Not gonna lie, this is probably the most detailed 'how to' video I've ever watched. I realised quite quickly that this didn't relate to my issue, and I still finished the whole thing 🤣
Probably the best channel on UA-cam for detailed information regarding fault codes. Thank you so much for providing a detailed explanation on how and why this fault code occurs. I've had numerous codes occur over the past 6 weeks until this code appeared. My vehicle burns through an excessive amount of oil, I have to constantly top it up before oil changes.
Your personality and your method of presentation make it easy to watch. Thank you for all the information you gave on the topic. I started changing these this morning on an '06 F150 5.4l 3v Triton. The vct's are down in a hole with a small bolt holding them in and a rubber seal on top. The passenger side went ok. But the driver side little bolt is screwed in so tight it's ridiculous. Maybe a guy could break it loose but it is almost like it was put in with an impact wrench. So my question is...how can I break this little bolt loose without messing up something? Thanks for your help...whoever answers. Jesus bless.
black smoke means too much fuel... burning oil is blue smoke. One smells like unburned fuel and the other one like burnt oil. Either way, not a VVT solenoid.
Excellent detailed testing at 12:30. I have a pesky P0011 on 2007 Nissan Xterra 6 speed manual 112k miles. I do not want to bust open the timing cover and do a timing job if not needed so that test will help determine if the problem is with the cam phaser. Thank you
Great video; thank you. Though I've searched UA-cam on replacing the other bank and nobody has shown the process and headache of removing the plenum to gain access to that one. I was hoping you would show that process on the 3.5L Nissan Altima.
Hi. I have a P0011 on my 2011 Infiniti G37s. It started after I changed oil after not changing it for a long time. Like 9000 miles. I changed oil again, replaced VVT solenoids, and replaced a couple of sensors. The car runs ok when I reset the code, but it reappears every other start and the engine obviously goes back to limp mode. Technicians at some body shop tell me I have to change a sprocket and timing chain and want to charge 30 hours of work at $150 just to get to it, without diagnosing the actual problem. What would your advice be in my situation.
Quick question - when completed and the codes have been reset, wouldn't you need to do a Vanos adaptation reset to ensure the values are within tolerance? Great video by the way!
For the rear VVT there's not need to take out the intake manifold, just move to the left that black hose full of cables and use an extender with a ratch. It will take less than 10 minutes.
My wife has a LR discovery sport and her CE light just came on. Codes are P0000A, P0011, P000B and P0014. I checked her oil. It was low. Is this a DIY job or should I take it to dealership?
I bought a used truck & it had the same code. It was apparent that previous owner did not change oil often enough. When I took the oil cap off, you can see the burnt oil residue on inside. So, I added oil cleaner and drove truck awhile. Then changed the oil. Once changed, removed the solenoid and soaked it overnight in diesel. Then I tested it by hooking wires to battery. The solenoid plunger moved. Reinstalled. Engine light is still on, I think I can reset by adding a 1 Watt 10 ohm resister to battery. So, was it wise to add oil cleaner first before installing new solenoids? It's a quick fix till I buy new ones.
Hello Dear, thanks a lot for explaining it very well I got important information about facing a problem. Actually, I have " Hyundai Accent 2013 car" I am facing the problem " the Oil light is blinking, when I cross around 20 KM, the light blinking when I stop only not while I'm driving" Anyway, I checked my car by computer tester and I found this error " P0011 'A' Camshaft Position Timing Over-Advanced Or System Performance Bank 1" Please tell me what must to do.
Thank you so much I did everything you said and it worked but my battery warning is still lit on my dash but it’s not weak the battery and it doesn’t need a jump how do I reset that
So does changing the oil fix it ? Admit i let mine go a bit longer then i should of,just got it changed.im afraid to scan again 😢 they didn't give me any quote on a solenoid. So confusing.
You either advance the timing or retard the timing, I know that last word is a trigger word for some sensitive snowflakes but it's accurate for what you are trying to describe, do not let their overly sensitive feelings stop you from stating the facts using the best and most accurate words to describe what is happening. Great educational video by the way!
