There are many such video clips of differential gears being repaired, crankshafts, camshafts, etc, but how come we never see the engine running? How come we don't see what it's like six months from now? I have my doubts and I don't think I'd like to be around when the customer comes back asking for a refund. Alex Ivanov, below, no, it's not cast iron. It's cast steel, look at the swarf while it's being drilled. Cast iron swarf is granular, steel produces spirals. An HT welding rod will do it but then the pinning bolts should also be HT. But they would appear to be mild steel because they're galvanized. HT cap screws or hex sets are black as a rule.
Steel repairs are not supposed to last long but long enough for the other existing cracks to fail first, that is the economic for repair, it is meant to get the last ounce of use out of an otherwise full of cracks part
that is a cast iron crank that never welds, it will snap again along the welding seam. steel bolts have different thermal expantion and will cause bending forces inside, and which is more the bearing surfaces are riuned, there is no way to polish or ressurect them. the crank is trash. p.s.someone tell them to measure bearings instead of oil seal surface
it is forged. I am a machinist and the crank is probably at least 4140. rod most likely 7018. half the tensile strength of the crank. he didn't v it out, not that it would of help. no penetration and welding alloy steel. zero chance it will work.
ЛАДНО ЕЩЁ ПОРШНИ ГОРЕЛЫЕ С КОНСКОЙ ВЫРАБОТКОЙ В ОВАЛЬНЫЕ ЛЫСЫЕ ГИЛЬЗЫ ЗАСОВЫВАЮТ И СОБИРАЮТ ! НО КОЛЕН. ВАЛ ЛОПНУТЫЙ ВАРИТЬ И СЫРЫМИ БОЛТАМИ СТЯГИВАТЬ ЭТО КОНЕЧНО ТАЛАНТ !
Hola saludos desde Venezuela.. Que buen trabajo... pero no entiendo porque Reparan algo y al mismo Tienpo tratan de Dañar otro... se Devio Protejer los puños donde van laa conchas de Vancadas y de las Bielas ese Cromo es Muy Delicado.. para próximos trabajo protejalos exitos y muchas Felicidades... Exito Dios Bendiga esas Manos hombre luchadores...
C'mon. Don't be a hater. That was a legit repair. I've done that a bunch of times. Everything from big diesels to nascar engines. They all hold up perfectly. The only thing I would have done differently is use softer bolts. Those ones looked too hard. 😂😂😂😂
This is fake, that crank would snap straight away as the weld is in the area where the force is high. You can weld on cranks but not on a fracture like that. These guys are just doing this for a video the crank will never be used.
Anything can be "fixed"....but l guarantee that this crankshaft won't hold up once installed... l know how they abuse and overload their equipment in those countries.
@@ПашкаПашкович-д3ч ну да. Расскажи как и чего ты добился? Наверное, все нищие мечтают недоедать? Пацану из бедной семьи из умирающей деревни где нибудь в тайге, конечно, только захотеть и стоит, чтобы "всего добиться"
Nossa, esses caras são doidos. Da o maior trabalho tirar o motor, desmontar,retificar, montar de novo e colocar no lugar pra fazer uma gambiarra dessas, eu aposto que não dura nada. Eu achava que o Brasil era precário...
Hello ATO. That all looks like a carpenter fixing a table leg. Dowel pegs and all. This must be one of those scrap bin jobs where busted parts are “fixed” for the video. Sure hope Utube pays them well. On the other hand, that’s probably a crankshaft for a top fuel dragster. Maybe John Force Racing gets their cranks from ATO. Always wondered what those fender stickers stood for. Now we know.
That should last maybe a day or two. Operators in that part of the world routinely overload or otherwise operate their machinery well past reasonable parameters. Always.
Nothing amazing about it. This crankshaft is out of round, out of balance & the structural integrity has been compromised. Klinger.....you screwed the pooch on this one...GUARANTEED comeback!!
