell in the uk?
Yes we do! You can place an order with us on our website, we ship all over the world. You can see all the details of our shipping policy and options here, www.infinitytools.com/shipping-policy
I want to buy this set
At this time, they're out of stock :(
👍
all i have is the incra 1000hd
you should be able to do just about anything you need to with a 1000HD. I worked for years with the 1000SE with no complaints,
ए किट की कीमत बताओ
Solo entiendo en Español
Boyer
Kreaktif
Hay de 1/4
hi, this set includes bits with both 1/4" shank and 1/2" shank. to use this set you would need a router with a 1/2" collet.
Ok
nic
LOL
Thank you my friend....
What's app please
None of these are 1/4" shank bits. Not worth it.
Actually one of the bits in this set is 1/4" shank. As this set is intended for use in a router table and not recommended for free hand routing, 1/2" shank router bits should not be a concern.