Thanks a lot, this is the best video I could find on how to disassemble but also reassemble the mower back. I need to change the motherboard battery as the time and date resets randomly. Kudos!
Thank you very much for your video. I was very nervous at the thought of disassembling it. But with the help of your video I got the courage to do so, so thanks for the great guide.
Thanks for the video! My model is not exactly the same but I guess the procedure is similar for disassembly, in my case to be able to replace the front wheels which have detoriated quickly this year to the point of getting totally stuck. I have the WG796E model, replaced the front sensor last year without disassembling - there was enough slack in the cables to pull the contacts through the hole and unplug the old sensor and plug in the new one from the outside. It was difficult to get the seal perfectly in place for the new sensor and I will check this as well. Excellent instruction, especially regarding how to remove the height adjusting knob which would be almost impossible to guess!
Thanks man. Your video saved my robot. I disassembled it and found the broken wire at the front sensor and replaced it. Now, the mower is working fine again. Great
It is always good to know how to repair. Although next time: you actually only need to unscrew the sensor (4 screws) and wiggle out the cable from the bottom… :) My question to you: I have to replace a cable and wonder what sort of cable it is.... It is not a copper cable. What did you use?
@@eblita3698 Hi there. I just jused one of the cables from my arduino-tinker-projects. But - just today - it broke again (after having it repaired two times already). I think i will have to replace the sensor completely now. I hope i'll be able to buy it somewhere..... And thanks for the hint with the sensor-Screws ;-)
Hi gsbox, -though next time: you actually only have to unscrew the 4 screws at the sensor and then wiggle the cable out from the bottom…. much easier. I have a question: will you tell me what kind of cable did you used? I see it is not a copper cable…..
Stort tack för instruktionen. Funkar klockrent! Vad man bör tänka på är att trycka fast det nya kabelpaketet på "rätt håll" så att man inte behöver vrida kablarna när sensorn ska skruvas fast igen. Det misstaget gjorde jag men orkade inte gå hela vägen tillbaka igen. :) Det får bära så länge det går. Suverän film!
I did the layout and installation by studying the on line videos Husqvarna had on the web ua-cam.com/users/postUgkx2KDztGvdU79XTmlqIMSUyPq8CjprGJOR also recommended it When I started the unit it stated it would take a few days to learn all the spots in the yard. So I thought it was just finding the areas till I noticed it was cutting. It is so quite you don't know it is cutting.
My out of bounds error experience. First thanks for the video, sure helped getting it apart. Mine started one day about a month ago with the outside working area error. Reset it and it worked again. This went on for a couple days and then the error was permanent. Looked at the wiring harness to the front sensors and it did not look so good. Took it apart and removed the front sensor and charging assembly. I could not find any broken wires but I replaced it anyhow. While I was in there I replaced the lcd display since that had not been working right for awhile, Chinese characters or blank once it was on a few seconds. Put it back together but the same error, permanent out of boundary error, at least the display worked again normally. I think now wtf? I'm thinking maybe weak signal from the base station. Green light looked good, steady on green, flashed when I disconnected the wire, steady green when connected again. Then I decided to get a separate wire about 20m long and hooked it up instead of the permanent wire. Laid it on the ground in a big loop in the yard. Put Harry in the middle and no error and it worked like a champ, Again wtf? So I start thinking about the splices of wire I soldiered in to adjust the boundary several years ago, my wire has been in 6-7 years. Since it rained here a lot in August I'm thinking maybe one of these splices got wet through the heat shrink I used to insulate the wire and is grounding out the signal. Ripped all these places up and redid them, no luck. So now I get a box of wire and I ripped out all the original wire. One place where I pulled it up separated very easily. This spot was near where moles were digging and the wire ends looked chewed or scrapped from the moles, frayed. We have a lot of moles here in Germany and the mower keeps them out of the yard but they dig around the boundary. So it looks like they damaged the wire but not enough to cause the green led to flash but enough to cause the errors. After installing a totally new wire Harry is working just fine now. I bought my parts online at letmerepair-direct.de
Thank you for your video, thanks to you I was able to change the charging block which had a cut wire, thank you very much it helped me. my robot charges perfectly, but now it no longer wants to leave its base, it moves back 50 cm and stops then beeps constantly. I tried to start it outside its base and it's the same thing. maybe I made a mistake when going back up? the front right connector seems out of order, via the robot screen but the block is new!
