Car Audio Installation in Volkswagen VW Beetle - Kicker Subs & Amp + JVC Stereo
Вставка
- Опубліковано 27 сер 2024
- Car subwoofer, amplifier, and stereo installation in a Volkswagen Bug. Watch as Sonic installs two Kicker COMP subwoofers, a Kicker 2010 ZX300.1, and a JVC KDR-610 car stereo. In this video we show how to remove the factory radio and install the JVC head unit. We also installed two 4-ohm Kicker comp subwoofers and wired them to a final impedance of 2 ohms.
Main page:
www.sonicelectr...
Knowledge Base:
knowledge.sonic...
Sonic Blog:
blog.sonicelect...
Sonic Forums:
forums.sonicele...
This is one of the better how to videos I've seen, well done
Dude you really made it simple. You really are a professional. The setup was so clean!
That's a very good question. There is a dash kit available and it is the Metra 99-9008, which is available on our site. It might of not been available at the time of this install.
where do you get the battery cable thru the fire wall?
@vespaT27 That particular vehicle doesn't require a dash kit. The the factory radio is a standard single din size, so when you install an aftermarket radio you'll just use the volkswagen removal keys to remove the factory radio and use a mounting cage that's supplied with aftermarket radios to mount the radio into the factory area. No dash kit is required for your vehicle.
@DerbiSmdu1480 The remote wire will go from the radio to the remote input on the amplifier. This wire allows the amplifier to be turned on when your vehicle does.
@javiderek31 No this is not normal, the problem here is that the remote wire from the amp is more than likely connect to an accessory power wire. So the amp turns on and off with the car and not the radio. To fix this problem make sure that your remote turn-on wire is connected directly to the remote output of the radio, this will cause the amplifier to turn on and off along with the radio.
The Hifonics Brutus amplifiers are great because they are both affordable and efficient. We recommend these amps for people who are looking for a lot of power and who have the electrical system to support it. If they say they put out 2000 watts, they will put out very close, if not 2000 watts. If you check out our reviews on each of them you will see how much people love them. Hope this helps!
What's the box size
Hifonics is a reliable brand and have very decent amplifiers. They are most definetly not a cheapo brand.
That is just the MAX rating of the speakers. It is what they can handle. You don't want to run them at that output because you can blow them. You want to match the RMS rating of both the amp and speakers. That is your best solution.
Well done Brendan!! It is now obvious how you got to be on the Sonic Electronix UA-cam vids. Your expertise really shines in this type of video. Great job at clearly & quickly explaining the steps in an organized manner. This is probably my favorite Sonic Electronix vid!! (Don't tell Seth) :)
@SoToxsiK That's fine, you're not significantly under powering them at all. You can throw some extra power to those comps though, they can handle an extra 100 watts each if you really want.
@SoToxsiK It looks like for the most part we used the AK04 for power/ground and RCA connections. The speaker wire used is Kicker speaker wire. I believe we used the 09XW1220 for speaker wire. It's 12 gauge Kicker speaker wire to get some better signal from the amp.
@Amalemodel Its the blue and white wire on the harness that came with the radio and the solid blue wire coming from the car harness. Make sure you don't confuse the remote turn on wire with the power antenna wire.
Soldering is always the most secure way to make a connection. However, crimp connectors are good as well. Just make sure you properly crimp both sides of the crimp connectors and you will be fine.
try it your self man its really fun i have done it and i cant get enough of it now
@joshdesjardins6 A single channel amplifier would be the same thing as a Monoblock amplifier. Usually, most monoblock amplifiers are made with Class D Circuitry, so in this particular case this amplifier is a Class D Monoblock Amplifier, which you can also call a single channel amplifier if you want to.
@SoToxsiK Break-in time usually takes about 24 hours of playing time for your subwoofer. During this break-in period keep your amplifiers settings around half-way of where you want them at the end of the break-in period. For example, instead of turning your gain settings on the amplifier to half way, turn it to about half of that. This will help keep your subwoofer distortion free, or keep them from heating up too much as well. Good luck with that setup!
The enclosure is what will make a subwoofer sound it's best. You have to double RMS power just to get a little more volume out of your subs. The enclosure is important. Subwoofers can handle a wide range of RMS power, staying at the recommended is not required. Also, customer budget is a big factor in all of this. Usually, over powering by a little bit is a good idea.
@bsiffy When using a crimp cap or butt connector all you need to do is connect the copper from the wire to the metal inside of the connector. This will conduct the other end of copper. The ends of copper don't necessarily need to be inserted until they touch each other, although you will want to insert them as securely as possible so the install will last.
If anyone's wondering what the last song is, it is Pursuit of hapiness by Kid Cudi BUT.... its dubstep...... for those on Lime or Frostwire: Pursuit of Happiness (Steve Aoki Mix - The Killabits Dubstep Re-work).
