FINALLY! A short and very informative video! Getting ready to hang trim and was going to use that to justify a nail gun. But I had NO CLUE as to what I needed. Thanks. I have a combination stapler/brad nailer, but I knew those brads would be too short for my application. Now I know what to buy.
Good vid. Short and to the point. I was considering getting a framing nailer (which I used a lot when I was building houses), a brad nailer, and a pin nailer now that I'm gearing up to retire and will be trying different projects in my shop. This saved me some money. I'll get the framing and brad nailers, but it's clear for my needs that I can forgo the wire nailer.
Framing nailers are a whole other video we should shoot! Most people if they could only choose 1 of these 3 will go with brad nailer because it can do a little of everything. Of course normally the job/project right in front of you will dictate the tool you buy next off the wishlist.
What a great video! I refinish furniture which has not always been "gently used", so I need to know how to restore some things. Your video really helped me out. Thanks!
Great video! Was trying to decide which to get for my first cordless nailer, Brad or Finish. Can't afford mouth at that moment, so wanted the most versatile. This helped.
Thanks for explaining the different types of nail-guns !!! But I am really worried about how to remove those nails-without-a-head, when I want to take something apart again...🤔
Great video. I wasn't really able to gauge which nailer I would need. But if I want to make a cabinet on wheels for a 50 pound air compressor should I use the Finish nailer with 15gauge nails?
Great video! Could you use a Pin Nailer for accent wall designs when using 1/2" or 3/4" thick pine or MDF and CA glue is used where the all the peaces joint together?
You certainly could! Pin nailers are perfect for accent wall designs, especially very small or delicate ones! Anything bulkier though and you'd best be looking at a brad nailer to get the job done!
As a weekend DIY'er that will occasionally build furniture or do accent walls, etc - would the brad nailer be my best bet? since it is the most versatile? I did want to do crown molding eventually though and it sounds like the brad nailer may not work for my needs.
Corded nailers are not very popular, they jumped right from air hoses to battery powered and never looked back. Metabo HPT does make an adapter to use their battery tools with a plug but assume you’re looking to keep cost down vs adding an expensive accessory onto a battery tool.
Hey Gareth! That sounds about right to us! You may want to get a pin nailer if you're going to be putting some fancier accoutrements on it, but for your basic wardrobe a brad nailer should do the trick!
Always important to remember! Well, that and not crossing the streams, but sometimes you have to be a little flexible if you want to defeat Zuul and save New York! (The pointy end should still go away from you, Gozer commands it!)
@@OhioPowerTool” ….dogs and cats, living together! Mass hysteria!!!” Almost as important as not putting your yellow tools into red boxes. Just don’t do it, man. It’s just too big a risk.
What do you think: Is the finish nailer the best choice for installing timber weatherboards? I have a large Ecko framing gun (the Ultimate 90 gas framer), but that seems way too powerful.
Technically, you could use a Finish Nailer, but probably not the best choice. Those weatherboards could have some thickness to the material so your framing gun is better suited in my opinion. Could shop for a battery powered Framing Nailer if you're wanting something a little lighter.
Hello. I’m doing board and batten as my first DIY home project. I got the 1” (3/4#) inch thick pine wood trim. I only have a brad nailer. What size of nail do you recommend me use? And should I use a wood glue to well secure the trim to the wall? Or would you recommend using a finish nailer?
I would suggest a 1 to 2 inch, in length, 18-gauge brad nails. Also wood glue is a great addition for stability while you're installing. While a finish nailer may offer more holding power, the brad nailer you have will do just fine!
Brad nails would probably be your best bet if you're working with metal sheets; pin nails would definitely be too small, and while you'd have more than enough power with a finish nailer, the brad should get the job done and be able to save you some cash!
Yes they do! Here is the link to our website: www.ohiopowertool.com/milwaukee-tool-2841-20 There is also a kit available as well www.ohiopowertool.com/milwaukee-tool-2841-21ct
It depends on the thickest of your wood, so a Brad Nailer would be best for delicate and thin materials and a Finish Nailer would be best for slightly thicker material.
Wonderful video. That was very informative and you made the content easy to understand. I'm new to powered nailers and while I know there are various products on the market, I don't have a solid working knowledge of the options, depending on the job at hand. Thank you for explaining the when's, why's and likely outcomes when deciding which tool to use.
Hey Franklin! Glad we were able to help! Please feel free to reach out if there are any questions we can help to answer and best of luck with your powered nailer journey!
