I am in the market for a Harley this year....I like the 2017 better than the 2018 except I am not so sure all the bad things I read about the twin cam 103....plastic tensioners, weak oil pumps, chain driven cams, crank pins coming loose....I think all this is fixable by simply switching to gear drive cams, upgrading oil pump and welding the crank pin.. and good maintenance practices.. I see so many of your videos so many people have the breakout with twin cam 103....I wonder what is your experience and what you see with your friends over there with the reliability of that engine??? any help or suggestions before I buy? I appreciate any feedback from anyone in this regard...cheers!!.
Mich würde mal interessieren was mit der Zylinderentlüftung passiert ? Und soweit ich weiß werden erst die Beiden Entlüftungsschrauben angezogen und dann die drei um die Ansaugöffnung......
Hi, just fitted a big sucker to my FXSTC, what did you clip onto the wiring plug with the red and yellow wires? Mine didn't come with that? Is it just a blanking plug?
It looks like the two main bolts at top have breather nipples on them, with pipes attached? These are replaced with closed bolts so that function is removed - what is this for?
Yes the breather bolts have a small hole in them where they screw in and on the side is a hole that channels through the filter housing. There is another youtube video that shows the bolts with the hole on the side and the small hole on the inside. The crankcase will be able to breath.
nothing too crazy, but enough to recognize the theme song. On a side note, I was referring to your video to setup my Big Sucker and on minute 6:15 the instructions are a tad misleading, as the set screws should be screwed to the stand offs first and then to the back plate of the intake. Doing as per your video, both screws on the right side will go all the way in and never lock. I called Arlen Ness and that's how I got the instructions cause at first, I thought I had bought the wrong parts. Just thought I'd share it with you, you can note that on that specific part of the video :)
lol. normalerweise nimmt man einen kleinen akku schraubenzieher und zieht es mit einem drehmoment dann an. billig billig, es hat auch eine montageanleitung immer dabei. aber gut,dass es doch noch leute gibt,die sowas ins netz stellen ✌👏
ich auch an meiner, aber warum so ikeaimbussbruns nehmen,wenn es mit dem akku schrauber und bits sicherer geht? vor allem besteht die gefahr nicht,dass man die schrauben innen rund macht. nur ein tipp von mir, der über 30 jahre automechaniker ist, und auch an meiner hd schraubt.
I am in the market for a Harley this year....I like the 2017 better than the 2018 except I am not so sure all the bad things I read about the twin cam 103....plastic tensioners, weak oil pumps, chain driven cams, crank pins coming loose....I think all this is fixable by simply switching to gear drive cams, upgrading oil pump and welding the crank pin.. and good maintenance practices..
I see so many of your videos so many people have the breakout with twin cam 103....I wonder what is your experience and what you see with your friends over there with the reliability of that engine??? any help or suggestions before I buy? I appreciate any feedback from anyone in this regard...cheers!!.
what about the electric connection, surely you aren't just going to leave it hanging there? Bike looks fantastic by the way! Mike P in UK
Thank you so much. I was so lost without you.
Mich würde mal interessieren was mit der Zylinderentlüftung passiert ?
Und soweit ich weiß werden erst die Beiden Entlüftungsschrauben angezogen und dann die drei um die Ansaugöffnung......
How do you get blood stains out of carpet? Asking for a friend.
This will fit an 97 sport with an Evo right it has a CV carb
Excellent video of this installation!!!!
Any reason why you use thread lock for only specific screws and not all?
Hi, just fitted a big sucker to my FXSTC, what did you clip onto the wiring plug with the red and yellow wires? Mine didn't come with that? Is it just a blanking plug?
mine either, just got it. did you figure it out or find something?
Bitte mehr von diesen kleinen Filmchen wie man was selber machen kann !!! 5****
It looks like the two main bolts at top have breather nipples on them, with pipes attached? These are replaced with closed bolts so that function is removed - what is this for?
The replacement bolts are hollow banjo bolts and the air is routed thru channels in the filter housing.
Je peux installer ce filtre même si je n'ai pas fais le stage 1 ?
Merci d'avance
What exhaust manifold and throttlebody set up is that?
With that music, I was waiting for the money shot...
Chinolyn, thanks for the ebay link re the fault code eliminator plug, much appreciated+++
have a question do u not need to put breather bolts on these intake kit
The Arlen Ness bolts are hollow breather bolts and feed back into the throttle body
Thanks for the video!
Very good video. Great.
what was that plug
03:56 This is a sensor? what is your function?
Are those breather bolts hollow? I am looking at ordering this same intake for my bike and can not seem to find much info thank you.
I was thinking the exact same thing. They have to be. You will blow a gasket if the crankcase cant breath
Yes the breather bolts have a small hole in them where they screw in and on the side is a hole that channels through the filter housing. There is another youtube video that shows the bolts with the hole on the side and the small hole on the inside. The crankcase will be able to breath.
Wenn der ´ne Liter Flasche Loctite gehabt hätte, wäre die wohl auch leer gewesen...
The Butler did it.
Good music
Thanks, great video but not sure about the Porno music?
I thought the same. Great vid with soft porn music on the background hahaha
nothing too crazy, but enough to recognize the theme song.
On a side note, I was referring to your video to setup my Big Sucker and on minute 6:15 the instructions are a tad misleading, as the set screws should be screwed to the stand offs first and then to the back plate of the intake. Doing as per your video, both screws on the right side will go all the way in and never lock.
I called Arlen Ness and that's how I got the instructions cause at first, I thought I had bought the wrong parts.
Just thought I'd share it with you, you can note that on that specific part of the video :)
อยากขับมั้งจัง
Damm didn't even get to hear it 🤔
lol. normalerweise nimmt man einen kleinen akku schraubenzieher und zieht es mit einem drehmoment dann an. billig billig, es hat auch eine montageanleitung immer dabei. aber gut,dass es doch noch leute gibt,die sowas ins netz stellen ✌👏
ich auch an meiner, aber warum so ikeaimbussbruns nehmen,wenn es mit dem akku schrauber und bits sicherer geht? vor allem besteht die gefahr nicht,dass man die schrauben innen rund macht. nur ein tipp von mir, der über 30 jahre automechaniker ist, und auch an meiner hd schraubt.
aber eines muss ich dir lassen, scharfes bild video!!
that is the best porn music I have heard in a while.
bmw