How far does the wire need to be placed in the wire connector? Should it just be in the tunnel where its being crimped or does it need to be exposed on the flat part?
When done properly, The exposed wire should be just in the tunnel where you crimp. So another tip I forgot to mention is that if you look at how long the tunnel part is, that will give you an idea of how much insulation to trim off your wire so no wire is exposed. Hope this helps. Thanks for watching. Please like and subscribe
They are called self adjusting wire strippers. They can be purchased from amazon. They cost less than $20. Thanks for watching. Please like and subscribe
I've watched several videos where the wire that's being tapped into is not peeled back at all with the wire stripper. and the locking tap is placed directly on the coating of the wire. how would that even work if the metal of the locking tap isn't making contact with the wire/copper itself? am i missing something?
The manufacturer says to just push on and the tap is supposed to cut into the wire, however in my experience the blades in the tap are so dull that they only kink the insulation but don’t penetrate. Perhaps the other videos featured a different brand of tap that pierces the insulation better. But I think it’s best to pierce it first. Makes a better connection. Hope this helps. Thanks for watching. Please like and subscribe
Fully agree. If one chooses the correct size of the T Tap for the cable to be connected, peeling back the sleeving is really unnessary. Also, with the peeling, it exposes more of the copper and this is more susceptible to shorting.
I want to connect my LED DRL lights with T-taps. My problem is, the wires from the LEDs are really tiny, and I can't crimp them into the connector. Please do you have any advice for this?
@@BillOfAllTrades2016 Im taping into my parking lights wire, which is successful. But Im not able to crimp my wire from LED strips, bcs they are smaller and they dont hold in the connector.
No definitely not. You will need to go to a hardware store and ask them for the correct connectors for home electrical. These are only for low voltage accessories.
Why would it not be safe? I wouldn’t demonstrate a method if it wasn’t safe. The application will define the outcome of how long it lasts. Things like outdoor may be shorter life then indoor. Wet vs dry environment. At work we have these on a forklift for ten plus years.
Yes here it is. T-Tap Wire Connectors, 22-18 AWG... www.amazon.ca/dp/B09N92FJ8J?ref=ppx_pop_mob_ap_share Thanks for watching. Please like and subscribe
How far does the wire need to be placed in the wire connector? Should it just be in the tunnel where its being crimped or does it need to be exposed on the flat part?
When done properly, The exposed wire should be just in the tunnel where you crimp. So another tip I forgot to mention is that if you look at how long the tunnel part is, that will give you an idea of how much insulation to trim off your wire so no wire is exposed. Hope this helps. Thanks for watching. Please like and subscribe
I’m assuming u can use this on a positive and negative wire for let’s say a speaker wires ur trying to connect?
Yes that’s correct. It will work on both positive, negative, and ground wires. Thanks for watching. Please like and subscribe
Are you doing all 3 separately?
What is the name and where did you get the wire stripping tool?
They are called self adjusting wire strippers. They can be purchased from amazon. They cost less than $20. Thanks for watching. Please like and subscribe
I've watched several videos where the wire that's being tapped into is not peeled back at all with the wire stripper. and the locking tap is placed directly on the coating of the wire. how would that even work if the metal of the locking tap isn't making contact with the wire/copper itself? am i missing something?
The manufacturer says to just push on and the tap is supposed to cut into the wire, however in my experience the blades in the tap are so dull that they only kink the insulation but don’t penetrate. Perhaps the other videos featured a different brand of tap that pierces the insulation better. But I think it’s best to pierce it first. Makes a better connection. Hope this helps. Thanks for watching. Please like and subscribe
Fully agree. If one chooses the correct size of the T Tap for the cable to be connected, peeling back the sleeving is really unnessary. Also, with the peeling, it exposes more of the copper and this is more susceptible to shorting.
I think this is why my back up cam didn’t work
I want to connect my LED DRL lights with T-taps. My problem is, the wires from the LEDs are really tiny, and I can't crimp them into the connector. Please do you have any advice for this?
What gauge wire are you trying to tap into? And what guage is the connector?
@@BillOfAllTrades2016 Im taping into my parking lights wire, which is successful. But Im not able to crimp my wire from LED strips, bcs they are smaller and they dont hold in the connector.
@@gwyneth6045 you need a smaller guage ttap
thank u!
You're welcome! Thanks for watching. Please like and subscribe
Hi, can this type of connector use for home wiring electrical 220v ie?
No definitely not. You will need to go to a hardware store and ask them for the correct connectors for home electrical. These are only for low voltage accessories.
@@BillOfAllTrades2016 thanks for the info.
The low voltage acc ie : car, audio, correct?
Yes that’s correct
Nice.
Thanks for watching. Please like and subscribe
I mean is this safe and how long does a connection like this last ?
Why would it not be safe? I wouldn’t demonstrate a method if it wasn’t safe. The application will define the outcome of how long it lasts. Things like outdoor may be shorter life then indoor. Wet vs dry environment. At work we have these on a forklift for ten plus years.
Do you have the link for these?
Yes here it is.
T-Tap Wire Connectors, 22-18 AWG... www.amazon.ca/dp/B09N92FJ8J?ref=ppx_pop_mob_ap_share
Thanks for watching. Please like and subscribe