I suspect these guys have done this before.....ok would not happen in the west....but sometime we have to do what we have to do with what we have to hand. Yes I would like to see how it stand up in action....but at least they try.....maybe some are ok for a while and they are happy with that. If the could go to the dealership and get one off the shelf Im sure they would.
I appreciate what your saying, but at the end of the day there somethings that just cannot be repaired to a level required by the forces that are going to be applied. It's a matter of physics not economics.
I am proud of this man and hard work he puts in. But I won’t drive that car. The first downshift the load on flywheel will take the wheel true the car like saw blade . No way Wielding the cast crank on room temperature with stick rod damn
Ничего удивительного не увидел , у нас в России до сих пор так делают многие. Камазисты и не такое могут делать. У нас это считается, низкокласифицированный и дешёвый ремонт . Это и правда не надолго . Единственный плюс, что человек не без дела сидит.
I don't see how this repair will last, Is that crank even indexed? But the bolts that they are using, are they at least grade 8? Hmmm entertaining though.
Ничего более шокирующего на этом канале я ещё не видел!
Еще наверное молод не такое увидишь за свою жизнь,мудаки везде есть,еще не то сделают.
молодцы. теперь покрасить зеленой краской и выбросить.
There are many such video clips of differential gears being repaired, crankshafts, camshafts, etc, but how come we never see the engine running? How come we don't see what it's like six months from now? I have my doubts and I don't think I'd like to be around when the customer comes back asking for a refund. Alex Ivanov, below, no, it's not cast iron. It's cast steel, look at the swarf while it's being drilled. Cast iron swarf is granular, steel produces spirals. An HT welding rod will do it but then the pinning bolts should also be HT. But they would appear to be mild steel because they're galvanized. HT cap screws or hex sets are black as a rule.
hahaha only for return customers.
Because it doesn't work!!! This crankshaft will work to the first major load.
Steel repairs are not supposed to last long but long enough for the other existing cracks to fail first, that is the economic for repair, it is meant to get the last ounce of use out of an otherwise full of cracks part
What is the purpose of the 2 "pinning" bolts?
@@lindsaythomas2283 to increase the contact between two sides beyond just the seams
This is why everything is endlessly under repair
Теперь и умирать не страшно . Видел в жизни почти все .
that is a cast iron crank that never welds, it will snap again along the welding seam. steel bolts have different thermal expantion and will cause bending forces inside, and which is more the bearing surfaces are riuned, there is no way to polish or ressurect them. the crank is trash. p.s.someone tell them to measure bearings instead of oil seal surface
Also they can't set up degree rotation. Indian job.
Completely agree.
@@getov1147 pakistani, by dress
@@getov1147 they are Pakistanis
They just doing it for youtube views and subs, any low skill mechanic will know this is usless
Сижу на полу в гараже режу резьбы метчиком, а сам думаю , че там пацаны в Пакистане делают?
Họ đang chứng minh những gì anh học trong trường kỹ thuật cơ khí là sai bét cả !😁
😂😂😂
😆😆🤣😝😝😝
Ещё косынками надо усилить, чтобы дольше ходил.
суперклей и сода явно помогут
Ну не ужели они на столько тупые?я просто не очень в сварке и железе.....за каким то хером они пытаются сварить коленвал))))
как ни странно но в советские времена и у нас такое практиковали с 2 колен варили 1, только балансировать необходимо
@@konstantine_2217 ну не так похабно,как здесь...Такое купит только перекуп...
@@konstantine_2217 это рентабельно ?!
На совесть делают чтоб клиент далеко не уехал он обязательно к ним вернётся с благодарностью
или с пистолетом)))))
Хотелось бы увидеть,как на долго хватило этого вала? На запуск,или на два?
Ты не поверишь но на долго если в сервант поставить и не ронять.
Еще походит. Ну а развалится можно еще раз сваркой приварить
Such perfection! and it comes with a 3 mile or 30 minute warranty. Pure BS
I would call it a "wave" warranty, If you cannot see them waving it's out of warranty
Forty seconds, or forty meters, hic!
