Good. This is what i like. Your first video about sim800L was greate too! - (long time ago), keep doing this sim800L its right path. :) thank you. You are greate!
I liked your video. Have two suggestions; you can not connect two antenna simultaneously on the same RF port, furthermore be cautious to handle Lipo Battery, specially in your case where there are naked pins on the Lipo connector which can easily short with each other and and cause fire / damage.
Hi, great video, can you make a video where you use the sim800l module with a microcontroller board that uses micropython to execute tasks, such as sending and receiving SMS? Thanks.
i am using sim800c module. when i send sms it is working fine when the sim used is of old idea sim or old bsnl sim. but when i changed the sim to new vodafone idea sim or new bsnl sim message is coming. how to solve this problem?
Sir my Bsnl sim is not working in SIM800L it's sending sms but received sms is stored in other sim internal memory and not able view it's content ,other sim cards working excellent but problem with Bsnl any settings or suggestions
Hello sir... My sim800l didn't work... I didn't put those resistor you put on Rx pin... But when i send AT command it returns OK but it didn't receiver neither a call nor a sms... I used a 4G aiterl sim card can you help me please??
Sir my in sim 800l that AT command is not working and I didn't receive any reply like ok and when I tried to make a project it is not working please help to solve this problem
how to get sim800l to outgoing calls status....? like busy / call connected / switched off / or / network not found error... please try to replay this message
i used sim 800 l gsm module. sms came and after some time . SMS has stopped. Please help me to solve this problem module is crashing after sending sms help me code
Hi Sharvan Sir, recently i bought a sim 800L and put an airtel sim with proper voltage to its plus and negative pin. But i didnt got the network sim which should blink every 3 sec. It only blink in one sec. However the at command it shows the sim number... What might be the problem.?? Pls help. I need ur e mail. And contact addres to send these faullty simm800l
Hello there . Thank you very much for your work. I have a request from you. "mySerial.println("ATD+ +9++++++++++;"); updateSeries(); delay (20000); " . Among these command information, if the called number is busy or rejects the call, it must end the call without waiting for 20 seconds. What kind of code should be written for that.
sir very beautifull voice , prounciation and delivery.thanks
Good. This is what i like. Your first video about sim800L was greate too! - (long time ago), keep doing this sim800L its right path. :) thank you. You are greate!
Great Job. Thanks very much.
Your presentation was organised, clear and very relevant.
All of your videos are very helpful and informative. Thanks for your effors!
I like this vedio very much .Allah bless you with prosperity and happiness respected sir ..
Nice explanation. Great job.
Thank you very much.
I liked your video. Have two suggestions; you can not connect two antenna simultaneously on the same RF port, furthermore be cautious to handle Lipo Battery, specially in your case where there are naked pins on the Lipo connector which can easily short with each other and and cause fire / damage.
Thanks Saravanan , very good job!!!!
Very very useful information. Thanks for sharing 🙏🙏
Excellent presentation!!
Thanks, Sir. I really appreciate you.
Very cool. Your giving me ideas.
Fantastic.
Do we have a video of similar working with sim900 module with audrino nano
nice video Saravanan AL!
Excellent work..
Nice detail. Thank you.
Helpful video. I liked it
@5:32 1K resistor should be connected to TX pin. Else it will not function as voltage divider. Otherwise good video. Thanks
I agree with you, I have used the 2k2 + 1k0 resistor as a voltage divider too.
Ss
Great jop , thank you ♥
Hi, great video, can you make a video where you use the sim800l module with a microcontroller board that uses micropython to execute tasks, such as sending and receiving SMS? Thanks.
I like your video. Please make a video that send sms without English language
great job, if this support 4G gprs,it's good.
Yes it does.But not LTE 4G
Great Video Sir! Could you please tell the rating of the Capacitor that you've used?
It's 100uf,25v capacitor!!
good day sir your tutorial is exceptional. But please how do I send sms in code without using terminal
Hi sir will it support 4g idea or vodofone Sim card.I needed it for my project.
Can I make two way communication with same module simultaneously?
Please make a practical vdo related to SNMP how its work ?
Sir Can you tell me the which antenna is best for Gsm module 800l i have lot of networking problem in my area
Hello, I wanted to ask
If we use the sim800i module, can we use Bluetooth headset?
