Thanks so very much for your instructions that were so easy to follow. Mission accomplished and I now have a wonderful wheelbarrow again. Kind regards and best wishes from England. 😊
Getting the second bead over the rim once the new tube is installed is not in any way easy. (as shown) Especially if you are replacing the tire with a new one. I have changed hundreds of bicycle tires and tubes successfully. After spending 3 hours, two neighbors and one wife later I brought it to a lawnmower repair shop. Screwdrivers, tire spoons, lubricants are of little help. This is a job you pay someone else to do.
Thank you, this is my first barrow tyre and tube change. I’ve got to this stage and been feeling really silly and stuck at this point. Your comment is really comforting! 😂 I’m determined to do it though 😅
Haha@@mangoshake9435 I'd forgotten all about this! Thanks to this video I got the old tyre and tube off, and the new one half on, but no!!! Unfortunately, no matter how hard or how long I tried, with levers etc etc, it defeated me. In the end, I had to ask my brother to do it (trained mechanic). He did it with his bare hands, lots of patience, just gently and firmly squeezing the edge over the rim. It took a few tries even for him, but he did say it was harder with a new tyre as well as new tube!
I had a tail wheel dolly tire that needed a 3.0 - 4 inner tube (somewhat smaller than you wheelbarrow tire. Anyway the video gave me the confidence to change the tube properly. As mentioned the main risk is damaging the tube with the screw driver. I'll fill it with Nitrogen which has larger molecules and does not go down as easily.
Why did he take the tire completely off the rim only to put it right back on. Don’t get it. I never do that when doing this. Unnecessary, unless I am missing something.
It's much easier to take the old tube out when it is completely off. And it is easy to put the first side back on. In part it depends on the size of the tire.
Christ you made putting that on look so easy. Took me 15 minutes and some swearing but I got it. Thanks.
Glad I could help
Brilliant. Saved me hours of messing about. Cheers.
You're welcome!
Thanks so very much for your instructions that were so easy to follow. Mission accomplished and I now have a wonderful wheelbarrow again. Kind regards and best wishes from England. 😊
Thanks, glad it helped!
You have the most calming and reassuring voice. You should do voiceovers mate! David Attenborough's getting on...
Thanks! And good idea...
I second that motion ❤
I third this! You sound so calm and reassuring; you make me believe I can do this even while struggling! 😊
Excellent voice for ASMR.
Lam.Tot Well.Done
Cảm ơn Thank you
Thank you for posting-just what I needed!
Glad it was helpful!
good and clear instructions, thank you.
You're welcome!
Getting the second bead over the rim once the new tube is installed is not in any way easy. (as shown) Especially if you are replacing the tire with a new one. I have changed hundreds of bicycle tires and tubes successfully. After spending 3 hours, two neighbors and one wife later I brought it to a lawnmower repair shop. Screwdrivers, tire spoons, lubricants are of little help. This is a job you pay someone else to do.
Thank you, this is my first barrow tyre and tube change. I’ve got to this stage and been feeling really silly and stuck at this point. Your comment is really comforting! 😂 I’m determined to do it though 😅
@@MrsTigerbalmdid you do it?
Haha@@mangoshake9435 I'd forgotten all about this! Thanks to this video I got the old tyre and tube off, and the new one half on, but no!!! Unfortunately, no matter how hard or how long I tried, with levers etc etc, it defeated me. In the end, I had to ask my brother to do it (trained mechanic). He did it with his bare hands, lots of patience, just gently and firmly squeezing the edge over the rim. It took a few tries even for him, but he did say it was harder with a new tyre as well as new tube!
I had a tail wheel dolly tire that needed a 3.0 - 4 inner tube (somewhat smaller than you wheelbarrow tire. Anyway the video gave me the confidence to change the tube properly. As mentioned the main risk is damaging the tube with the screw driver. I'll fill it with Nitrogen which has larger molecules and does not go down as easily.
Just followed this, it worked but I swore 18 times and nearly threw a screwdriver at the wall
Yes, you need the patience of a monk for this task!!
30 psi that's what I was looking for!
Excellent, I'm glad my video helped!
Can't imagine a job that I hate more!
Why did he take the tire completely off the rim only to put it right back on. Don’t get it. I never do that when doing this. Unnecessary, unless I am missing something.
It's much easier to take the old tube out when it is completely off. And it is easy to put the first side back on. In part it depends on the size of the tire.
I don’t do that part, I puncture the old tube and make it super flat and pull it out, much easier
No. Didn't work. But cheers.
Lam.Tot
Lam.Tot