OK I'm refinishing a couple of rooms in my house. I'm just gonna be doing the trim work so should I use a finished nailer or a Brad nailer? I'm a little confused still I know the finished nail. I would probably be the better of the 2 tools but I also tend to overpurchase. So would the brad naylor be sufficient as what i'm asking
Yes! A brad nailer should be able to do the trick for you; a finish nailer would do the job just as well, but if you want to save a little bit of money, go with the brad!
Brad nails may not offer the best holding power, we recommend a larger nail or fastener! These include finish nails or even screws - both can provide more holding power than brad nails.
Good informative video. Curious about fastening thin and soft cedar shingles, into oak framing. The brad nailer shoves the brads thru the thin cedar, and doesn't secure. Would a finish nail have a bigger head, and secure better? Anyone? Thanx.
Using a finish nailer is a better option because of the reasons you stated, however because you are still working with delicate wood, you'll still have to be careful not to split the wood. You can also pre-drill pilot holes with a drill bit slightly smaller in diameter than the finish nails, this can sometimes help!
Hi, for fencing jobs we suggest you use a finish nailer. It can provide more strength and holding power to drive larger nails to secure fence boards and panels.
The only thing about not having a place that you can take classes about power tools is meeting cool people on you tube that help more often then not. The only draw back is that I only find videos that 2 yrs old or more, and by that time, no one answers your questions anymore 😮💨.
@@OhioPowerTool Absolutely love mine. They’ve also been killing it on their Gen 2 Nailers; 18 ga Brad, 16ga, and 15ga Finish. Solid and reliable. In all honesty, though, bang for the buck, the Craftsman ones are also not bad. Bulky as all get out, but not bad. They have a great belt hook and hang well on a belt or tool belt if you need to climb a ladder.
In general, a thicker nail (lower gauge) will provide more holding power than a thinner one. The increased thickness of a 15-gauge finishing nail means it can typically withstand greater stress and pullout forces compared to a 16-gauge nail
Not really I use my Brad nailer to do everything from trim to building cabinets. My opinion it’s the best of both worlds. If you won’t be using it much ryobi makes an 18g that’s a nice sweet spot for only $89.
Correct! We're focusing on battery-powered nailers in this video; for the most part, the information translates across the board! The pneumatics give the nailer a boost in speed, allowing you to get through a project quicker than you would with a cordless one; however, you're then at the mercy of cords and hoses and the like, whereas a cordless nailer gives you the freedom of movement throughout the jobsite without having to lug a whole setup around!
Hey David! Your best bet for baseboards would likely be a finish nailer, just due to the holding power on the nails themselves. You may be able to get away with a brad nailer, but definitely not a pin nailer. Hope that helps!!
Oh sure! Now, keep in mind that the brad nails won't have as much holding power as finish nails, so you may find yourself using more of them to fully anchor the baseboards to the wall. Start small and make sure you angle at least the first set of nails to give yourself a little room for extra just to be safe, and good luck!
What an excellent question! The answer to this depends somewhat on what wood you're planning on using, as well as if they're purely for decoration or if you plan on making them functional. For the most part, you should be able to get away with a fairly strong wood glue or even some longer hand screws if the wood is pliable enough, though if you're set on using a nailer, brad nails would be the way to go! Remember that the orientation of the nailer is important so the nails don't go shooting into or out of the birdhouse at awkward angles, and if these are going to be functional for birds, be sure to add some ventilation and drainage features to make it comfortable for them and have fun!
@@OhioPowerTool hey thanks. See I’m a quadriplegic so using a drill and screws is to difficult. I do have good arm function and limited hand function and believe I can manipulate the nailer well enough to use. I’m planning to build some log cabin style birdhouses using locally sourced limbs and such. Might make a few other designs as well though. I should be able to set the nail depth on the nailer though right. If not I should be able to adjust my air pressure to reduce penetration I think. I appreciate you getting back with me though.
That sounds like a phenomenal project! You should definitely be able to get away with using a brad nailer for that, and we'd also recommend having some spare wood putty or glue on hand to seal over any nail holes that you don't want exposed. Best of luck to you, and if there's anywhere that you can post the finished product, we'd love to see them!!
Generally, they are! They're all used for fastening, or adjoining, pieces of wood together. If, however, you try using a pin nailer for, say, a baseboard project, you'll find the holding power in a pin nailer significantly lacking. Conversely, if you try using a finish nailer for some decorative trim, the nail will at least damage, if not completely obliterate, the piece you're working on. It's sort of like choosing the correct sized screwdriver; too large, and you can strip the screw if the head will even fit, too small and you won't get any leeway!
FINALLY! A short and very informative video! Getting ready to hang trim and was going to use that to justify a nail gun. But I had NO CLUE as to what I needed. Thanks. I have a combination stapler/brad nailer, but I knew those brads would be too short for my application. Now I know what to buy.