How do you get the analog voice from a call over USB?
Respected sir plz make a video on phone call menu to route option choice or key .
R u available in Bangalore to get trained??
i am using sim800c module. when i send sms it is working fine when the sim used is of old idea sim or old bsnl sim. but when i changed the sim to new vodafone idea sim or new bsnl sim message is coming. how to solve this problem?
Can I receive call and dial without connecting speakers? Just for testing?
Is there any AT command for sending SMS to the SIM address book?
Which diode is used to 5v
Sir it supports 4g sim or not....
My device is in COM 7 but I don't open Putty this Serial COM7. It show (unable to open connection to COM7). Why? Please Answer 🙏
Hi Sarvanan, How to send multiple SMS in this at same time.?
Does it saport 4g sim
Sir
Can we programme uno with this sim module to a gsm gate controller???
Relay triggering only from authorised number s ..
yes, you can...
www.technoelectronics44.com/2020/11/gsm-sim800l.html
Do we require any plan for sim?
Hi sir what is the meaning if AT+CPIN=SIM WRONG or SIM busy??
1) SIM800L sim card and mobile sim card are same or not
2) how many recharge cost per month for SIM800L SIM
Sir my Bsnl sim is not working in SIM800L it's sending sms but received sms is stored in other sim internal memory and not able view it's content ,other sim cards working excellent but problem with Bsnl any settings or suggestions
Hello sir good morning
I need some more support in SIM 800L and SIM 800 C module
So how can I contact you ?
PLease what code to do u load into the arduino board
resitor of how much ohm?
Sir ,iam getting No DIAL TONE
What is mean, can you help me
Hi sir share top2013 universal program reader review..
Hello sir, I did exactly the same thing but when I write AT, and ENTER, doesnt happen anything, what can be the problem?
Led is blinking continuously is there any solution?
Hello sir... My sim800l didn't work... I didn't put those resistor you put on Rx pin... But when i send AT command it returns OK but it didn't receiver neither a call nor a sms... I used a 4G aiterl sim card can you help me please??
Sir can we send json data using http post and if yes plz if possible can you make a tutorial on it
anyone solved issue regarding ctrl+z part off sending message. i failed to finish message in both minicom and putty
Is vodafone sim works?
Can you help me. I need to make the SIM 800 l gsm module receive sms
sir please explane about A9G module sir
Sir my in sim 800l that AT command is not working and I didn't receive any reply like ok and when I tried to make a project it is not working please help to solve this problem
SAME HERE, Please sir mention your contact info
How much current require for gsm800l (using dc adapter)
3.7v
Hello brother, please help me, it does not ring for me, what is the solution?
how to get sim800l to outgoing calls status....? like busy / call connected / switched off / or / network not found error... please try to replay this message
i used sim 800 l gsm module. sms came and after some time . SMS has stopped. Please help me to solve this problem module is crashing after sending sms help me code
How do you send control z via a program?
Solved. However the receiving phone says content not supported.
Sir one dout what mean 107A in gsm different of C&A in gsm
Which is suitable for call
Like a say 1 for thi say 2 for that or press 1 , press 2
No signal for unregistred emai
is there any gsm module with voice over usb feature
Please do It Tamil video. Because less creater in Tamil. 🙏🙏🙏
HELLO SIR
I NEED GSM
why with ARDUINO, why all the ENGINEERS use ARDUINO?
ARDUINO can't use in a electronic top projects
Error bro
Hi
Sir i want u r mobile no pls sir
I want one controler 3 phase
Hi Sharvan Sir, recently i bought a sim 800L and put an airtel sim with proper voltage to its plus and negative pin. But i didnt got the network sim which should blink every 3 sec. It only blink in one sec. However the at command it shows the sim number...
What might be the problem.?? Pls help. I need ur e mail. And contact addres to send these faullty simm800l
Hello there . Thank you very much for your work. I have a request from you.
"mySerial.println("ATD+ +9++++++++++;");
updateSeries();
delay (20000); " . Among these command information, if the called number is busy or rejects the call, it must end the call without waiting for 20 seconds. What kind of code should be written for that.