it reads and executes a 7 milion line G code without a problem. I pause the file and resume in middle of it after tool change because of broken tool. No problem. Just have to wait 15 minutes until it reads the 3 million lines again :-")
Good morning, friend the 4 axis can be put as a slave of the Y axis ?. On the Y axis I have 2 motors. Or would it have to output an axis Y put 2 drivers one for each motor?
Hello i have bought a 4 axis DDCSV. I use artcam or vectric aspire. What post processor can I use for the ddcsv controller. I want to use it with a manual tool change. Thanks in advance. Mario
Pues entonces tienes que bajar el manual en pdf y traducirlo pagina por pagina usando el traductor de Google. No veo otra manera de programarlo si no hablas Inglés
Axis A, can be set up to Tangential cutter 360º. - In Mach3, in configuration must be activated in Rotational: ·Rot 360 rollover ·Ang Short Rot on G0 Can you do this on the DDCV1.1 console?
Setting of axis A (rotation) in Mach3 cdn.thingiverse.com/assets/a9/6a/03/49/a0/general.png cdn.thingiverse.com/assets/8b/d1/75/35/bc/Settings_Alt-6.png www.thingiverse.com/thing:1436870
Hi, I have the same controller but cannot open files, I can see the simulated toolpath but when i press start nothing happens, has something similar ever happened to you? everything else works fine
Boyan Silyavski thank you, I already updated the firmware with no success, is there some pre-operation check that the controller does? Could be a problem that I'm working in negative coordinates space? With the zero in top right corner of the plane
I work with Z0 on top of Z axis, which is the normal thing according to me. So lowering the Z is with negative sign. I think You will have to download the manual and check it line by line/the controller settings/ as it have happened to me to accidentally change a setting and then had to do that. It took me an hour but i figured my mistake. You willneed to be patient not to miss something. But first of all check as there is a setting which says if the controller is comanded by G code, so there may be the mistake, you could have switched it to 100% mmanual mode
No. But signal is strong and you can connect 2 drives to one axis output. No problem. Works perfectly. You will need a hard stop then on machine so you can bump manually the 2 axis there so they are square and then switch on machine. That simple.
I dont think you are actually upgrading the firmware. Its a software upgrade. I have that installed now. The one you say. The most interesting fact is that i installed the 4 axis to the 3 axis controller. May be it even outputs signals on axis, dont have the time to check but problem is it does not show 4rth axis on DRO screen, so even if it works is no good. So as i say, its not firmware. Otherwise software 4 axis works on 3 axis hardware without a problem.
my machine will use 2 cpu as controler by changing one of it plc one of it DDCSV my plc connected -puls but it is writing like down in manuel page 14 +5V-S Note (Common-negative wiring method) Not used drive.google.com/file/d/0B49xwe9ffk3fTUNDY0Q2UnFmTUE/view finaling i want to ask you have you trayed to -puls using ? not : my drivers are stepper and servo there are 2 of them
I bought one of these about two months ago and I am really liking it for its simplicity and price. It works great for me and I have really enjoyed learning how to use it more efficiently. Here is a video of my preliminary testing and how I setup doing tool changes using a M98 to call a program in the slib.nc file I added. ua-cam.com/video/Ln5wF09Z8UM/v-deo.html
Now the controller was upgraded to a new version. The new version supports NPN Switch and General MPG.
www.amazon.com/dp/B074FVNCTV
are you satisfied ? from whom you bought? as coping with liquidity traffic? if they upgrade
it reads and executes a 7 milion line G code without a problem. I pause the file and resume in middle of it after tool change because of broken tool. No problem. Just have to wait 15 minutes until it reads the 3 million lines again :-")
How is the software corrected for the perpendicularity of the axes?
No gantry squaring. Only mechanical.
Good morning, friend the 4 axis can be put as a slave of the Y axis ?.
On the Y axis I have 2 motors.
Or would it have to output an axis Y put 2 drivers one for each motor?
2 drivers connected to Y axis. No problem at all. I have servo motors that way on a very fast machine. Signal is strong.
Hello i have bought a 4 axis DDCSV. I use artcam or vectric aspire. What post processor can I use for the ddcsv controller. I want to use it with a manual tool change.
Thanks in advance. Mario
general G code
Thanks Boyan. What i can do to use a manual tool change?
hello Boyan, I’m interested with DDCSV, can you tell me how the precision of this, if I want to use to retrovit my manual milling machine,
It has never failed me in any way. The precision will depend on your setup but it has more than enough for a mill
Boyar, very nice and good demo. did you try to connect Laser device to this controller?