Mycket bra video, har tyvärr fått byta frontsensor två gånger på min de senaste 3 åren för att de tunna kablarna till laddarbläcken bryts av, verkar vara dåligt dimensionerat (eller dålig kvalitet, kanske båda) kablage. Bra med en tydlig guide så att man lätt kan se hur man ska göra. :-)
Great video and great work !!! Can you tell me if there's a way to test/measure the functioning of the left and right sensors ? I'm not sure mine are working ok or not. Many thanks !!!!
Hi and thanks for your appreciation! Unfortunately I do not have any idea about how to test/measure the functioning. But if it begins to leave outside the electronic fence I guess it is a signal of them not working properly.
Jag tackar så mycket för denna detaljerade video. Exakt samma fel på min robot. (En korkad lösning från början) Jag ska beställa en och byta så snart det går. Bra jobbat, tack igen! :)
I was actually able to repair my landroid by watching this video! Thank you so much Kenneth! I do have one problem though. I'm not able to turn the blade height knob to anything lower than 55mm. Did I mount it wrong? Thanks again :-)
Hi, nice to hear that my video has been a good guide for you. Yes, the height knob should work as usual so I'm afraid you have to re-do some of the steps, starting with de-mounting. I made the video a couple of years ago so I do not remember all details of how I did it but I remember that one has to be careful remounting the knob. Do under way tests of it's correct function during re-mounting.
Hej kul att du gillar min video men tråkigt att bytet av frontsensor inte löste problemet. Nej jag har nog inte någon idé om vad som då kan vara problemet. Men eftersom du gillade videon så får du jättegärna prenumerera på min kanal. Det kommer fler videos du kan ha nytta av 😃
Thanks for this great job! But tell me please... What was the "strange things" that your robot did? Mine is slightly turning right and left just like when it find his boundary wire, but it does that in the middle of my garden, with no wire below it to be sensed by the sensor... Pretty crazy... 6 years of use.
@@KennethSteen Thanks my friend. I could fix the wire following your tips and mine worked fine since last time i wrote to you. Like a year. Yesterday it started to run in circles, like 3m diameter. I can see that one wheel is spinnig faster than other, but i don't know if it's a motor issue or circuitry issue. If you guess what may be happening, i'll gladly take your advice. Other than that, as soon as i fix it, i'll share it here, since you may face the same issue someday. Thanks!
@@dayangolanski1250 Hi, that is strange behaviour. I have not encountered that problem myself but I would first check that there is no dirt that hinders the wheel to spin.
Just wanted to say: had a problem with Landroid after rinsing the wheels with water. The keyboard stopped working. Remedy: REMOVE the battery IMMEDIATELY so that no more electricity flows and wait until everything has dried up. Then we went again. Recommendation; be careful when rinsing, especially from below. The keyboard connector should not be adequately protected against water. I will look at it when the opportunity arises and seal it accordingly.
My keyboard has died (didn't rinse it with water, it just has keys that stopped working... One of which is part of the PIN). Did you end up replacing yours, and if yes, where did you buy it from?
hello, thank you for your video, first of all, someone gave it to me because it is broken. I would like to know where i can find the exact reference ? I see yours is the WG791E, where can i check which one is mine ?
Hello, great video. My Landroid stops with the error "elevation" I discover that it is the sensor on the side. The robot stops when the cover which has a magnet lifts from the metal part. Any idea what I could do to keep it going without stopping? Thanks
Thank you for this video. It looks like there is a little space in the front corner(s) above the caster wheels. Do you think that their is enough room to place a gps tracker? Do you remember about how much space might be available? Thanks again.
Hmm, could it be so that one of the wheels are stuck...? Or could it be that the black cover is not remounted correctly. It might give the machine the signal that it has run into something and that it thereby thinks it is stuck.
@@KennethSteen Well, i have checked everything, even changed the trapped sensors. Magnets seems fine.. but still its trapped.. and the issue is that i cant reset by pushing 0. Its not working. The button is working, have tried it in the "date" section just to see if there is a problem with the keyboard.. but no. Im lost.
