Common Reasons a HOT TUB Will Not Heat [ TIPS and TRICKS ]

Поділитися
Вставка
  • Опубліковано 19 січ 2025

КОМЕНТАРІ • 37

  • @VIPPoolsandSpas
    @VIPPoolsandSpas  4 роки тому +4

    Make sure to check out our other videos.

  • @JonRitchie-mi7zn
    @JonRitchie-mi7zn 8 місяців тому +1

    Hey! Your videos are FANTASTIC! I recently followed your steps because my hot tub kept tripping the breaker. I unhooked the element, voila, it stayed on so I changed the element. I set my temperature like normal. However, now it’s heating EXTREMELY slowly. I’m talking 12 degree increase in about 48 hours. What steps would you recommend to diagnose that?

    • @VIPPoolsandSpas
      @VIPPoolsandSpas  8 місяців тому +2

      Change the sensors. Temp sensor is covered in calcium or about to go. Thats if the right element was installed. EG. 4kw or 5.5kw. Also. Whats the volts coming into the hot tub?

    • @JonRitchie-mi7zn
      @JonRitchie-mi7zn 8 місяців тому +1

      @@VIPPoolsandSpas thank you so much! We do have extremely hard water and that makes perfect sense!

    • @JonRitchie-mi7zn
      @JonRitchie-mi7zn 8 місяців тому +1

      @@VIPPoolsandSpas apologies, i didn’t see the rest of your comment. It’s 240V. And it’s the same element type that came from the factory, so it should be correct

    • @VIPPoolsandSpas
      @VIPPoolsandSpas  8 місяців тому +1

      Take the sensor out and put in some cleaning vinegar.

    • @JonRitchie-mi7zn
      @JonRitchie-mi7zn 8 місяців тому +1

      @@VIPPoolsandSpas update: got the sensors cleaned off and reinstalled! I have the tub running, it started at 75 degrees and hasn’t increased any in an hour. When I turned on the power, the heating light was blinking and then it turned solid. When that happened, I did hear something in the power pack click. The hot tub continues running normally from all I can tell. Any suggestions for anything else that might be going on?

  • @kakaws77
    @kakaws77 Рік тому +1

    Hi, I have a question. My tub recently stop heating. Everything look normal. No code and motor working fine on both speed it just not heating. I checked the filter and nothing else is broken. Where do I need to look?

  • @1Patient
    @1Patient 3 роки тому +2

    Excellent video. Great info.
    Would like to understand more control board issues, trouble shooting and repair, solenoid testing and replacement along with temperature sensors and relationships to control boards and possible error codes being displayed on different types of control board displays.
    Thanks brother, keep up the good work.
    🙂😎

    • @VIPPoolsandSpas
      @VIPPoolsandSpas  3 роки тому +1

      A lot of times I know it's the board but can't pin point it where. Normally I get a computer repair guy to fix some of my stuff or test it. I should get a electronics guy to test things and record it. I don't have the skills to tackle the electronics repair.

  • @MegaMrWillie
    @MegaMrWillie 9 місяців тому +1

    For some reason i get no red light on the dash light its not calling for heat and its only gettin 120v to the heating element ive tested everything besides the board ?? Think thats my issue no codes

    • @VIPPoolsandSpas
      @VIPPoolsandSpas  9 місяців тому

      120v at the element sure sounds like a heater relay.

  • @cheromilli2681
    @cheromilli2681 3 роки тому +1

    plug and play dream maker spa
    heating up verrry slow 2 days and only at 80* filter flap door at the top of the skimmer should I blast the hose down the skimmer to clean it? .filter is fairly new. thx

    • @VIPPoolsandSpas
      @VIPPoolsandSpas  3 роки тому +1

      do you have well water?

    • @cheromilli2681
      @cheromilli2681 3 роки тому +1

      @@VIPPoolsandSpas
      no, city
      I hear it turn off when I reduce the temp. I have at st .. not sure if it's stuck on ec cause when I check it starts at ec
      I've blasted the hose in each jet to eliminate air pockets... 🤔

    • @VIPPoolsandSpas
      @VIPPoolsandSpas  3 роки тому +1

      @@cheromilli2681 normally if its on economy, the temp gets around 80-85. Could be on that. do you know how to change it? What spa pack (what everything plugs into) do you have? Balboa?

    • @cheromilli2681
      @cheromilli2681 3 роки тому +1

      @@VIPPoolsandSpas dreammaker ezspa
      not sure why it stays on ec when I change it
      🔺️ st

    • @VIPPoolsandSpas
      @VIPPoolsandSpas  3 роки тому +1

      @@cheromilli2681 remove the door of the spa pack and there should be red and white dip switches. I think its #7 you can change it to just standard mode. SEE BACK OF DOOR FOR DETAILS.

  • @jslade60
    @jslade60 2 роки тому +1

    On my Hot springs hot tub the code for the pressure switch came up. It stopped heating. I jumped the pressure switch the red light on the board came on but the hot tub still doesn't heat. What do I try next?

    • @VIPPoolsandSpas
      @VIPPoolsandSpas  2 роки тому +1

      is the circ. pump running? whats the problem? Is there an error code?

  • @chelmjustice1226
    @chelmjustice1226 Рік тому +1

    My hot tub isn't heating. On the display board if I hit the cool button to turn it down it automatically goes back up. And stays at 104. So it shouldn't do this?

    • @VIPPoolsandSpas
      @VIPPoolsandSpas  Рік тому +2

      It's the topside. Need a new one. Fix that first. Could be another issue besides that.

    • @chelmjustice1226
      @chelmjustice1226 Рік тому +1

      @@VIPPoolsandSpas I wanted to thank you. That fixed it. The tub has been sitting for a couple years and everything else works fortunately.

    • @VIPPoolsandSpas
      @VIPPoolsandSpas  Рік тому +1

      @@chelmjustice1226 glad it worked out.

  • @roberthamilton2355
    @roberthamilton2355 8 місяців тому +1

    The hot tub was heating fine before I drained all the water out to clean the hot tub after I fill the back up. All the pumps are working but not heating up now!

    • @VIPPoolsandSpas
      @VIPPoolsandSpas  8 місяців тому +1

      This is very common. Test your heater element. AND. Make sure you don't have an air lock.

  • @travishopper5133
    @travishopper5133 Рік тому +1

    Do some tubs not have a pressure switch?

  • @coreyk5536
    @coreyk5536 2 роки тому +1

    Chasing my tail with my tub. I can turn the tub off at the breaker, turn it back on and it will heat up to a chosen temp of say 98. after this initial heat-up it will not heat again, until I shut the power off at the breaker and start the process again. The fact that it will heat leads me to believe the element is fine, but maybe a relay is bad or something else on the board not communicating to heat again..

    • @VIPPoolsandSpas
      @VIPPoolsandSpas  2 роки тому +1

      Could be a sensor issue. Your heat sensor maybe.

    • @walterstrikes
      @walterstrikes 2 роки тому

      i have the same issue. Any solution yet?

    • @coreyk5536
      @coreyk5536 2 роки тому +1

      @@walterstrikes it was a relay on my circuit board that would not close the loop to allow the heater to produce 240v. Unfortunately my boards are obsolete so I retrofitted the board and heater with a Balboa BP7 bundle.

  • @davidbrooke4829
    @davidbrooke4829 2 роки тому +1

    i replaced heat element, checked for air locks, i have voltage at the element. and if you shut valves on the union to heater, it gets hot.
    At the filters their is no sucking . pressing jets 3 on immediately cuts the heating symbol off.
    no error codes. any advice greatly appreciated