Please read before removing the PIR Sensor. Firstly this video is misleading. This board has auto switch-off feature after 15 to 30 seconds. With the PIR sensor if your light turns off after 15 to 30 seconds, even if you remove the PIR sensor it will turn off after 15 to 30 minutes. So don't remove the PIR sensor unless you are planning to put it back. :)
Yeah, I removed the PIR sensor and walla.... it DID NOT work! Well, it turned on... but then it automatically turned off after few seconds. So, after removing the PIR, you may have to bypass that sensor and connect something else, WHAT?
Hi Sameera, You are dam right.Tthose solar lights comes with a 555 Timer IC of 30 sec. After the light go on, it stays on FOR ONLY 30 SEC. I did this test and now I'm working on the Timer. You have to take the Timer out or bypass it. Many thanks for your remarks. 100 % TRUE. If you have any info how to remove or bypass the timer just reply. I want the Solar Wall Light to TURN ON when it's dark and TURN OFF at Sunrise. Regards from Curacao Island.
Do you know of a way to bypass that setup? I was reading into my solar lights that it has a built in photocell I believe to turn it on only at night but can't find it in the circuit itself..thanks in advance
I am also planning to do this but that would mean to add batteries and increase capacity so it could run the whole night since it would now be always on. How much max voltage can the board take? I hope you make a video.. great to find this video.
There is also a timer in the circuit. By Remove the motion sensor, the light will only come on for a few seconds and switch off. It won't come on again unless power button is switched off and on again.
Hi there. Ran into your video, very nice. I bought the exact same light and its light sensor is so sensitive that it's activated when it's not really dark. How should I fix this so that it's only on when it's very dark?
I have an almost identical simple one, but with 3 light panels. When switched on, there's 3 choices of brightness, high , low or dim. High and Low come on via the sensor (as it should),then it goes back to dim. My question is, WHY does the dim stay on, and not go out like the H & L after 30 seconds? I've not put it up anywhere, yet, not until I know if the dim is meant to stay ON all night, or not? Or will it go off when daylight comes? If it doesn't go off, that means I'll have to turn it on and off every day. lol
Hello sir,I already removed the sensor but it not working... meant when I push the button the light is on but on 20-30 second the light off..can u teach me how I want to adjust the solar lamp if night time the light will open automaticly and off when morning...tq
@@BennyReichert Thanks, I think if we disconnect/remove the PIR sensor from the circuit. I think this may work. You're also most welcome for any suggestion.
Do not do it.In the dark The light will continue to shut of after 15 seconds. The person who upload this film should explain how to change so in dark the light will remain on all night
@@hanas_340 I just jump wire one of sensor leg with battery + it will stay on in dark and off in Sun i just did today with my two LED I am not professional but I did it
I don't think so. The price you pay will get you without over voltage protection. The light I have is already blinking due to overcharging. When I measure voltage across legs from the solar terminals it is 5.3 volts, for poor 3.7 volts battery.
Great video, works for some models, but in other models you need to bypass the circuit. Its very easy, you need to weld a piece of cable between the vcc lead and ir lead where the pir sensor was. Hope this trick helps you all
Hello. Do you think you could make a video on how to deactivate the light sensor in solar panel lights? I've had these solar panel fairy lights for years, but I want the option to turn them on during the day as well. I have to cover up the solar panel to block light if I want them on during the day. Thx u!!!
We already removed the motion sensor but the light doesn't last long and we just press the on button to turn it on, we want to keep it on the whole night. How to achieve that?
I got the same results. It will only last for 15 seconds then turn off. You need to turn on the light then turn off to activate then only last for 15 secs.
Can you help? My same device the light don’t get off. If no motion the light will become dim but it will not off. I want to to go off so battery is saved. Motion sensor is working fine. Only light don’t become completely off. Can you help why? I can repair myself if you just teach me what to do or why is this problem?
Hello buddy,i removed swnsor but light stays only for 15 seconds and the off.,do we need to complete circuit,how to keep light on all night till battery runs out
@@JungKook-ij6dj o sensor PIR gera pulsos quando a sua área de detecção e invadida. por isso quando ele é retirado é necessário providenciar um gerador de pulso para que a lampada continue acessa.
You are dam right.Those solar lights comes with a 555 Timer IC of 30 sec. After the light go on, it stays on FOR ONLY 30 SEC. I did this test and now I'm working on the Timer. You have to take the Timer out or bypass it. Many thanks for your remarks. 100 % TRUE. If you have any info how to remove or bypass the timer just reply. I want the Solar Wall Light to TURN ON when it's dark and TURN OFF at Sunrise. Regards from Curacao Island.
@@trikotomotif3381 I think you can install rocker/push button switch just for the bulb to turn on and off rest of the circuit can be left to whatever is there no need to change anything.just incase in feature you want to reset to default.