What kind of error gives you the broken sensor apart from getting stuck on obstacles? Mine Wg794e keeps turning around and then it stops giving different errors every time...blocked wheel, out of aerea, stucked...etc...main problem is i got that from China and apparently different connection on shock sensor..at least the shop told me this and they didnt fix that..any help?
Your comment "make sure the pins holding the silver hatches are in their places" is confusing to me.. Whichs pins are they ? Are these the long round pins that hold the latches and the springs ? I also read something about the two metal parts that are in the frame needing to touch with some pins from the assembly ? Thank you so much !
You don’t need to disassemble the whole Mower! Just drag the rubber out of the bottom and the Plug Connection will follow out of the hole. You can simply unplug and have the Sensor unit free to work.
Hello. I liked a lot of your video. I think I have the same problem with my robot. I searched to buy the bundle of cables in question but unsuccessfully. Would you send me a link from a site in which they offer it? I will be very thankful.
Hej Kenneth hvilken af fejl gjorde din Work? Min er nemlig begyndt med at skrive uden for område når den er 1 meter væk fra ledningen som går rundt i kanten af haven
Hi, I bought it at www.clasohlson.com/se/Frontsensor-Worx-Landroid,-E1-(2016-)/p/Pr513256000 Seems to be in stock also now. Good luck (let your web-browser translate the Swedish into english)
Hi, nice video! It seems that my front end sensor is working. My problem is that the Worx Android stopped charging. I took the battery out and could charge it, but it does not charge when coming to the home base. The light turns red, but after a while goes off, before turning red again. So it seems there is a bad contact between the pins from the home base to the battery. Would it help to change the front end sensor?
Hi, I would look for a reset instruction (I do not remember if I´ve seen such) to reset the Landroid. Also check that all the thin cables are ok (the ones in the front sensor where the pins for charging enters the Landroid).
Bonjour, j'ai l' erreur "élévation" qui s'affiche sur l'écran et la tondeuse s'arrête. Sur l'écran il est écrit appuyer sur "O" Que faire ? j'ai la worx wg 754e.merci
Io ho un problema.quando il robot e sulla base pa.puce passa da rosso a verde e sul display mi scrive fuori area.poi socompare. Il red torna rosso e via di seguito.ho cambiato blocco sensori , batteria ....circuito della base e alimentatore. Stesso problema cosa puo essere?
Hi, I bought mine here www.clasohlson.com/se/Frontsensor-Worx-Landroid,-E-(2014-15)/p/51-3258?gclid=Cj0KCQiAnKeCBhDPARIsAFDTLTL0NXpcDLfO1GPLn4J_Fyi7v5nTA2ZjilQRBgMXSDNXihz-mygiWRUaArUJEALw_wcB
bonjour je n ai plus moyen d allumé mon robot worx landroid wg791e j ai changé la pile de l écran se trouvant sur la platine du circuit imprimé a l 'intérieur (cr1225 3v ) servant pour l écran celle ci était morte 0,5v depuis plus moyen d allumé mon robot !!!! NB/ quand je le mets sur la station sans la batterie la lampe verte vire au rouge j appuie 2secondes l écran s allume et m'indique batterie en charge 0a100%puis me dis code incorrect au revoir puis il s'éteind !!!! si je remet la batterie et que je fais la même opération il ne s'allume pas !!! même si je le fais hors de la station plus moyen de l 'allumé plus aucune touche ne fonctionnent l'écran ne s'allume pas que faire NB ; la batterie est chargée nouvelle batterie merci pour votre réponse si il y a !!!
Att få tillbaka höjdvredet är alltid lika omständigt. Tack för videon👍🏻🇸🇪
Tack för att du tar dig tid och delar den här videon❤
Kul att du gillar den, prenumerera gärna.
Thanks a lot, this is the best video I could find on how to disassemble but also reassemble the mower back. I need to change the motherboard battery as the time and date resets randomly. Kudos!
Thank you for your nice feedback. I hope the best for your coming effort.
You are very welcome to subscribe my Channel 😊
Brilliant video, many thanks for sharing your know how, without it, I wouldn´t be able to analyse the problem and fix the robot..
