How to set Preload on alpha 1 gen 1 (2) bravo
Вставка
- Опубліковано 29 сер 2024
- If interested in purchasing this product, visit our Amazon affiliate link below. I earn from qualifying purchases.
amzn.to/3G1aDLl
1. CDI inch pound torque wrench tutorial review
• CDI inch pound torque ...
2. Separate Mercruiser outdrive upper from lower unit
• Separate upper and low...
3. Remove U-joint gear bearing assembly from upper unit
• How to remove mercury ...
4. Build assemble outdrive upper unit stand
• Mercruiser outdrive en...
5. Best outdrive lower unit stand - assemble review
• Build assemble outdriv...
6. How to assemble 6ft Craftsman workbench
• Assemble 6ft Craftsman...
7. Adding drawers to workbench
• Assemble & add drawers...
8. How to install Swivel Vise onto workbench
• BENCH VISE - Install S...
Must say though.... I have thought that your series is the most complete! I personally just ripped my gen 2 apart and i reference your vids very often. Excellent work mate!
If interested in purchasing this product, visit our Amazon affiliate link below. I earn from qualifying purchases.
amzn.to/3G1aDLl
1. CDI inch pound torque wrench tutorial review
ua-cam.com/video/-HVqh4BG0yU/v-deo.html
2. Separate Mercruiser outdrive upper from lower unit
ua-cam.com/video/sZHDYu4ee6o/v-deo.html
3. Remove U-joint gear bearing assembly from upper unit
ua-cam.com/video/FOeyTR19SXU/v-deo.html
4. Build assemble outdrive upper unit stand
ua-cam.com/video/gLBQvjiYaEk/v-deo.html
5. Best outdrive lower unit stand - assemble review
ua-cam.com/video/UEpwRnimMoc/v-deo.html
6. How to assemble 6ft Craftsman workbench
ua-cam.com/video/j-EMLt-Z1CQ/v-deo.html
7. Adding drawers to workbench
ua-cam.com/video/bc9lNnXUlsA/v-deo.html
8. How to install Swivel Vise onto workbench
ua-cam.com/video/2tSMXLuYVkw/v-deo.html
Hey Mike... I think you may have overloaded the bearings with 61 in-lbs of force. That wrench you are using is newton meters.
I wonder if he saw this comment. Seems like you are correct.
I was about to order this torque wrench and realized yes he is referring to inch pounds but the dial is showing newton meters. This would not be a good wrench for this project.
You mentioned on the slip fit that the nut gets torqued to 80 pounds. Is that foot pound, or inch pounds? If this is the procedure, then why even buy the special nut and washer if the old bearings and gears are being reused?
Great Vid Thanks
I installed a used good set if bearings and gears in my alpha one 1988. Now it whines . I did not do this preload. I did not use a torque wrench . I could turn the shaft with my hand prior to installing. Can'timagine it's too loose??.
Thanks for watching. It’s possible that it’s due to the preload being slightly off.
Improper re-shimming for the change in gears and bearing can cause this.
@@DIYwithMichaelBorders I used the shims that were in it already. Gonna pull the drive.
@@MikeSsuncoasttrains
Keep us posted. Do you plan on performing preload procedure?
@@DIYwithMichaelBorders I think It's coming from the gear set. The lash looks good and it doesn't even get warm.
@@MikeSsuncoasttrains
Awesome, looking forward to hearing back from you. 👍
Jou forget the clamp in the middele of the bearing 🤦🏻♂️
Thanks for watching, it’s recommended to do so however we didn’t have a clamp readily accessible. Keep us posted on your project. 😎👍