This video answered every question I had when I looked for a video like this
“the pointy end goes away from you”. As soon as I heard that I knew I was watching the right video! Lol
Thanks!
Thanks! Just what I needed
Awesome video, thank you!
Thanks. I’m finishing a home project.
Quality content. Thanks for uploading.
Thanks, great explanation!
Super helpful - thanks!
Awesome video!! Thanks
Good vid. Short and to the point. I was considering getting a framing nailer (which I used a lot when I was building houses), a brad nailer, and a pin nailer now that I'm gearing up to retire and will be trying different projects in my shop. This saved me some money. I'll get the framing and brad nailers, but it's clear for my needs that I can forgo the wire nailer.
Framing nailers are a whole other video we should shoot! Most people if they could only choose 1 of these 3 will go with brad nailer because it can do a little of everything. Of course normally the job/project right in front of you will dictate the tool you buy next off the wishlist.
What a great video! I refinish furniture which has not always been "gently used", so I need to know how to restore some things. Your video really helped me out. Thanks!
Glad we could help Catherine!!
Thank You.
This is exactly the video I needed.
Thanks Walt! Glad we were able to help!!
Great video! Was trying to decide which to get for my first cordless nailer, Brad or Finish. Can't afford mouth at that moment, so wanted the most versatile. This helped.
Glad we could be of assistance! Feel free to let us know if you have any further questions that we can help with!!
Just what I needed!
Glad we were able to help, Carole!!
Awesome info
Crushed it. Thanks!
Glad you enjoyed, thanks for taking the time to check us out!
Super good video. Thanks! I am doing re-flooring. I guess I should choose Brad nailer for putting back skirting(Moulding), correct? Thanks.
Great Update
Thanks Jamal! Glad you dug it!!
Thanks for explaining the different types of nail-guns !!!
But I am really worried about how to remove those nails-without-a-head, when I want to take something apart again...🤔
Thank you thank you thank you
Great video. I wasn't really able to gauge which nailer I would need. But if I want to make a cabinet on wheels for a 50 pound air compressor should I use the Finish nailer with 15gauge nails?
Great video! Could you use a Pin Nailer for accent wall designs when using 1/2" or 3/4" thick pine or MDF and CA glue is used where the all the peaces joint together?
You certainly could! Pin nailers are perfect for accent wall designs, especially very small or delicate ones! Anything bulkier though and you'd best be looking at a brad nailer to get the job done!
Finish Nailer -> Max gauge. Name makes no sense whatsoever 🤯
"Finish(ed)", aka: done, not coming out, not coming back, finished.
Well they are the largest for finish style and fine carpentry. But roofing and framing nailers are still way bigger
What would be the best all around for a travel trailer? Some panels and trim are starting to separate
I’m planning on doing a slat wall in my bedroom with a 2” thick slat, which would be better a Brad nailer or a finishing nailer?
As a weekend DIY'er that will occasionally build furniture or do accent walls, etc - would the brad nailer be my best bet? since it is the most versatile? I did want to do crown molding eventually though and it sounds like the brad nailer may not work for my needs.
How can I nail aluminum soffit fasia without having the nail head sink in?
How much your diamond core bit?
Thank you for the explanation of the differences. Where can I find a 16 gauge finish nailer that is electric. You know that runs on household current?
Corded nailers are not very popular, they jumped right from air hoses to battery powered and never looked back. Metabo HPT does make an adapter to use their battery tools with a plug but assume you’re looking to keep cost down vs adding an expensive accessory onto a battery tool.
Excellent video cheers. So if you're putting together a wardrobe made of 18mm mdf you would use the Brad nailer? Thank you.
Hey Gareth! That sounds about right to us! You may want to get a pin nailer if you're going to be putting some fancier accoutrements on it, but for your basic wardrobe a brad nailer should do the trick!
@@OhioPowerTool excellent thanks a lot for the information!!
Best of luck!!
😮 Pointy end goes AWAY from you!
“Important safety tip! Thanks Egon.”
Always important to remember! Well, that and not crossing the streams, but sometimes you have to be a little flexible if you want to defeat Zuul and save New York!
(The pointy end should still go away from you, Gozer commands it!)
@@OhioPowerTool” ….dogs and cats, living together! Mass hysteria!!!”
Almost as important as not putting your yellow tools into red boxes. Just don’t do it, man. It’s just too big a risk.
@@jamesmocharski4803 I put red tools in black and yellow boxes so I can find them. Same with fasteners. You need to see what’s in there.