Tack du har visat allt förutom hur man byta framhjul
Hej, jag har aldrig gjort det men hittade den här videon på youtube ua-cam.com/video/nUss9yhfr8s/v-deo.html
Thank you very much for your video. I was very nervous at the thought of disassembling it. But with the help of your video I got the courage to do so, so thanks for the great guide.
Thanks for the video! My model is not exactly the same but I guess the procedure is similar for disassembly, in my case to be able to replace the front wheels which have detoriated quickly this year to the point of getting totally stuck. I have the WG796E model, replaced the front sensor last year without disassembling - there was enough slack in the cables to pull the contacts through the hole and unplug the old sensor and plug in the new one from the outside. It was difficult to get the seal perfectly in place for the new sensor and I will check this as well. Excellent instruction, especially regarding how to remove the height adjusting knob which would be almost impossible to guess!
Thanks man. Your video saved my robot. I disassembled it and found the broken wire at the front sensor and replaced it. Now, the mower is working fine again. Great
It is always good to know how to repair. Although next time: you actually only need to unscrew the sensor (4 screws) and wiggle out the cable from the bottom… :) My question to you: I have to replace a cable and wonder what sort of cable it is.... It is not a copper cable. What did you use?
@@eblita3698 Hi there. I just jused one of the cables from my arduino-tinker-projects. But - just today - it broke again (after having it repaired two times already). I think i will have to replace the sensor completely now. I hope i'll be able to buy it somewhere.....
And thanks for the hint with the sensor-Screws ;-)
Hi gsbox, -though next time: you actually only have to unscrew the 4 screws at the sensor and then wiggle the cable out from the bottom…. much easier. I have a question: will you tell me what kind of cable did you used? I see it is not a copper cable…..
@@gsbox1976 Oh, bad luck. I hope you'll have your robot up and running soon!
Stort tack för instruktionen. Funkar klockrent! Vad man bör tänka på är att trycka fast det nya kabelpaketet på "rätt håll" så att man inte behöver vrida kablarna när sensorn ska skruvas fast igen. Det misstaget gjorde jag men orkade inte gå hela vägen tillbaka igen. :) Det får bära så länge det går. Suverän film!
Very helpful! Good walkthrough, excellent decleration! Thomas from Lemgo!
I did the layout and installation by studying the on line videos Husqvarna had on the web ua-cam.com/users/postUgkx2KDztGvdU79XTmlqIMSUyPq8CjprGJOR also recommended it When I started the unit it stated it would take a few days to learn all the spots in the yard. So I thought it was just finding the areas till I noticed it was cutting. It is so quite you don't know it is cutting.
well done just looking for a way to replace my front wheels now i know how to take it apart thanks!
Tack!! Väldigt bra och informativ film. Hjälpte mig igenom ett hjulbyte precis.
Great video, thanks so much for posting. Saved me a ton of time figuring out this repair on my Landroid.
My out of bounds error experience. First thanks for the video, sure helped getting it apart. Mine started one day about a month ago with the outside working area error. Reset it and it worked again. This went on for a couple days and then the error was permanent. Looked at the wiring harness to the front sensors and it did not look so good. Took it apart and removed the front sensor and charging assembly. I could not find any broken wires but I replaced it anyhow. While I was in there I replaced the lcd display since that had not been working right for awhile, Chinese characters or blank once it was on a few seconds. Put it back together but the same error, permanent out of boundary error, at least the display worked again normally. I think now wtf? I'm thinking maybe weak signal from the base station. Green light looked good, steady on green, flashed when I disconnected the wire, steady green when connected again. Then I decided to get a separate wire about 20m long and hooked it up instead of the permanent wire. Laid it on the ground in a big loop in the yard. Put Harry in the middle and no error and it worked like a champ, Again wtf? So I start thinking about the splices of wire I soldiered in to adjust the boundary several years ago, my wire has been in 6-7 years. Since it rained here a lot in August I'm thinking maybe one of these splices got wet through the heat shrink I used to insulate the wire and is grounding out the signal. Ripped all these places up and redid them, no luck. So now I get a box of wire and I ripped out all the original wire. One place where I pulled it up separated very easily. This spot was near where moles were digging and the wire ends looked chewed or scrapped from the moles, frayed. We have a lot of moles here in Germany and the mower keeps them out of the yard but they dig around the boundary. So it looks like they damaged the wire but not enough to cause the green led to flash but enough to cause the errors. After installing a totally new wire Harry is working just fine now. I bought my parts online at letmerepair-direct.de
Thank you so much for at great walkthrough. You saved me 7k Danish Kroner for at new robot. Mange tak fra Danmark
Thank you for your video, thanks to you I was able to change the charging block which had a cut wire, thank you very much it helped me. my robot charges perfectly, but now it no longer wants to leave its base, it moves back 50 cm and stops then beeps constantly. I tried to start it outside its base and it's the same thing. maybe I made a mistake when going back up? the front right connector seems out of order, via the robot screen but the block is new!