Good day, i have a chevy cruze. I get p0011 error. Replaced the intake cam due to sensor pickup that broke off. Then i replaced the solenoid valve. Still get p0011 error after driving for about 15km. When the car is cold and i start it the lifters make a noise then it goes quiet. Must i change my vvt sprocket. Thank you
My oil is still nesrly ambet and at max yet my dash says "get engine serived". My 2003 Saturn Ion purrs like a kitten. I take care of it myself thougj i had a mechanic replace the ECM recently because as a DYI'ER I must know my limitations. There is no more than 1200 miles on my engine (5/30 Pennzoil Platinum - nothing but the BEST)! Why do i get this indicator? Thanks. David Alberta
I got an oil change and they didn’t know what service engine soon indicator light was for. It is diff than check engine light. Went to autozone and got a pp0011 code and they didn’t know what it was for. After he pulled out reader the light went off and reset itself. Another thing neither car place knew how to do. Mine is Mitshubishi
I'm having similar issues. I had vvt codes after running out of gas. Turned out to be bad intake. I changed them both but now I have a misfire in cylinder 2. And the intake code p0010 still there.. Changed oil and filters and air filter. Worried to start my car again with the misfire.
Here's the gig (ignition on / engine off) (Gm 3.6 over Advanced exhaust) When you plug in all four actuators Three of the actuators engage and when you start the engine it runs absolutely terrible. The fourth solenoid has power but does not activate the solenoid but the solenoid is good cuz I checked it manually. But with the fourth one plugged in and the other three solenoids unplugged the engine runs perfect cuz three of them are not engaged. plug any other actuator in and the engine runs pathetic
Is it possible that these solenoids will need to be replaced without a code? I have a blue driver and my vvt was showing live data and it was marked with a yellow exclamation amd the other vvt were green. I have a rough idle.
Hello I like your videos but I have a question. I have a humming kind of grinding noise at lower speeds but the humming throughout speeds on the left front tire wheel. I thought it was the bearing but when I turn right it goes away and when I drive on the left side of the road that is banked maybe four or 5° so that the left side of the wheel goes down rides on the lower part of the bank the noise goes away. But the alignment was recently done and it said it was good within spec and after the alignment and still does it I still have all the same symptoms. Can it still be the bearing that is cracked in some place or is the bearing like cockeyed within the hub but we'll still go straight.
Engineers design car, spec a maintenance interval for all serviceable systems, end users don't do maintenance, say the car is horrible. Engineers redesign systems to be "sealed for life" and use "lifetime fluids". Problem solved right?
I got a problem with my secondary air injection system and the pigtail that’s hooked up to it isn’t getting power any idea of how to fix it please reply
2007 Hyundai Sonata... check engine code P0011... oil is fine... bought brand new vvt solenoid (specific for my car)... easy install, now the car idles very high... tried 4 straight days, hoping it would adjust, but same result... anybody have solutions...thanks
Can anyone help? I have the P0011 code. I took it too autozone and it told me that it was the timing plate(very unfamiliar with this part) I know it’s a cover of some sort. But I have no problems with the car, no rattling, slapping, or any other odd noises, no trouble starting or accelerating, or idle issues. Any help on this? I don’t want to take it and spend more money then I have to, (just purchased vehicle)
√ *Watch the Video*
√ *Buy The Part at 1A Auto* 1aau.to/m/Visit-1AAuto
√ *Do it Yourself*
√ *Save Money*
Thank you vary informative bless you keep up the good work
New big changes no New Breed changes
N u be bed changes
This woman is a well experienced mechanic, she can make any engine sing in harmony.
Not gonna lie, this is probably the most detailed 'how to' video I've ever watched. I realised quite quickly that this didn't relate to my issue, and I still finished the whole thing 🤣
“Pretty excited about a misfire” 😊 So glad you love your job and make videos like this for us…
If i ever need someone to fix my car, you will be the first one I call. 👍👍
Probably the best channel on UA-cam for detailed information regarding fault codes. Thank you so much for providing a detailed explanation on how and why this fault code occurs. I've had numerous codes occur over the past 6 weeks until this code appeared. My vehicle burns through an excessive amount of oil, I have to constantly top it up before oil changes.
