Ezgo golf cart light kit installation - How to install complete light kit with turn signals 10LOL
Вставка
- Опубліковано 24 кві 2023
- In this video I show how to install an entire Ezgo Txt light kit on a 1994 model. This kit works on 1994-2013 TXT models.
Purchase the kit here!
10l0l.com/?sca_ref=3681234.GK...
Please subscribe for more videos like this!
I never knew i wanted an ez-go let alone the lighting kit, until today. Thank you haha
Proud that you wearing your PPEs Homeboy. Seeing the younger generation being safe when working on projects is awesome. keep safe
Easy install my cart had vertical rectangular holes in the rear fenders from old lights so I could not in stall the lights as instructed. but I did install the tail lights vertically by using the template for the left on the right and flipping it for the lift with the TOP label out (away from the center of the cart) then installed the light for the left on the right and the right on the left. worked out great.
This was an amazing video. You did a better job of explaining it than anyone else I’ve seen. Thank you.
That means a lot! Thanks for watching!
just a little tip. you want your sparks to fly at you so that it doesn't kick back when using the angle grinder
I normally try to avoid cutting with the left side but I didn’t have much room. Good advice though and thanks for watching!
Used all your videos to upgrade my cart. Thanks for all your help.
Thanks for sharing your install. Doing my install today.
Awesome video!!! Thanks
Very good video. Easy to follow. My hazzard light switch is stuck in the on osition so I'm about to replace the turn signal unit to fix this. My old unit has the switch by the turn signal lever. All the replacement units i have found the hazzard switch is on the dash separetly. Hope I'm able to switch it out.
As always spot on. I appreciate it.
Great video bro! Helped with my install 100% appreciate it!
Dude you saved me hours of my life Thank You !
Great video. It helped me install my 10 LOL
light kit.
That’s great to hear! Thanks for watching!
Great video bro. 🤜🏿🤛🏻
Thank you. I got one of these kits and found the instructions aren’t great so your video helped. When I cut my first front light opening I got it a bit high so it doesn’t look perfect. The templates are okay but they could be accompanied with clearer directions. It wasn’t easy but i I was able to run my wiring through the channels on the underneath of the drivers side - had to cut some clips from the comments but they’ll still be secure. I’ll finish mine up and hope for the best.
Finished it up and all works well!
Great video! About to do this kit to my 1997 ezgo txt 36v DCS. However im hoping to find a way to get the large connectors through the floor board without cutting a hole.
Could probably be figured out with some time spent on it for sure. Thanks for watching!
What size tires and wheels did you end up going with? It looks great dude!
I ended up buying these which I couldn’t pass up for the price. They look great on there!
www.surpluscenter.com/Wheels/Wheels-Tires/Pneumatic-Wheels/22x9-00-10-21x7-00-10-ATV-UTV-Aluminum-Wheel-Wanda-Tire-Set-of-4-1-5818.axd
Thanks for watching!
If you brake while turning, does the back light blink or is it constantly on?
If you signal left for example while braking, the left light will blink while the right light stays on steady
My 95 easy go has plastic around the front and rear. Do you just cut through it to put the light kit on?
Yes that’s what I had to do on mine
@@TimothysTractors Thank you brother that was a very good video appreciate it
I've purchased two of these and can't get either to work. I have a 2005 EZGO. What are the blue and red wires for? Instructions say lamp switch but there isn't one. You showed them but didn't address what they were for. 10LOL has no support or phone number to contact. I guess it's good when you get them for free. Very frustrated!
If I remember correctly the blue and red wires don’t connect to anything. I’ve installed so many of these kits and they all have the extra 2 wires which I don’t understand either. I think it is for a manual on/off switch for the lights but I could be wrong. If yours isn’t working possibly you have the 9 pin connector backwards? It only works one way but might go in both ways. Just make sure everything else is correct too - black and purple are horn, red and yellow are brake lights and black and red are negative and positive to the battery.
I to wanna know where red and blue hook to?