Mycket bra video, har tyvärr fått byta frontsensor två gånger på min de senaste 3 åren för att de tunna kablarna till laddarbläcken bryts av, verkar vara dåligt dimensionerat (eller dålig kvalitet, kanske båda) kablage. Bra med en tydlig guide så att man lätt kan se hur man ska göra. :-)
Great video and great work !!! Can you tell me if there's a way to test/measure the functioning of the left and right sensors ? I'm not sure mine are working ok or not. Many thanks !!!!
Hi and thanks for your appreciation! Unfortunately I do not have any idea about how to test/measure the functioning. But if it begins to leave outside the electronic fence I guess it is a signal of them not working properly.
Tack för denna!! Hjälpte mig mycket 🍺🍺
Kul att du gillar min video. Tryck gärna på prenumerera knappen 😊
Tak for en bra Video. ! Hvilket fell hada Worke Landroveren
Felet jag hade var att den inte stannade vid gränskabel utan fortsatte utanför.
Tusind tak for en god video.
Nu er jeg klar til at bestille en ny sensor og fikse vores Landroid.
Godt nytår :-)
Hilsner fra Jan - Danmark.
Thanks for sharing, i managed to fix ours today with the help of your video.
Jag tackar så mycket för denna detaljerade video. Exakt samma fel på min robot. (En korkad lösning från början) Jag ska beställa en och byta så snart det går.
Bra jobbat, tack igen! :)
I was actually able to repair my landroid by watching this video! Thank you so much Kenneth!
I do have one problem though. I'm not able to turn the blade height knob to anything lower than 55mm. Did I mount it wrong?
Thanks again :-)
Hi, nice to hear that my video has been a good guide for you.
Yes, the height knob should work as usual so I'm afraid you have to re-do some of the steps, starting with de-mounting. I made the video a couple of years ago so I do not remember all details of how I did it but I remember that one has to be careful remounting the knob. Do under way tests of it's correct function during re-mounting.
@@KennethSteen I got it now! I forgot to tighten one of the screws 🤦♂
Tack för en bra video. Monterat en ny frontsensor, men maskinen är fortfarande utanför arbetsområde. Har ni några mer tips?
Hej kul att du gillar min video men tråkigt att bytet av frontsensor inte löste problemet. Nej jag har nog inte någon idé om vad som då kan vara problemet.
Men eftersom du gillade videon så får du jättegärna prenumerera på min kanal. Det kommer fler videos du kan ha nytta av 😃
Grymt video, kanske jag kan rädda min gamla maskin också, som strular, räckte inte med batteribyte!
Great tutorial. Thank you very much!
Welcome to subscribe🙂
Great video ! Fully instruction, well done, Thank's
Thanks for this great job! But tell me please... What was the "strange things" that your robot did? Mine is slightly turning right and left just like when it find his boundary wire, but it does that in the middle of my garden, with no wire below it to be sensed by the sensor... Pretty crazy... 6 years of use.
My problem was it went outside the boundary.
@@KennethSteen Thanks my friend. I could fix the wire following your tips and mine worked fine since last time i wrote to you. Like a year. Yesterday it started to run in circles, like 3m diameter. I can see that one wheel is spinnig faster than other, but i don't know if it's a motor issue or circuitry issue. If you guess what may be happening, i'll gladly take your advice. Other than that, as soon as i fix it, i'll share it here, since you may face the same issue someday. Thanks!