Работа может и отличная но бестолковая!
Wood glue works well too.
Надо было еще синей изолентой замотать, тогда точно долго проходит.
Ты привари мне как нибудь я домой приеду изолентой заматаю 😂
Блин всё варят у них наверное пластиковые и деревянные электроды есть и бетонные 😂😂
ну и резиновые тоже,мало ли шланг заварить.
а в аптеке электроды по мясу купить можно
Commedy gold !
That's probably one of their home made cast cranks which broke, it will break again for sure.
it is forged. I am a machinist and the crank is probably at least 4140. rod most likely 7018. half the tensile strength of the crank. he didn't v it out, not that it would of help. no penetration and welding alloy steel. zero chance it will work.
Видимо коленвал лопнул по сварному шву после предыдущего мастера, у которого были просроченные электроды
не скорей всего не было чугунных электродов,он резиновыми заварил.из-за этого и лопнул.
Ахах 😂😂😂
И насколько его хватит до первой нагрузки на двигатель
Поставят заведут, газу дадут и опять варить😂😂😂
ЛАДНО ЕЩЁ ПОРШНИ ГОРЕЛЫЕ С КОНСКОЙ ВЫРАБОТКОЙ В ОВАЛЬНЫЕ ЛЫСЫЕ ГИЛЬЗЫ ЗАСОВЫВАЮТ И СОБИРАЮТ ! НО КОЛЕН. ВАЛ ЛОПНУТЫЙ ВАРИТЬ И СЫРЫМИ БОЛТАМИ СТЯГИВАТЬ ЭТО КОНЕЧНО ТАЛАНТ !
@@ВасилийПупкин-ы4и8м ++ надо было проволкой замотать и еще походит
Это на авито...
@@acbdcd1897 КУПИЛ ТАКОЙ?
Hola saludos desde Venezuela..
Que buen trabajo... pero no entiendo porque Reparan algo y al mismo Tienpo tratan de Dañar otro... se Devio Protejer los puños donde van laa conchas de Vancadas y de las Bielas ese Cromo es Muy Delicado.. para próximos trabajo protejalos exitos y muchas Felicidades...
Exito Dios Bendiga esas Manos hombre luchadores...
Pure Comedy.
Yep, that crankshaft will make a good door stop, or boat anchor😆
C'mon. Don't be a hater. That was a legit repair. I've done that a bunch of times. Everything from big diesels to nascar engines. They all hold up perfectly. The only thing I would have done differently is use softer bolts. Those ones looked too hard. 😂😂😂😂
I'm pretty sure a crankshaft should not be welded and then be trusted to last.
This is fake, that crank would snap straight away as the weld is in the area where the force is high.
You can weld on cranks but not on a fracture like that.
These guys are just doing this for a video the crank will never be used.
But and the balance of This crankshaft , excelent and nice job congratulatiins
Работы нет, давай хоть кино поснимаем))). Для металлоприёмки)))
I cant imagine if it survive for a week. Anyway thankyou for your effort.
Here in Brazil, these crankshafts go to the foundry.
Anything can be "fixed"....but l guarantee that this crankshaft won't hold up once installed... l know how they abuse and overload their equipment in those countries.
Loucura isso é aventura de mecânicos irresponsáveis, isso vai arrebentar fazendo um regaço no bloco, não gostaria de estar por perto,só Deus na causa.
да это чисто для видосов,для движухи канала на камеру делают,
а потом выкинут
النهاية لا زالت بها نقائص واضحة و المهم شكرا على العمل و الجهد المبذول
Просто жалко этих людей.
Điều kiện ở đó khó khăn thì biết làm sao ?
@@vanquynguyen8298 мы знаем как вы там живёте, да и мы не сладко живём)
@@65-Region не жалуйся,мы живём определенно лучше
@@65-Region за всех не говори кто хочет хорошо жить он добивается этого и не ноет
@@ПашкаПашкович-д3ч ну да. Расскажи как и чего ты добился?
