Explaining phase monitor|phase failure relay|ELECTRECA

Поділитися
Вставка
  • Опубліковано 24 лис 2024

КОМЕНТАРІ • 96

  • @nyansungatembo2883
    @nyansungatembo2883 2 роки тому +3

    I want to thank you sir the education given so far so good I have learned a lot just asking you sir to continue we really appreciate and enjoy the way you explain it's really nice and clear thank you very much

  • @rosekamotho3081
    @rosekamotho3081 2 роки тому +2

    Very educative videos electreca,I have learnt almost all controls from your videos,I would just like to learn more on how to do the pump panel on auto and hand.

    • @electreca1
      @electreca1  2 роки тому

      I will do more video on that, Thanks for watching.

  • @kibacademy9619
    @kibacademy9619 4 роки тому +2

    Congratulation brother...ur channel is very educative I did electrical but we didn't do much of this practicals....👍👍👍👍

    • @electreca1
      @electreca1  4 роки тому +1

      Thank you........and well come. fill free to ask quetion here, i will always do my best to answer.

  • @maths-media9218
    @maths-media9218 3 місяці тому +1

    hi sir how you doing.your explanation is so nice.please can u make video on electrical connection of phase failure for pump

    • @heinhaas7099
      @heinhaas7099 Місяць тому

      How to wire a overvoltage|undervoltage protection system?

  • @hajimuhammad2928
    @hajimuhammad2928 2 роки тому

    An Excellent Video Presentation for learning with high flying colours.

  • @samuelagbai7392
    @samuelagbai7392 7 місяців тому

    Good day engineer. Nice job. Pls I want to ask, is there a way we can use a single phase on this device?

  • @mugishayves9033
    @mugishayves9033 2 роки тому +1

    Thank you very much! Explanation are very clear and helpful 👌

  • @erickademe
    @erickademe 2 роки тому

    Big up on yah self much love from Uganda.

  • @nsimbehamuzah7689
    @nsimbehamuzah7689 Рік тому

    Thanks a lot I have learnt much through your channel

  • @mesumbeamstrong3122
    @mesumbeamstrong3122 2 роки тому +1

    Engineer,is there a connection to bypass the phase failure,expecially when you are not in the disposition have another at that moment,and you want it to continue work before you go and look for another

  • @chidiemelobe1044
    @chidiemelobe1044 2 роки тому +4

    Nice video, but could you please teach with diagrams as well. Thanks

  • @lawrenceatkinson
    @lawrenceatkinson Рік тому

    You didn't put it out there the way I would have wanted but I'd learn something about the device from you

  • @leonardchinonso7067
    @leonardchinonso7067 2 роки тому +1

    I appreciate your efforts

  • @adtech515
    @adtech515 3 роки тому

    i am from Ethiopia please keep going bro

  • @kayiwareagan9385
    @kayiwareagan9385 2 роки тому

    This guy has taught me automation at best, that i come here watch a video, go do the circuit amd get paid.
    My question is on this video.
    In the components the last component on your right, what exactly is that.

    • @electreca1
      @electreca1  2 роки тому

      That's a borehole control panel, the device on the right is called floatless level switch. It's a protective device it switches off the pump incase water level goes below threshold.

  • @gabrielchikwasha1970
    @gabrielchikwasha1970 7 місяців тому

    Can I connect phase failure and breakers only exclude the other?

  • @dennisimujaro512
    @dennisimujaro512 Рік тому

    Can I use one timer in a GEN and Raw power change over?

  • @cynthiamthabiseng6282
    @cynthiamthabiseng6282 7 місяців тому

    Can you please demonstrate DUR electronic timer, time range A and time range B

  • @hajimuhammad2928
    @hajimuhammad2928 2 роки тому

    Thank You Very Much, Sir.
    5 Stars = 🌟🌟🌟🌟🌟
    👍

  • @mwanawahakaemmanuel7232
    @mwanawahakaemmanuel7232 2 роки тому +1

    Circuit diagram please of how it can be connected thanks

  • @denofilms2438
    @denofilms2438 Рік тому

    Good job engineer

  • @chrismasika9786
    @chrismasika9786 3 роки тому

    What of missing phase after the contactor i.e on the load side of a contactor assuming there was a fault with the contactor or overload relay for that matter will the phase failure still be of help?