@@dayangolanski1250 Hi, that is strange behaviour. I have not encountered that problem myself but I would first check that there is no dirt that hinders the wheel to spin.
Got the same issue, did you solve it?
Thank you for that Video, it helped me a lot.
But: Where do I get a new such front-loading-device?
Hi, thanks for your comments. I bought mine at clasohlson.com. Swedish site.
Just wanted to say: had a problem with Landroid after rinsing the wheels with water. The keyboard stopped working. Remedy: REMOVE the battery IMMEDIATELY so that no more electricity flows and wait until everything has dried up. Then we went again. Recommendation; be careful when rinsing, especially from below. The keyboard connector should not be adequately protected against water. I will look at it when the opportunity arises and seal it accordingly.
My keyboard has died (didn't rinse it with water, it just has keys that stopped working... One of which is part of the PIN). Did you end up replacing yours, and if yes, where did you buy it from?
hello, thank you for your video, first of all, someone gave it to me because it is broken. I would like to know where i can find the exact reference ? I see yours is the WG791E, where can i check which one is mine ?
On the back of the WORX
I changed sensor thanks to your video but my landroid it.keeps saying out of area...any idea?
Hello, great video. My Landroid stops with the error "elevation" I discover that it is the sensor on the side. The robot stops when the cover which has a magnet lifts from the metal part. Any idea what I could do to keep it going without stopping? Thanks
Hi, thanks for consulting me in this matter but unfortunately I´ve not been into that problem (yet) and do not have a clue.
@@KennethSteen No chance for me ^^' Thank you for your response and thank you for your help.
I have the same error ‘lifted up’ and would like to follow any news on this too
Thank you for this video. It looks like there is a little space in the front corner(s) above the caster wheels. Do you think that their is enough room to place a gps tracker? Do you remember about how much space might be available? Thanks again.
Oh, nice idea, but I do not remember...
Thanks for the great video - Where do you get the spareparts from - i probably need a new keypad?
I bough the sensor at clasohlson.se
Good job! I have problem after doing all this though. It says trapped.. Do you know why?
Hmm, could it be so that one of the wheels are stuck...? Or could it be that the black cover is not remounted correctly. It might give the machine the signal that it has run into something and that it thereby thinks it is stuck.
Maybe, I will check it soon. Thanks for the tip
@@KennethSteen Well, i have checked everything, even changed the trapped sensors. Magnets seems fine.. but still its trapped.. and the issue is that i cant reset by pushing 0. Its not working. The button is working, have tried it in the "date" section just to see if there is a problem with the keyboard.. but no. Im lost.
@@KennethSteen Can you maybe show me the sensor display to see what sensors are active before start. cheers
Hi Kenneth. You were a life saver. Thank you from Denmark :-) (Klippetøff is genopstået fra de døde igen)
What kind of error gives you the broken sensor apart from getting stuck on obstacles? Mine Wg794e keeps turning around and then it stops giving different errors every time...blocked wheel, out of aerea, stucked...etc...main problem is i got that from China and apparently different connection on shock sensor..at least the shop told me this and they didnt fix that..any help?
He sometimes passed his electric fence and "ran away"
Your comment "make sure the pins holding the silver hatches are in their places" is confusing to me.. Whichs pins are they ? Are these the long round pins that hold the latches and the springs ? I also read something about the two metal parts that are in the frame needing to touch with some pins from the assembly ? Thank you so much !
Hmm, I do not really remember. Been quite a while now since I made the video. Sorry.
You don’t need to disassemble the whole Mower! Just drag the rubber out of the bottom and the Plug Connection will follow out of the hole. You can simply unplug and have the Sensor unit free to work.
My wg794 landroid always makes right turns at the end of the cut , but never makes left turn. Do you know what the problem is. Thanks
is there a source for parts?
Thanks a lot for this brilliant guide 👍👍
Thank you for this, sincerely.
Thank you so much for your video! "Little MoJo" is running good again :)
Hello. I liked a lot of your video. I think I have the same problem with my robot. I searched to buy the bundle of cables in question but unsuccessfully. Would you send me a link from a site in which they offer it? I will be very thankful.