I have small staples: 3/6" wide X 5/8" deep, I believe them to be about 21 gauge, square head - what will shoot these staples?
I have all 3 - 15ga, 18ga, and 23ga.
Which cordless nailer is the best for running around in parking lots & shooting nails into tires?
I like your question, cos im also looking for that one in particular
huh???
What do you think: Is the finish nailer the best choice for installing timber weatherboards?
I have a large Ecko framing gun (the Ultimate 90 gas framer), but that seems way too powerful.
Technically, you could use a Finish Nailer, but probably not the best choice. Those weatherboards could have some thickness to the material so your framing gun is better suited in my opinion. Could shop for a battery powered Framing Nailer if you're wanting something a little lighter.
Hello. I’m doing board and batten as my first DIY home project. I got the 1” (3/4#) inch thick pine wood trim. I only have a brad nailer. What size of nail do you recommend me use? And should I use a wood glue to well secure the trim to the wall? Or would you recommend using a finish nailer?
I would suggest a 1 to 2 inch, in length, 18-gauge brad nails. Also wood glue is a great addition for stability while you're installing. While a finish nailer may offer more holding power, the brad nailer you have will do just fine!
Does it work on metal sheets?
Brad nails would probably be your best bet if you're working with metal sheets; pin nails would definitely be too small, and while you'd have more than enough power with a finish nailer, the brad should get the job done and be able to save you some cash!
I heard the Ridgid nail guns are very reliable for morning wood.
Brushless motor
We’ve heard good things about Ridgid as well. Not a brand we sell (not the Ridgid Orange at least) but part of TTI family with Mikwaukee Tool.
Does the Milwaukee have angular nailing capabilities for things like corner molding?
Yes they do! Here is the link to our website: www.ohiopowertool.com/milwaukee-tool-2841-20
There is also a kit available as well www.ohiopowertool.com/milwaukee-tool-2841-21ct
What's the best nailer to use when doing base boards around the house?
It depends on the thickest of your wood, so a Brad Nailer would be best for delicate and thin materials and a Finish Nailer would be best for slightly thicker material.
Wonderful video. That was very informative and you made the content easy to understand. I'm new to powered nailers and while I know there are various products on the market, I don't have a solid working knowledge of the options, depending on the job at hand. Thank you for explaining the when's, why's and likely outcomes when deciding which tool to use.
Hey Franklin! Glad we were able to help! Please feel free to reach out if there are any questions we can help to answer and best of luck with your powered nailer journey!
OK I'm refinishing a couple of rooms in my house. I'm just gonna be doing the trim work so should I use a finished nailer or a Brad nailer? I'm a little confused still I know the finished nail. I would probably be the better of the 2 tools but I also tend to overpurchase. So would the brad naylor be sufficient as what i'm asking
Yes! A brad nailer should be able to do the trick for you; a finish nailer would do the job just as well, but if you want to save a little bit of money, go with the brad!
I'm covering a wall with 3/4 inch thick pine. I'll need to drive thru drywall to get to the frame. Does brad nails have enough strength?
1x6x10 - pine
Brad nails may not offer the best holding power, we recommend a larger nail or fastener! These include finish nails or even screws - both can provide more holding power than brad nails.
what would work best for building a sturdy privacy fence? both for the 2x4s as well as the slats?
Probably a fencing nail gun.
@@sypher0101 😂
One not covered here - a framing nailer.
Good informative video. Curious about fastening thin and soft cedar shingles, into oak framing. The brad nailer shoves the brads thru the thin cedar, and doesn't secure. Would a finish nail have a bigger head, and secure better? Anyone? Thanx.
Using a finish nailer is a better option because of the reasons you stated, however because you are still working with delicate wood, you'll still have to be careful not to split the wood. You can also pre-drill pilot holes with a drill bit slightly smaller in diameter than the finish nails, this can sometimes help!
@@OhioPowerTool thanks for the reply. :)
Which one to use for fencing?
Hi, for fencing jobs we suggest you use a finish nailer. It can provide more strength and holding power to drive larger nails to secure fence boards and panels.
The xgt pinner is the best,I'll be waiting on the brad..😇
Hopefully we'll be getting one soon! They've already got them overseas, so fingers crossed for an announcement soon!
@@OhioPowerTool great! I didn't know they had one overseas, thanks for the info!
Hi need some help
What's the best for making cabinets carcasses (capentry
You'd probably be best off with a brad nailer! They're quite versatile and would be best for all around cabinetry!
The only thing about not having a place that you can take classes about power tools is meeting cool people on you tube that help more often then not. The only draw back is that I only find videos that 2 yrs old or more, and by that time, no one answers your questions anymore 😮💨.