Sorry can’t understand English well cause I’m don’t speak it, in which part you explain how to configure it ??
Pues entonces tienes que bajar el manual en pdf y traducirlo pagina por pagina usando el traductor de Google. No veo otra manera de programarlo si no hablas Inglés
Boyan Silyavski it’s a very big one 😅, but I just want to know if you explain in the video the speed setting ? Thanks for answer so quick
Boyan Silyavski and for the engine ramps.....
Axis A, can be set up to Tangential cutter 360º.
- In Mach3, in configuration must be activated in
Rotational:
·Rot 360 rollover
·Ang Short Rot on G0
Can you do this on the DDCV1.1 console?
Setting of axis A (rotation) in Mach3
cdn.thingiverse.com/assets/a9/6a/03/49/a0/general.png
cdn.thingiverse.com/assets/8b/d1/75/35/bc/Settings_Alt-6.png
www.thingiverse.com/thing:1436870
Can the 4 axis one be used for lathe?
If you mean Lathe/MIll - No.
I mean just for a lathe.
No, it will not. You need dedicated lathe controller. its double the price
Thank you very much on clearing out that this is not suitable for lathe.
Hello dear
I have one controller dccvs2 4 axis .can I use only 3 axis with 3 drive in this controller?
Thanks for your help !
No problem. Only use 3 axis. Ignore 4rth
i want help in feed rate setting can you talk to me on khan.zuby94@gmail.com
Hi, I have the same controller but cannot open files, I can see the simulated toolpath but when i press start nothing happens, has something similar ever happened to you? everything else works fine
It have never happened to me. Find the files and update the controller , there is a forum about it with updated files.
Boyan Silyavski thank you, I already updated the firmware with no success, is there some pre-operation check that the controller does? Could be a problem that I'm working in negative coordinates space? With the zero in top right corner of the plane
I work with Z0 on top of Z axis, which is the normal thing according to me. So lowering the Z is with negative sign. I think You will have to download the manual and check it line by line/the controller settings/ as it have happened to me to accidentally change a setting and then had to do that. It took me an hour but i figured my mistake. You willneed to be patient not to miss something. But first of all check as there is a setting which says if the controller is comanded by G code, so there may be the mistake, you could have switched it to 100% mmanual mode
Boyan Silyavski thank you, I will check again also if I've already check all the settings, can you remember what setting was the problem for you?
Hello boyan,
Do you know try the option “ find center” i set it on key2 in the menu.
It is not working .... any idee..... thanks
can i configure this device to use an slave stepper? Thanks and regards from Chile!
No. But signal is strong and you can connect 2 drives to one axis output. No problem. Works perfectly. You will need a hard stop then on machine so you can bump manually the 2 axis there so they are square and then switch on machine. That simple.
+Boyan Silyavski, are you interested in an firmware upgrade to 2016-06-10-80?
I dont think you are actually upgrading the firmware. Its a software upgrade. I have that installed now. The one you say. The most interesting fact is that i installed the 4 axis to the 3 axis controller. May be it even outputs signals on axis, dont have the time to check but problem is it does not show 4rth axis on DRO screen, so even if it works is no good. So as i say, its not firmware. Otherwise software 4 axis works on 3 axis hardware without a problem.
my machine will use 2 cpu as controler by changing
one of it plc
one of it DDCSV
my plc connected -puls
but it is writing like down in manuel page 14
+5V-S
Note (Common-negative
wiring method) Not used
drive.google.com/file/d/0B49xwe9ffk3fTUNDY0Q2UnFmTUE/view
finaling i want to ask you have you trayed to -puls using ?
not : my drivers are stepper and servo there are 2 of them
Who produces it?
Unknown Chinese company.
looks like a very nice controller , thanx for the review !
Thank you so much for the review, +Boyan Silyavski
or you can specify where you purchased? Because there are many scammers alliexpress?
Buy from Rattm motor , its the same
I bought one of these about two months ago and I am really liking it for its simplicity and price. It works great for me and I have really enjoyed learning how to use it more efficiently. Here is a video of my preliminary testing and how I setup doing tool changes using a M98 to call a program in the slib.nc file I added.
ua-cam.com/video/Ln5wF09Z8UM/v-deo.html