  • @leonardchinonso7067
    @leonardchinonso7067 2 роки тому

    I want you to do a video on water treatment plant panel connection pls.

  • @leonardochieng7220
    @leonardochieng7220 7 місяців тому

    Hello can you pls explain how RM35TF30 voltage regulator work

  • @kayongonaziiru9025
    @kayongonaziiru9025 3 роки тому

    Its quite interesting we watch u always

  • @demukaconceptelectric
    @demukaconceptelectric 3 роки тому

    Good explanation.But I have a question? Does it mean that the phase failure relay is the one which is supposed to supply power to the coil of the contractor...

    • @electreca1
      @electreca1  3 роки тому

      No... The phase failure should supply the circuit. let me explain in an example, you have a 3phase pump to run using a self-holding circuit. From control Breaker through phase failure(NO) through overload relay(NC(9798),) From here you can supply the circuit.
      Op it helps

  • @wasswafredricklutaaya521
    @wasswafredricklutaaya521 11 місяців тому

    Thank you very much for the information relayed 🙏🙏🙏

  • @reyelectrical
    @reyelectrical 2 роки тому

    Now i understand thanks for this video man

  • @sekyanzinathan7521
    @sekyanzinathan7521 3 роки тому

    Thanks u sir. Do u just need to keep on changing two phase of incoming power until you get right direction (when rectifying a change in phase at transformer)

    • @electreca1
      @electreca1  3 роки тому +1

      You only interchange 2 phase once.

    • @Kenyan_Electrician.
      @Kenyan_Electrician. 2 роки тому

      Hey & should you interchange at the main breaker or at overload... please ?

  • @Aleeyuahmad-qr8uz
    @Aleeyuahmad-qr8uz Рік тому

    How can I sizing the contactor for each hp motor from 10hp to 50

  • @VINCENTMELLY-g9i
    @VINCENTMELLY-g9i 10 місяців тому

    What causes contacter to vibrate and spark after motor rewinding

  • @emukulemartin6828
    @emukulemartin6828 Рік тому

    Blessings, so elaborate.

  • @ABIREEBEJAMES-ig7rm
    @ABIREEBEJAMES-ig7rm Рік тому

    How to calculate voltage because some phase monitor start from 55 to 95 on under voltage

  • @mareysaad6597
    @mareysaad6597 Рік тому

    It is informative, however you can still provide better than this
    ❤️❤️

  • @gvncj
    @gvncj 4 роки тому

    Can you please show us how you wired this in or just post up a little wiring diagram:)

  • @nel600
    @nel600 Рік тому

    Great video

  • @moriamartinmariomuriira2644
    @moriamartinmariomuriira2644 2 роки тому

    Hi, is it a must that the 3 phases entering the phase failure must go through a MCB each?

    • @electreca1
      @electreca1  2 роки тому +1

      Yes, to to protect the phase failure.

  • @felixnartey3759
    @felixnartey3759 2 роки тому

    Should I please connect the phase failure before the contactor

    • @electreca1
      @electreca1  2 роки тому

      Yes, The phase failure gets the current first before the contactor coil.

  • @kariukikariri5759
    @kariukikariri5759 2 роки тому

    Hi you didn't explain on how to configure the timer over and under voltage plz

  • @saibalbose5796
    @saibalbose5796 2 роки тому

    Please post a video of a full commissioning of a phase failure relay which triggers an ATS Controller and gives signal to the Generator ro start

  • @antenehberhanu4467
    @antenehberhanu4467 Рік тому

    Hello bro how to set the phase failer relay?