We try to stay on top of the questions, if we're not hitting them for anyone here, can always give us a call 614-481-2111. Thanks for watching!
Which is best for securing 1/4 round to baseboard?
ua-cam.com/users/shorts0yZNL9RBHMc
I'm gonna take the Milwaukee cause the angle, but blame the blue looks all accessible
That Milwaukee's got a very comfortable angle to it, it's a fantastic tool!
@@OhioPowerTool Absolutely love mine.
They’ve also been killing it on their Gen 2 Nailers; 18 ga Brad, 16ga, and 15ga Finish.
Solid and reliable.
In all honesty, though, bang for the buck, the Craftsman ones are also not bad.
Bulky as all get out, but not bad. They have a great belt hook and hang well on a belt or tool belt if you need to climb a ladder.
Is there really that much of a difference in holding power between a 16g and 15g finishing nails?
In general, a thicker nail (lower gauge) will provide more holding power than a thinner one. The increased thickness of a 15-gauge finishing nail means it can typically withstand greater stress and pullout forces compared to a 16-gauge nail
Not really I use my Brad nailer to do everything from trim to building cabinets. My opinion it’s the best of both worlds. If you won’t be using it much ryobi makes an 18g that’s a nice sweet spot for only $89.
There is something about some nailers being pneumatic i.e use air pressure as power source. You did not go into that detail.
Correct! We're focusing on battery-powered nailers in this video; for the most part, the information translates across the board! The pneumatics give the nailer a boost in speed, allowing you to get through a project quicker than you would with a cordless one; however, you're then at the mercy of cords and hoses and the like, whereas a cordless nailer gives you the freedom of movement throughout the jobsite without having to lug a whole setup around!
Do you recommend it to put baseboards?
Hey David! Your best bet for baseboards would likely be a finish nailer, just due to the holding power on the nails themselves. You may be able to get away with a brad nailer, but definitely not a pin nailer. Hope that helps!!
Oh thank you so much
Do you think that can I use the Dewalt DCN680 18GA?
Oh sure! Now, keep in mind that the brad nails won't have as much holding power as finish nails, so you may find yourself using more of them to fully anchor the baseboards to the wall. Start small and make sure you angle at least the first set of nails to give yourself a little room for extra just to be safe, and good luck!
Oh thank you so much I appreciate your response you do an excellent job
I’m looking to get something simply to build some bird houses. Should I go brad or pin?
What an excellent question! The answer to this depends somewhat on what wood you're planning on using, as well as if they're purely for decoration or if you plan on making them functional. For the most part, you should be able to get away with a fairly strong wood glue or even some longer hand screws if the wood is pliable enough, though if you're set on using a nailer, brad nails would be the way to go! Remember that the orientation of the nailer is important so the nails don't go shooting into or out of the birdhouse at awkward angles, and if these are going to be functional for birds, be sure to add some ventilation and drainage features to make it comfortable for them and have fun!
@@OhioPowerTool hey thanks. See I’m a quadriplegic so using a drill and screws is to difficult. I do have good arm function and limited hand function and believe I can manipulate the nailer well enough to use. I’m planning to build some log cabin style birdhouses using locally sourced limbs and such. Might make a few other designs as well though. I should be able to set the nail depth on the nailer though right. If not I should be able to adjust my air pressure to reduce penetration I think. I appreciate you getting back with me though.
That sounds like a phenomenal project! You should definitely be able to get away with using a brad nailer for that, and we'd also recommend having some spare wood putty or glue on hand to seal over any nail holes that you don't want exposed. Best of luck to you, and if there's anywhere that you can post the finished product, we'd love to see them!!
@@OhioPowerTool do you guys have a Facebook page?
@@LeaveItToTheWolves We do! We're @ohiopowertool on Facebook, Twitter, Instagram, and TikTok!
🔄
I'm still confused. They all seem to be used for the same applications.
Generally, they are! They're all used for fastening, or adjoining, pieces of wood together. If, however, you try using a pin nailer for, say, a baseboard project, you'll find the holding power in a pin nailer significantly lacking. Conversely, if you try using a finish nailer for some decorative trim, the nail will at least damage, if not completely obliterate, the piece you're working on. It's sort of like choosing the correct sized screwdriver; too large, and you can strip the screw if the head will even fit, too small and you won't get any leeway!
so you’re saying to buy all three
If you need all 3!
I wish you spent more time, going deep on the explanation, to be honest!!!
Hey KJ! Thanks for the feedback! What could we provide more details on?
Outdamnstanding video