@JERMX101 The best way to do this is using L-brackets, this will allow you to mount the enclosure to the floor. You might want to use one for every corner just to make sure its securely mounted.
@EASYxxZ It's always good to have an aftermarket stereo since it makes hooking up the amplifier easier. If you don't want to get a stereo you could always get a Line Output Converter to convert your speaker wire into RCA outputs to run to your amplifier.
@MilRom9 You can also pickup the hardware from us as well. The Scosche TK12V is a great entry-level kit with wire crimpers, some butt-connectors, a multi-meter, and a pry-tool. Just search for TK12 or TK12V on the green search bar on our main website and you will be able to find these tools. If you need just connectors, we sell them in packs of 100, so we have plenty of different ways to stock up your connectors.
Yes the power wire was ran through the firewall on the drivers side. There was an existing wire grommet that it was run through.
@eagle0924 You might want to consider the box you are using. If it is a ported or vented box, it would be a good idea to switch it out for a sealed box. This will cause your bass output to be more accurate and precise. Make sure that the internal volume is between .5 and 1.0 cubic feet.
You would have to call a local installer to get price quotes for installation. As far as the system goes, you can call our customer service line a call and they can help you pick out a system.
Why didn't you show the stereo after the install ??? even with no front trim piece it would have been nice to see it !!!
We will definitely try to get a video of that install.
@hendlank A perfect amplifier would be the Alpine MRP-M2000. You must make sure that it is connect in a Series configutation for a final impedence of 4 ohms and 1500 Watts.
@jacedison In general, it's perfectly fine for a car audio system to be run from 4 ohms to 2 ohms, as long as you hook them up correctly. With your particular setup, you may be under-powering the subwoofers, even at 2 ohms. Check to see how much RMS power your subwoofers require (not peak or max) and see how close that matches up to your amplifiers power output at 2 ohms.
If your subwoofers are dual voice coils (two +/- terminals) you can only wire to 1 or 4 ohms on your amplifier.
Good, Clean Install, Good Job
hello i had a question. I have 2 kicker comps 15" 4 ohm and want to wire them to 2 ohm. Can i hook both to a mono block amp?
@jacedison We would recommend only using this boss amplifier for one of these subwoofers not for two. You are going to need a more powerful amp to run two of them.
Nice work ! Keep it up, Man!
@ChevyGangman323 You will need to use the remote wire coming from your head-unit, and rout it to both of your amplifiers as well as your Epicenter's remote input terminals. The remote wire will trigger all of your devices to turn on whenever your head-unit is powered up.
@TheToTooTwo Not in this particular installation. A Big 3 Upgrade works wonders for system that require a little more power. This system only uses a total of 300W RMS. Although a Big 3 Upgrade will always help, you don't really need to do one until you're getting towards 900-1000W RMS or more. Than you'll definitely want to do a Big 3 Upgrade.
You always disconnect the battery when changing anything in the vehicle. We are not aware of any issue with the bug where you need alternate power sources.
Two 12's would be just fine for your car. The 15's are also good for a budget system, but are a little over-kill for your vehicle.
It does as long as it has RCA outputs to run to the amp.
Vic, you don't want to do that. You need to make sure you use a terminal for it so your connection is secure. The way your friend did it could cause problems if it comes lose or if anything hits it. It is dangerous.
You're going to need a dashboard installation kit to put an aftermarket receiver in your vehicle. Metra recommends the Metra 99-9011, which we have available on our website. Give us a call if you have any other compatibility questions and we would be happy to help you out!
@fastodie Pursuit of happiness.
@EricsFarm Yes you will be able to hook up these subs to a monoblock amp. You will need to wire them in a Series configuration. You can find a visual diagram through the following link:
knowledge.sonicelectronix[DOT]com/tools/subwoofer-wiring/
For a car like the Century, you should be fine with two 12" woofers. Thats what i would recommend.
@ThaDmo541 LOL. Don't worry. We aren't entering in our own contest. This is just for you to enjoy!
@TNSxDYNASTYx The Zx300.1 will be the perfect amplifier to run with these subs.
nicely done
Two Single 4 Ohm CVR woofers can wire down to 2 ohms.
@SonicElectronixTV you thanks for the ifo man
@vespaT27 You'll need to purchase separate wiring for the MTX Magnum package. For the radio removal, you'll also need to purchase VW Radio Removal Keys separately. You will need an antenna adapter for that vehicle if you would like to retain your AM/FM transmissions. The Metra 40-VW10 is a great option to use in this particular case. The model number for the radio removal keys is the Metra 86-9001.
@hendlank Are your Type R's Dual 4 ohm or Dual 2 Ohm?
If you don't feel comfortable doing the installation yourself and learning some about car audio installations, then take it to a professional and get pro results.
However, if you want to do it yourself, then check out our Knowledge Base and other videos for some help.