An amazingly detailed instructor I hope there are more videos lead by her because she is fantastic
Excellent vid and your mechanic did a great job explaining the process.
Very details and great diagnostic. This video so far are the best I’ve seen. I wish you live in my city, I’ll definitely use your service. Thank you
I am beyond just impressed, I agree with others comments, this lady is by far the best mechanic and teacher ever! (Sure wish she lived in our area)
I loved watching someone who LOVES their work....she really does!!!!
👏🏼 by far the best diagnostic video. Very focused. Easy to follow w great info.
Your videos helped me sort my cambelt, saved my engine, thank you
Great, great video. You are a great teacher and technician.
I was happy to see a woman doing this video!! You explained things really well. Just wanted to send you a high five!! You go girl!! Katrina
Your personality and your method of presentation make it easy to watch. Thank you for all the information you gave on the topic.
I started changing these this morning on an '06 F150 5.4l 3v Triton. The vct's are down in a hole with a small bolt holding them in and a rubber seal on top. The passenger side went ok.
But the driver side little bolt is screwed in so tight it's ridiculous. Maybe a guy could break it loose but it is almost like it was put in with an impact wrench.
So my question is...how can I break this little bolt loose without messing up something? Thanks for your help...whoever answers. Jesus bless.
Your video is the best demonstration about vvt solenoid testing. Thank you very much may jehovah god bless you.
I love the way u explaining how to diagnose, I appreciate your videos and love watching them
This video is perfect timing, my car has been burning oil (oil loss with black smoke). Now I know what my next steps should be. Thanks 👍
black smoke means too much fuel... burning oil is blue smoke. One smells like unburned fuel and the other one like burnt oil. Either way, not a VVT solenoid.
This is one of my favorite UA-cam video. Very informative 👍👍👍👍
+E Lab Thanks for the feedback!
Excellent detailed testing at 12:30. I have a pesky P0011 on 2007 Nissan Xterra 6 speed manual 112k miles. I do not want to bust open the timing cover and do a timing job if not needed so that test will help determine if the problem is with the cam phaser. Thank you
+@PaulHenreid Thanks for checking us out! 1aau.to/m/Shop-1AAuto-c
Hi, Sue! Nice to see you again. :-)
Take care and have a great weekend!
I love the lady. Who can fixed the car. 💪💪💪
Great video; thank you. Though I've searched UA-cam on replacing the other bank and nobody has shown the process and headache of removing the plenum to gain access to that one. I was hoping you would show that process on the 3.5L Nissan Altima.
Hi. I have a P0011 on my 2011 Infiniti G37s. It started after I changed oil after not changing it for a long time. Like 9000 miles. I changed oil again, replaced VVT solenoids, and replaced a couple of sensors. The car runs ok when I reset the code, but it reappears every other start and the engine obviously goes back to limp mode. Technicians at some body shop tell me I have to change a sprocket and timing chain and want to charge 30 hours of work at $150 just to get to it, without diagnosing the actual problem. What would your advice be in my situation.
"Box Office" lady is back. Love her videos
Love your enthusiasm and expertise!
Just love your thorough explanation!
Learned something new everytime thank you.
Quick question - when completed and the codes have been reset, wouldn't you need to do a Vanos adaptation reset to ensure the values are within tolerance? Great video by the way!
Great video lady watching this from Jamaica 👍👍
Good diagnostic tech!! Knowing is half the battle.
Very good communication given, I love et, proper instructions, on subject matter at hand, 😊 👍 good job.
For the rear VVT there's not need to take out the intake manifold, just move to the left that black hose full of cables and use an extender with a ratch. It will take less than 10 minutes.
Great instructional video thank you
My wife has a LR discovery sport and her CE light just came on. Codes are P0000A, P0011, P000B and P0014. I checked her oil. It was low. Is this a DIY job or should I take it to dealership?