Tack för informationen
Hej Kenneth hvilken af fejl gjorde din Work? Min er nemlig begyndt med at skrive uden for område når den er 1 meter væk fra ledningen som går rundt i kanten af haven
Den började åka utanför sitt område lite då och då
How long did it take for the problems to occur?
A couple of years I would say. Do not remember exactly.
Changed the sensor sucessfully but still see two x'es that mean it's still not working :-( Any suggestions?
Like your video where do you get your parts from.
www.clasohlson.com/se/c/Brand/WORX
Where dit you buy the black piece for charging...mine is broken and the company of worx can not provide this piece
Hi, I bought it at www.clasohlson.com/se/Frontsensor-Worx-Landroid,-E1-(2016-)/p/Pr513256000
Seems to be in stock also now. Good luck (let your web-browser translate the Swedish into english)
Hi, nice video! It seems that my front end sensor is working. My problem is that the Worx Android stopped charging. I took the battery out and could charge it, but it does not charge when coming to the home base. The light turns red, but after a while goes off, before turning red again. So it seems there is a bad contact between the pins from the home base to the battery. Would it help to change the front end sensor?
Hi, I would look for a reset instruction (I do not remember if I´ve seen such) to reset the Landroid. Also check that all the thin cables are ok (the ones in the front sensor where the pins for charging enters the Landroid).
Hi, where did you find the replacement?
Clasohlson.se
www.clasohlson.com/se/Frontsensor-Worx-Landroid,-E1-(2016-)/p/51-3256?gclid=CjwKCAjwqpP2BRBTEiwAfpiD-xqqm9qKHrvoAs4RcmmuZNsLWs7JXG1lqkp4r6Jy7-pbLsSLCOKfwhoCL-EQAvD_BwE
Where did you find the part? I can’t find one.
I bought mine here www.clasohlson.com/se/Frontsensor-Worx-Landroid%2C-E1-%282016-%29/p/Pr513256000
@@KennethSteen Thank you
I conect both conection plugs but still with 2 x on the lcd panel. Does anybody know what could be?
I have the display stuck on the writing "jammed press 0" can you help me?
Sorry, I do not know but try resetting by disconnecting the battery for a couple of minutes.
Bonjour, j'ai l' erreur "élévation" qui s'affiche sur l'écran et la tondeuse s'arrête. Sur l'écran il est écrit appuyer sur "O" Que faire ? j'ai la worx wg 754e.merci
Io ho un problema.quando il robot e sulla base pa.puce passa da rosso a verde e sul display mi scrive fuori area.poi socompare. Il red torna rosso e via di seguito.ho cambiato blocco sensori , batteria ....circuito della base e alimentatore. Stesso problema cosa puo essere?
Wo kann ich die Frontsensor bestellen?
Hi, I bought mine here www.clasohlson.com/se/Frontsensor-Worx-Landroid,-E-(2014-15)/p/51-3258?gclid=Cj0KCQiAnKeCBhDPARIsAFDTLTL0NXpcDLfO1GPLn4J_Fyi7v5nTA2ZjilQRBgMXSDNXihz-mygiWRUaArUJEALw_wcB
If you liked my video I would be very happy if you want to subscribe :)
bonjour je n ai plus moyen d allumé mon robot worx landroid wg791e j ai changé la pile de l écran se trouvant sur la platine du circuit imprimé a l 'intérieur (cr1225 3v ) servant pour l écran celle ci était morte 0,5v depuis plus moyen d allumé mon robot !!!! NB/ quand je le mets sur la station sans la batterie la lampe verte vire au rouge j appuie 2secondes l écran s allume et m'indique batterie en charge 0a100%puis me dis code incorrect au revoir puis il s'éteind !!!! si je remet la batterie et que je fais la même opération il ne s'allume pas !!! même si je le fais hors de la station plus moyen de l 'allumé plus aucune touche ne fonctionnent l'écran ne s'allume pas que faire NB ; la batterie est chargée nouvelle batterie merci pour votre réponse si il y a !!!
Stort tack!
COMMENT REMPLACER LA PILE INTERNE DU WORX WG754E
Is this language called SWEnglish??
For older models, checkout worx-reservedeler.no/wp-content/uploads/2020/06/Bytte-frontsensor-eldre-M-modeller.pdf