Наверное, все нищие мечтают недоедать? Пацану из бедной семьи из умирающей деревни где нибудь в тайге, конечно, только захотеть и стоит, чтобы "всего добиться"
They AllWAYS have a helper who is learning the skills
Strong people and hard working
You can learn alot
They're dumb as a stump and spreading their stupidity.
Вот откуда берутся контрактные запчасти без пробега по РФ
такие запчасти только на украину поставляют
Я надеюсь это ж прикол был? Типа потроллить решили сообщество?
¿ Que garantía le darán al cliente por este trabajo?
Unicamente puede durar si lo guarda en una caja bien envuelto y engrasado. ¡ Vaya chapuza!
Nossa, esses caras são doidos.
Da o maior trabalho tirar o motor, desmontar,retificar, montar de novo e colocar no lugar pra fazer uma gambiarra dessas, eu aposto que não dura nada.
Eu achava que o Brasil era precário...
Kkkk, acho q é só pra fazer o vídeo. Íntegro ele já quebrou, imagina com esse remendo.
Sem falar que nem vai ficar desbalanceado, o motor vai tremer mais que um 3 cilindros 🤣🤣🤣
So it will make a good post for a be mail box.
это наше ближайшее будущие! уже законодательно разрешили использовать восстановленные запчасти....
Reminds me of the early nineteenth century
Hello ATO. That all looks like a carpenter fixing a table leg. Dowel pegs and all. This must be one of those scrap bin jobs where busted parts are “fixed” for the video. Sure hope Utube pays them well. On the other hand, that’s probably a crankshaft for a top fuel dragster. Maybe John Force Racing gets their cranks from ATO. Always wondered what those fender stickers stood for. Now we know.
Never drive farther than you want to walk. Just sayin.😊
Изначально это вал выработал себя на 1000% они его ещё ремонтируют, его место в металлоломе.
гараж 54 пусть сделает испытание,им один хрен нет чем занятся)))
Уже есть к жиговскому мотору добавили ещё два цилиндра
make video to prove that this crank is functional...
Na realidade deles rodou 6 meses está ótimo.
Nunca vi um serviços desse mas se rodar 6 meses tá bom demais ...
Nem deve ter ficado desbalanceado HaHa
That crank is good for another 100,000 km I'm sure
Somebody forgot to tell these boys....."You cant do that."
That's why they are so busy..substandard repairs.
That should last maybe a day or two. Operators in that part of the world routinely overload or otherwise operate their machinery well past reasonable parameters. Always.
Тут даже я "прикуел"!
Very good😍😍😍😍😍😍😍😍😍😍😍😍😍😍
Японский инженер застрелился от просмотренного видео.
Ни или деталь делают на постамент в музей....
Nothing amazing about it. This crankshaft is out of round, out of balance & the structural integrity has been compromised.
Klinger.....you screwed the pooch on this one...GUARANTEED comeback!!
Коленвал на болтах скрутили. Оригинально!😂
เปลี่ยนใหม่เถอะพ่อคุณ หักขนาดนี้ยังซ่อมใช้งานอยู่ รึ
Bad weight balance of the crankshaft will be the last problem here... :)
На эпоксидку быстрее , а можно просто тфу сделать ,! Контрактный коленвал !
Good job
Just use hot glue. That’s how they build all their free energy devices !!!
.. oh yeah, looks good, that will never break again .. lol
.. as long as its placed directly in the trash bin, and not dropped there.
Это наверное шуточное видио?😂 Такой коленвал обычно на переплавку отправляют. Не забудь зашпаклевать и подкрасить .
Шейку вала не закрыл от брызг от сварки,всю засрал , бесполезный труд все это . Гарантия пожизненная пока электроды не закончатся.