You made this helpful post understandable. Thanks Sue.
+unite entierly Thanks for checking us out! 1aau.to/m/Shop-1AAuto-c
Lady, you are the best!
Makes sense. I've seen VVT screw up and over time causing the PCV to stick and blojob oil out of the engine.
You are Awesome lady you've helped me in a mighty way 👌
This helped me out allot
15 Hyundai Sonata sport 2.4L codes P0010 P0011 and where the solenoid located. Thank you for your assistance
Mine was low light came on had no boost low power, oil was low topped it up all seems fine now keep an eye on it see if its sorted
Thanks for the Great advices love the way you Teach BLESSINGS TO YOU AND YOUR LOVE ONE'S AMEN 🙏
I bought a used truck & it had the same code. It was apparent that previous owner did not change oil often enough. When I took the oil cap off, you can see the burnt oil residue on inside. So, I added oil cleaner and drove truck awhile. Then changed the oil. Once changed, removed the solenoid and soaked it overnight in diesel. Then I tested it by hooking wires to battery. The solenoid plunger moved. Reinstalled. Engine light is still on, I think I can reset by adding a 1 Watt 10 ohm resister to battery. So, was it wise to add oil cleaner first before installing new solenoids? It's a quick fix till I buy new ones.
I absolutely love her.......she is definitely on her A-Game. ❤❤❤
+tpridgen11 Thanks for checking us out! 1aau.to/m/Shop-1AAuto-c
Hello Dear, thanks a lot for explaining it very well I got important information about facing a problem.
Actually, I have " Hyundai Accent 2013 car"
I am facing the problem " the Oil light is blinking, when I cross around 20 KM, the light blinking when I stop only not while I'm driving"
Anyway, I checked my car by computer tester and I found this error " P0011 'A' Camshaft Position Timing Over-Advanced Or System Performance Bank 1"
Please tell me what must to do.
Love it😁we need more of her
Excellent and informative
Excellent video ,well explain 👏bravo 👏
Thank you so much I did everything you said and it worked but my battery warning is still lit on my dash but it’s not weak the battery and it doesn’t need a jump how do I reset that
Will you get p0081 code for either solenoid? Or is p0081 specific to a bank?
Did u fix the misfire?
So does changing the oil fix it ? Admit i let mine go a bit longer then i should of,just got it changed.im afraid to scan again 😢 they didn't give me any quote on a solenoid. So confusing.
Great explanation! Thanks you.
+Dennis Clapp Thanks for checking us out! 1aau.to/m/Shop-1AAuto-c
Exellent diagnostic , Saludos desde Dallas, tx 👏👏👏👏👏
Good video. Thanks!
Great job , thank you
You either advance the timing or retard the timing, I know that last word is a trigger word for some sensitive snowflakes but it's accurate for what you are trying to describe, do not let their overly sensitive feelings stop you from stating the facts using the best and most accurate words to describe what is happening. Great educational video by the way!
The thing i found is the solenoid test good when cold . Put it back on the engine when hot for 25 min. It stop working. check for this.
Good day, i have a chevy cruze. I get p0011 error. Replaced the intake cam due to sensor pickup that broke off. Then i replaced the solenoid valve. Still get p0011 error after driving for about 15km. When the car is cold and i start it the lifters make a noise then it goes quiet. Must i change my vvt sprocket. Thank you
Thanks for this confirmation!
Presente cordial saludo desde Navoyork Sonora México
Now I know what’s causing that slight clucking sound on my car. VVT Solenoid!
Amaizing job.
Thanks, God bless you.
Great vide..thanks need it!
Should I be using synthetic oil for my Nissan Versa 2014? I have the code p0011
Excellent topic 👍
Does this cause a lil knocking ?
My oil is still nesrly ambet and at max yet my dash says "get engine serived". My 2003 Saturn Ion purrs like a kitten. I take care of it myself thougj i had a mechanic replace the ECM recently because as a DYI'ER I must know my limitations. There is no more than 1200 miles on my engine (5/30 Pennzoil Platinum - nothing but the BEST)!
