Delta MS300 External Terminal Operation Control

How to configure operation commands (run/stop/direction) for the control terminals on the Delta MS300.
downloadcenter.deltaww.com/en...

[@jakubzborowski6426]

Thank's, very helpfull video. Greetings from Sohbi

[@pauldering6539]

thank you very much.

[@ReyRelacion]

How to use the multi function relay output and what are the parameters thats need to set up? thank you.

[@cerita-ceritanabi3343]

Hi, I would like to ask a question. How to save our parameter setting at ms300? because I when I was turn off the inverter and tried to running again, the inverter need seeting again

[@MrBibinkk]

Sir i need to work this drive as a counter is it possible.. I tried but it didn't work

[@julioarias260]

Hello there. Can this VFD be controlled by an RC-01 accesorie ? Thanks

[@controlmate75]

can we take out the digital panel and use an extension wire or something so you can transfer the digital panel on the door of the main panel?

[@deltavfd6406]

Yes there is a keypad extension cable. The part numbers are in the accessories section of the manual.

[@raynelson3404]

I am wanting to run a vacuum pump for my cnc table. I was to told split the wire from the vacuum on switch and put it on m1 and vcm. Is this a safe method to run the drive?

[@deltavfd6406]

As long as it is a dry contact from MI1 - DCM and no additional power given to the drive control terminals, then yes.

[@jimmontgomery8982]

Thank you for your video. I'm needing parameter setting information for using an external braking resistor. Can you help?

[@deltavfd6406]

Hello, check parameters 06-01 and 07-00. Search for "brake resistor" in the manual pdf.

[@0Saints0Photography0]

Hi Can you do a video of how to connect the MS300 to use a 24v pulse to increase and decrease the frequency if possible?

[@deltavfd6406]

Using an external 24VDC input, see the control terminal wiring fig 6-5 in the manual.
Pulse input - the frequency of the pulses determines the speed. Check the description in parameter 10.16
External Up / Down - 00.20, 02.01 ~ 02.07 set to 19 and 20

[@mattchu79]

Can I bypass it by connecting a wire from MI1 to DCM bcuz I want it to run as soon as I activate the external switch that provides power to it

[@deltavfd6406]

Yes, also check 00.21 for external terminals and 02.35 setting to enable it

[@pds4927]

Hi, can you do a video on how to configure the ms300 to a lathe machine(Grizzly / Powermatic) using external switches/buttons to run the run/forwar/stop/reverse

[@stevelillie4597]

Hi pds4927. I'm Steve. I am trying to do just that..get an MS300 inverter to work on a PM 3520B. Did you ever have any luck configuring it with your lathe? I'm desperate. There are many more options than the original S inverter.

[@fungelelanimaster8668]

❤️ 💞

[@mrbonah8561]

What about if the wires are 5. Control nob has 3 wires. Start and stop has 2 wires. How can I connect it

[@deltavfd6406]

The potentiometer is covered in a separate video on connecting analog input.

[@user-fx8mv6jr1y]

Do you do consulting?

[@hapzc.j.]

fan not function how to

[@r.dmotorcontrolworks5066]

Hellow sir...can you pls create video tutorial about 4 20ma using ms300..tnx

[@deltavfd6406]

Hi, for 4-20mA use the ACI terminal as signal and ACM terminal as common. For speed reference, 03.00 = 0, 03.01 = 1, 00.20 = 2. For PID feedback, 03.01 = 5.