Will explode the first time it fires on 8, the crack is still there and the oil passage is blocked as well.
I like the way they just completely ignore the fact that they're welding the oil passage shut.
I suspect these guys have done this before.....ok would not happen in the west....but sometime we have to do what we have to do with what we have to hand.
Yes I would like to see how it stand up in action....but at least they try.....maybe some are ok for a while and they are happy with that.
If the could go to the dealership and get one off the shelf Im sure they would.
This is like going to a discount parts place. Get you through a bind. Harbour Freight
@@johnfairchild3421 Long as they are happy with the all is good.
I appreciate what your saying, but at the end of the day there somethings that just cannot be repaired to a level required by the forces that are going to be applied. It's a matter of physics not economics.
@@utube1818 Yes of course you quite correct.....but I wish I could find how long the job lasts till it fails.
خیلی جالب بود.👏👏👏👏
Nice comedies. 😊
Без синей изоленты ничего не получится
When you're bored and just want a reason to make a video... if you repair it they will watch.
Well, it passed the thumbs up test. I wouldn’t waste my time putting it back into the engine..
That will not hold, welding just the exterior of the crack does not fuse the center of the cracked part and will break again under load.
16:33 ..and it's ready for years of service....holding your potted plants. 🤣
ну что --ох----но???? все четко канал мас-заделан...надежно красиво--КРАСАВА!!!!
One good launch at 5k RPM and the engine will grenade 💥💣🤭
Tell me something there sparky, how does the oil gallery work now? Or is it so super strong now that oil isn't needed anymore?
Guaranteed till it breaks .
I am proud of this man and hard work he puts in. But I won’t drive that car. The first downshift the load on flywheel will take the wheel true the car like saw blade . No way
Wielding the cast crank on room temperature with stick rod damn
WTF kind of car would take a crank like that? 1936 Cadillac, maybe...
amazing
Muy buen trabajo de torneado y soldadura, pero eso no aguanta ni 2 vueltas en un motor.
Ничего удивительного не увидел , у нас в России до сих пор так делают многие. Камазисты и не такое могут делать. У нас это считается, низкокласифицированный и дешёвый ремонт . Это и правда не надолго . Единственный плюс, что человек не без дела сидит.
Ok thank you very good❤️❤️❤️❤️❤️❤️
Thanks💕💕💕
Интересно у них есть бог сварочного аппарата или электрода? 😂
Сколько ходят такие коленвалы?
Ходят они до магазина.
да это чисто для видосов,на камеру делают а потом выкинут
Это музейный экспонат.
Напомнило басню ,, Обезьяна и очки"
I don't see how this repair will last, Is that crank even indexed? But the bolts that they are using, are they at least grade 8? Hmmm entertaining though.
Сколько опилок в каналах для масла, потом задиры будут на вкладышах и он опять к ним же приедет но уже с другой причиной
Им пох....
Ещё денег заработают
Será que vai funcionar ?
Bardzooo dobra robota 🤣🤣🤣widać że profesjonaliści Wazzup mógł by się od nich uczyć fachu 😃
Żyją w takim kraju że muszą sobie jakoś radzić :)
W moim C 4011 po takiej naprawie już tyś mh zrobiłem 😄
Ooo, widziałeś 😂
I to są mechanicy naprawiają a nie wymieniacze jeb...e 😂😂😂
يجب وضع براغي من معدن خاص لا يتمدد بالحراره
Сразу видно что у них жизнь очень тежолая
Балансировка коленвала? Не, не слышал!
Alta precisión!!! Jajajaja
too difficult.you Can put scotch or superglue. its easier😄😄😄
Not likely will hold up under load.
Next time it fails (about 1 week) they're going to use JB Weld....
Mission engine self destruct mode 🤣🤣😝😝😝
Some things should not be repaired, like a cast iron crankshaft, ment it down and cast a new one.
Next time a break a leg, I will use there philosophy and put a plaster over the break.
Gowniana robota.