@Djordjeeee451 It is possible. Depending on the stereo you choose. Some car stereos might have a lower signal-to-noise ratio, or a less than quality digital-to-analog converter. These are huge when it comes to sound quality. Check out some stereos by Kenwood, Pioneer, JVC's new stereos, and you'll fine happy with the sound quality you get.
I went to install a aftermarket radio in my 1995 Toyota Tacoma, and it was the fourth add-on...
Installing after market stereos in a beetle may render the code scanner inoperable. A loop back cable has to be clipped or youll have issues
Can u send me a link on where to get the harness for a vw 2004 beetle? Im having trouble finding the right one
Search ebay
for all of those speakers and everything how much would it cost all together?
If I were you, I would have hooked up the ground to the seatbelt bracket. It is the best solid ground you will find, and it's in the trunk, and don't have to put holes in your car.
Wow really!? Thanks so much..okay i have one last question..how long does it usually take to break them in?..I've only had them for about a week..
lmao those kickers motors and baskets look alot like my boss audio subwoofers
Do you have to remove the stock stereo for any system
If you want to install this to your stock stereo, then you would need a line out converter.
@SonicElectronixTV yo thanks for the info man
@bassline123456789 You can drop the impedance of any speaker. So if you have two single 4 ohm Kicker Comps and you want to wire them down to 2 ohms like in the video, go ahead! That will work great!
hey can u make a video showing how to replace the front+back speakers please?
@importracer46 We would recommend just going with the zx300.1 to run these two subwoofers.
so I can't remove the stock stereo and hook the with the system up with it then put the stock stereo back
@awille13 Yes, the zx300.1 is a perfect match!
Just please tell me what box size is that
Song at the end: Kid Cudi- Pursuit of Happiness.
This was great!
I own this exact car, And I am installing my amp and sub soon, I was wondering where you ran your RCA and Battery ground to the trunk, you seem to have skipped that step in the video. I would really appreciate your response, Thanks for your time!
Did you ever find out how to run the wires?
Cool. Thanks homie
when crimping the factory wire harness to the aftermarket wire harness do the actual copper wire parts have to touch each other? and if they do should you twist them together then put the crimp part over them?
ahh I did recognise the Song in the beginning ;) Kid Kudi ftw :D
Any ideas on why the radio would stop working if the car hood was closed?
So I was on the website and saw a lot of wiring kits that look similar to the one that was used in the video..I just wanted to know exactly what kind of wiring kit was used??..from what brand??..
Can you please give me a more detailed explanation of how you wired the subs to the amp? Thanks alot!
Then you need to buy an amplifier with a Hi-Level input as well as an amp wiring kit, a subwoofer, and an enclosure.
is it bad if u dont have a terminal for ur power wire to ur battery because my friends wants to know cuz all he did was he stripped the wire and wrapped the copper around the positive terminal on the battery
Thanks so much!! You guys rock!! :)
What do you think is better, soldering connections or use the crimp connectors?
So quick question. So its safe to drill a small hole in a subwoofer box to run the wire through?
Need some serious help, I have a 2011 Volkswagen Jetta SE I want to remove the old factory radio and replace it with a double din JVC or Pioneer havent decided yet the problem I'm having is the din for the radio is rounded instead of a sqaure and I dont see how I'm going to manage to put a square insided of a rounded square ...
i got a question. i got a car from a friend it came with a rockford fosgate amplifier and a alpine type r 10" sub. the problem im having is that i listen to broad spectrum of electronic music and it all sounds good except for hardstyle. if your familiar you know hardstyle has a very fast beat, my sub can't keep up with it and it is often a beat behind and just screws up the song. i was wondering if there was anything i could do to fix this.
Can u guys post more install videos that u guys do for other cars
great video! i am looking to buy 2 12 inch kicker comps, and the rms is 150, so the amp in this video would be perfect?
I have never installed subs in my life and I just got a 4k watt amp and want to get two 12's as well should I get professionally done or should I try and do it myself?
Chevygangman323 my brother in law sais just wrap the remote wires on a fuse that turns on when the car does! I did that and it worked!
@360ModsandHacks thanks
Where would I find a spot to put my power wire through the firewall on my 2002 new nettle 1.9 tdi
Great video! Nice products, too :)
I have two kicker comps 12" and I'm only putting about 100 rms to each speaker..is it bad or harmful to the subs to under power them?..
im having trouble with it, because the colors of the wires in the car are different. can you help me
@jacedison The peak power is a completely useless number. You want to only pay attention to the RMS ratings. However, being that this is a boss amplifier, even their RMS power ratings are going to be exaggerated because this is not a CEA compliant amplifier. This amplifier will probably not be powerful enough.
@fastodie It is NOT Pursuit of Happiness! I don't know what it is, but I know it's by Kid Cudi
Do you have to put in the jvc radio or can you keep the monsoon in?
@SonicElectronixTV alright thanks!
Hi. I would like to know what would be the best kicker amplifier to buy to run two 10" Kicker comps?