Why do i get this indicator?
Thanks.
David
Alberta
Awesome video
I got an oil change and they didn’t know what service engine soon indicator light was for. It is diff than check engine light. Went to autozone and got a pp0011 code and they didn’t know what it was for. After he pulled out reader the light went off and reset itself. Another thing neither car place knew how to do. Mine is Mitshubishi
Great job!
This was very interesting 👍🏼👍🏼👍🏼
Good job mam …
I'm having similar issues. I had vvt codes after running out of gas. Turned out to be bad intake. I changed them both but now I have a misfire in cylinder 2. And the intake code p0010 still there.. Changed oil and filters and air filter. Worried to start my car again with the misfire.
Here's the gig (ignition on / engine off) (Gm 3.6 over Advanced exhaust) When you plug in all four actuators Three of the actuators engage and when you start the engine it runs absolutely terrible. The fourth solenoid has power but does not activate the solenoid but the solenoid is good cuz I checked it manually. But with the fourth one plugged in and the other three solenoids unplugged the engine runs perfect cuz three of them are not engaged. plug any other actuator in and the engine runs pathetic
Is it possible that these solenoids will need to be replaced without a code? I have a blue driver and my vvt was showing live data and it was marked with a yellow exclamation amd the other vvt were green. I have a rough idle.
Great info.
Hello I like your videos but I have a question. I have a humming kind of grinding noise at lower speeds but the humming throughout speeds on the left front tire wheel. I thought it was the bearing but when I turn right it goes away and when I drive on the left side of the road that is banked maybe four or 5° so that the left side of the wheel goes down rides on the lower part of the bank the noise goes away. But the alignment was recently done and it said it was good within spec and after the alignment and still does it I still have all the same symptoms. Can it still be the bearing that is cracked in some place or is the bearing like cockeyed within the hub but we'll still go straight.
I feel that the tire is riding on the inside of it like cambered top tire in, so that when it rides on a bank road it rides at the correct angle...
Should I disconnect the battery before replacement?
Engineers design car, spec a maintenance interval for all serviceable systems, end users don't do maintenance, say the car is horrible. Engineers redesign systems to be "sealed for life" and use "lifetime fluids". Problem solved right?
Word on the street is always buy OEM? 🤔 I did and still throwing same code
I got a problem with my secondary air injection system and the pigtail that’s hooked up to it isn’t getting power any idea of how to fix it please reply
2007 Hyundai Sonata... check engine code P0011... oil is fine... bought brand new vvt solenoid (specific for my car)... easy install, now the car idles very high... tried 4 straight days, hoping it would adjust, but same result... anybody have solutions...thanks
I keep up the oil changes and I scanned came that code , i recently replaced the engine gasket , why still comes up !
Hi I am Aurang zaib from Pakistan and you? Good work I am waiting your answer
Is poo14 the same
We plan to travel for thanksgiving and now we got stock rpm high
Well explained 👏 more like you be helpful , Dude like me ( fixt. ) oil leak...👍
Help!! A have P0011 and the problem is not VVT, a tried it. Somtimes its code P000A but most of the time P0011. What to do?
Is FULL Synthetic oil actually 100% synthetic or not?
I enjoy watching her
Can anyone help? I have the P0011 code. I took it too autozone and it told me that it was the timing plate(very unfamiliar with this part) I know it’s a cover of some sort. But I have no problems with the car, no rattling, slapping, or any other odd noises, no trouble starting or accelerating, or idle issues. Any help on this? I don’t want to take it and spend more money then I have to, (just purchased vehicle)
This Nissan Models, I think its Nissan Altima, has rust problems, they rust under the car very fast, especially the carpet, and seat area.
Nissan VQ35 is a great engine, that is if she is full of good quality oil and not hooked up with a Jatco CVT
It nice explaination
Where is the vvt selnoid location in 2015 Hyundai sonata sport 2.4l?
So that code could just pop up because I need a oil change