Building a Wood Laptop Table / Stand / Desk Quick DIY Project
Вставка
- Опубліковано 20 лип 2019
- Building a Wood Laptop Table / Stand / Desk Quick DIY Project
I felt like a bad infomercial every time I used my laptop on my lap so I had to do something about it. A quick trip to the hardware store and a few bucks later I had the small requirement of parts.
I grabbed a piece of pine 16" x 48" to use as the top. I then used red oak for the legs. I just figured it'd be a nice contrast and I think I was right. The nuts, bolts, and washers were standard 1/4" x #20.
I cut the top down to 13" x 20" and it's working just fine. I definitely could've gone a little wider to get better space for using the mouse, but it'll do for now.
The legs were cut down to 9". Not on the video is me cutting angles at the top of each leg. This was to ensure unrestricted movement of the legs when opening and closing them. You'll see what I mean.
Don't rag on me too hard for using 5-minute epoxy. :) I needed something that would cure quickly and be strong. It really is holding up very nicely. Very strong connection. I did throw some brad nails into the top, through the border. I did this on the inside and at an angle so you wouldn't see them. Double protection from failure in my eyes!
After it was all glued and cured, I simply put the nuts in the predrilled holes and tightened until I had the friction where I wanted.
All in all, an easy but fun little build! And useful!
Don't forget to Like and Subscribe if you enjoyed and would like to see more!
Green Hill Graphics, LLC
Birdsboro, PA
www.DecalsNStickers.com
/ greenhillgraphicsllc - Навчання та стиль
Check it Out!! Watch me Build a Wood Laptop Table / Stand / Desk Quick DIY Project!!
For anyone asking, here are the dimensions I used
Tabletop - 13" x 21" x .75"
Fame for the legs - (2) 19" x 1.5" x .75" and (2) 10.5" x 1.5" x .75"
Legs - (4) 8" x 1.5" x .75". **If I were to do it again I would make the legs slightly longer, possibly 10".
The brace that goes between the legs - 9" x 1.5" x .75"
Hope this helps!!
If you suggest to make the legs 10" then I would need to make the frame for the legs slightly longer as well or the legs would not fold inward. What length would you suggest I make the frame to fit the 10" legs?
@@carlosbergante4316 Hey Carlos, honestly didn't think of that when I wrote it.. I was just thinking for comfort to raise the table up a little bit. But, if I were to make one again, I would probably just increase the top to 24". That should accommodate 9" or even 9.5" legs, plus give you a bit more room on the top. For 10", maybe bump it up to 25"-26".
Awesome! I'm an old guy that's gone through stage 4 Cancer and stage 3 kidney disease and I've never been the same. Making a lap table like this is exactly what I need for when I'm reading and writing! Thank you ! 🇺🇸🙏❤
You almost look like David Gilmore from Pink Floyd! Super nice job I will make one for the grandkid! Thanks😊
Haha. If only I could play the guitar half as good as him. Thanks!!
nice, got my wood . ready to start mine
love the vibe 😍
Great job!
easy to make at home nice DIY definitely worth to give it a try
Thanks! It's been a few months and still holding up just fine! Quick afternoon project!
Thing of beauty
wow nice
Nice job
+gk diy thank you!!
Thanks.
buen video muchas gracias por compartir tus habilidades
Thank you!!
Excelente
Looks good. What angle did you cut the legs that meet the floor? The angles from the top of each leg look like 45s. Thanks!
Thanks!! Yeah they were cut at roughly 45ish so they’d sit flat when folded out.
Super sekali
Do you have plans/instructions with measurements available?
I enjoyed the bgm. What's the title?
What angle do you cut the legs?
Good job. Could you pass me the measurements please? I want to build one just like it for me.
Greetings, from Buenos Aires, Argentina!
Hey! I did just wing it as I went to be honest. The top is based solely on the dimensions of MY laptop with a little extra.
Here is what I used -
Tabletop - 13" x 21" x .75"
Fame for the legs - (2) 19" x 1.5" x .75" and (2) 10.5" x 1.5" x .75"
Legs - (4) 8" x 1.5" x .75". **If I were to do it again I would make the legs slightly longer, possibly 10".
The brace that goes between the legs - 9" x 1.5" x .75"
Hope this helps!!
Anyone knows the music used in this video?
This is a cool build. Is there a reason you used epoxy over wood glue? Otherwise looks amazing
Thanks! Honestly it’s just pure laziness. I ran out of wood glue and didn’t feel like going out. Had epoxy on hand so I used that. 😉
Feeeeeeeeeeeeeeeeeeeeeeeeeeeeennnnnnnnnnnnnnnnnnnnnnnnnnnnnnnttttttttttttttttttttttttttttaaaaaaaaaaaassssssssssssssstttttttttttttttttttttttiiiiiiiiiiiiiiiiiccccccccccccccccccccccccccccccccccccccccc 99% , can you make with a wooden screws , Or wooden studds ( am not sure if this is the right term in Carpentary ) hope you got my question ........ Thank you. :)
What's the background music?
What is the total weight of the table?
Bgm- Time on our side by sebastian
Give it away . 😀
Are you the vocal from the Pink Floyd? :)
👍😀👍
deixa as medidas d
What is that hardware you used for the legs called?
They were just 1/4 in nuts and bolts. And some washers. Nothing special!!
Can you pls provide me sizes of wood needed? Thanks.
Hey! I did just wing it as I went to be honest. The top is based solely on the dimensions of MY laptop with a little extra.
Here is what I used -
Tabletop - 13" x 21" x .75"
Fame for the legs - (2) 19" x 1.5" x .75" and (2) 10.5" x 1.5" x .75"
Legs - (4) 8" x 1.5" x .75". **If I were to do it again I would make the legs slightly longer, possibly 10".
The brace that goes between the legs - 9" x 1.5" x .75"
Hope this helps!!
Hello! I really need something like this but different size like 25x20 can you build it for me. How much it cost?
If you are local to me, sure! I'm in PA.
@@greenhillgraphics I’m in NJ
Ya know they make wood glue. Lol. Nice build though.
Lol. I was wondering when someone would mention that. Ran out of wood glue and just didn’t feel like going back to the store. Pure laziness. Thanks Russell!!
Not enough height for bed or sofa usage ☝️
much better if you include the measurements....
Here is what I used -
Tabletop - 13" x 21" x .75"
Fame for the legs - (2) 19" x 1.5" x .75" and (2) 10.5" x 1.5" x .75"
Legs - (4) 8" x 1.5" x .75". **If I were to do it again I would make the legs slightly longer.
The brace that goes between the legs - 9" x 1.5" x .75"
Dude can you give me the materials you used here aside from the wood?
Hey! I’m pretty sure I just grabbed some 1/4” bolts and nuts with washers I had. That’s the only hardware.
Thanks dude did you use some varnish here?
Markus Villame no problem. I just used a couple coats of teak oil.
Thank you so much dude
But wait theres more.... call within the next 10 mins and well include.. not 1, not 2, but.3........
Haha. “Just pay separate shipping and handling”
I'm sure you can find awesome woodworking plans on woodprix
Toonami li ji op all in one table op on playlist stat li ji 8 7 design functions li op 9 0 a