  • @rajieid
    @rajieid 4 роки тому +1

    Thank you very good explanation

    • @electreca1
      @electreca1  4 роки тому

      Your well come and thanks for watching

  • @comedystorekissey2850
    @comedystorekissey2850 3 роки тому +1

    Thanks brother but it's should be better if u use appropriate phase colours for easy understanding and even the beginners to avoid making mistakes.

  • @smalls2845
    @smalls2845 2 роки тому

    my question is, how do you select or calculate the rating of the phase monitor required for you circuit?

    • @electreca1
      @electreca1  2 роки тому

      Normally the control circuit will draw a small current, the control component like Relay,timer,phase failure they have contacts that take up to 10Amps, those components rating is standard.
      It's only contactors that need sizing because they take different power sizes.

  • @moseswainainawainaina2353
    @moseswainainawainaina2353 4 роки тому

    I like your channels bro

  • @max_pherd2723
    @max_pherd2723 2 роки тому

    Thanks for this video

  • @mwanawahakaemmanuel7232
    @mwanawahakaemmanuel7232 2 роки тому

    How can it be connected because it was not shown

  • @samuelnjenga9994
    @samuelnjenga9994 3 роки тому

    Nice video. Educative🤙

  • @philipamosu4970
    @philipamosu4970 Рік тому

    Can it work if I supply 3phase voltage monitor relay with single

    • @electreca1
      @electreca1  Рік тому

      Yes, it can work for both single and three phase.

  • @flashvideos5602
    @flashvideos5602 4 роки тому

    If it latched to phase sequence failure how to reset it?

  • @joshuawoolridge8378
    @joshuawoolridge8378 3 роки тому

    Great video, keep it up!

  • @bonaventureedeh7300
    @bonaventureedeh7300 2 роки тому

    you did not explain how the threshold is set in their percentage in case of low and high voltage.

  • @godfreylawrencerono6947
    @godfreylawrencerono6947 3 роки тому

    good work bro

  • @georgeadeka7984
    @georgeadeka7984 2 роки тому

    Good work

  • @umangelectricalcontractors1133
    @umangelectricalcontractors1133 3 роки тому

    Please explain about how to connect ATS to generator controller.

  • @max_pherd2723
    @max_pherd2723 2 роки тому

    Please can you how to build control panels

    • @electreca1
      @electreca1  2 роки тому

      Video will come soon...…. thanks for watching

  • @danielmwema6798
    @danielmwema6798 3 роки тому

    Good video. I wanna learn more about control circuits. How can i contact you

    • @electreca1
      @electreca1  3 роки тому +3

      Contact me here info@electrecasolutions.com

  • @heshanshibry6575
    @heshanshibry6575 3 роки тому

    Hi bro this video is great but I have problem in my blue phase coz the blue phase always burns out what's reason for that can I have answer please. Coz in our whole estate the blue phase burns so I'm finding a answer to solve this issue.

    • @electreca1
      @electreca1  3 роки тому +2

      There may be 2 reasons
      1)Overload
      Try to check the load(current at full load)
      If the Blue phase is current the highest current consider balancing.
      If balancing is not possible then consider changing the load cable to size that capable to support the demand.
      2) Loose connection
      Be sure that connection that phase is tight and sound, any current carrying conductor carrying any amount of current if not tighter you have your cable burn.
      Check those two it will help.

    • @heshanshibry6575
      @heshanshibry6575 3 роки тому

      @@electreca1 thanks bro. And if possible is there way to contact via email or something if I need more information about this blue phase.

    • @electreca1
      @electreca1  3 роки тому +1

      @@heshanshibry6575 electreca.workshop@gmail.com

  • @dennisdenock7354
    @dennisdenock7354 4 роки тому

    Thanks for the explanation

  • @denofilms2438
    @denofilms2438 Рік тому

    I want control circuit

  • @engineeringvedios3130
    @engineeringvedios3130 3 роки тому

    Where is the control circuit?

  • @dedankimathi7136
    @dedankimathi7136 3 роки тому

    Can I contact you on email?