@@solanki_tech this is good, but here u have to press that button every time you want to off or on, what if we use a transistor that makes it automatic. once the switch the circuit on, led will not glow until there is no light on the solar panel.
leave the circuit will just remove the led wire. and + of the battery will directly in the collector of the transistor and emitter be connected to led + . Now solar positive wire will be connected to the base. when the sun will be up the base will not allow the led to glow.this will do the work
@@ArielLeange I think this will give u some idea about what i was saying.its not exact but almost same approach .ua-cam.com/video/m0q0vcs8VVA/v-deo.html
I got the same results. It will only last for 15 seconds then turn off. You need to turn on the light then turn off to activate then only last for 15 secs.
Isn't it obvious that even if the sensor is removed the lights will stay on only for the period it was turned on in the dark and goes off again in the dark!!!! Most of (posters/repliers) you are missing that part which is the lamp shuts off after a period of time...it is not meant to stay on even if the sensor is removed. This feature is not the function of the PIR sensor it must be built into the circuit itself...why can't you all think🙄 I'm as dumb as you all in electronics 🥴
@@motto666 leave the circuit will just remove the led wire. and + of the battery will directly in the collector of the transistor and emitter be connected to led + . Now solar positive wire will be connected to the base. when the sun will be up the base will not allow the led to glow.
Bom dia Não funciona da maneira esperada, fiz esse procedimento e ao anoitecer ela acende sozinha porem uma vez só e após apagar não ascende mais exceto se formos manualmente no botão liga e desliga clicar lá, mas mesmo assim ela ascende fica acessa o tempo do timer e apaga não ascende mais.
Wtf. You have a button in the left of this sensor and use it to change the mode of this item. It has 3 modes, the 3rd keeps the light on permanently. So why shoud i remove the sensor?!
Si amigo pero te olvidaste de decir que si solo tiene dos funciones no va prender. 🤷 como ej luz por movimiento y luz tenue , si lo pasas a fijo te prende solo la tenue y no la de 100 %
Please read before removing the PIR Sensor. Firstly this video is misleading. This board has auto switch-off feature after 15 to 30 seconds. With the PIR sensor if your light turns off after 15 to 30 seconds, even if you remove the PIR sensor it will turn off after 15 to 30 minutes. So don't remove the PIR sensor unless you are planning to put it back. :)
Yeah, I removed the PIR sensor and walla.... it DID NOT work! Well, it turned on... but then it automatically turned off after few seconds. So, after removing the PIR, you may have to bypass that sensor and connect something else, WHAT?
Hi Sameera,
You are dam right.Tthose solar lights comes with a 555 Timer IC of 30 sec. After the light go on, it stays on FOR ONLY 30 SEC. I did this test and now I'm working on the Timer. You have to take the Timer out or bypass it.
Many thanks for your remarks. 100 % TRUE.
If you have any info how to remove or bypass the timer just reply.
I want the Solar Wall Light to TURN ON when it's dark and TURN OFF at Sunrise.
Regards from Curacao Island.
@@nelsmartis8324 can you make a video on this? I am early waiting
Another sout there is no heat sink provided for led so it will damage the light if runs continuous ly
Do you know of a way to bypass that setup? I was reading into my solar lights that it has a built in photocell I believe to turn it on only at night but can't find it in the circuit itself..thanks in advance
I am also planning to do this but that would mean to add batteries and increase capacity so it could run the whole night since it would now be always on. How much max voltage can the board take? I hope you make a video.. great to find this video.
A maximum of two batteries can be used,
because of the solar panel not enough
ua-cam.com/video/MMK-nwVQ51Y/v-deo.html
Solution for this
ua-cam.com/video/MMK-nwVQ51Y/v-deo.html
Turn on manually
tell me the marking of the microcircuit with 8 legs, thanks in advance!!!
There is also a timer in the circuit. By Remove the motion sensor, the light will only come on for a few seconds and switch off. It won't come on again unless power button is switched off and on again.
Yes its useless video i try it to remove the sensor not its not working
Me too
Yes fake video not workinh
Much easier method is to take the fucking control board out and burn it and hook up simply red black wire to battery done deal
@@michaelweber3369 is that working???
Hi there. Ran into your video, very nice. I bought the exact same light and its light sensor is so sensitive that it's activated when it's not really dark. How should I fix this so that it's only on when it's very dark?
I have an almost identical simple one, but with 3 light panels. When switched on, there's 3 choices of brightness, high , low or dim. High and Low come on via the sensor (as it should),then it goes back to dim. My question is, WHY does the dim stay on, and not go out like the H & L after 30 seconds? I've not put it up anywhere, yet, not until I know if the dim is meant to stay ON all night, or not? Or will it go off when daylight comes? If it doesn't go off, that means I'll have to turn it on and off every day. lol
Hello sir,I already removed the sensor but it not working... meant when I push the button the light is on but on 20-30 second the light off..can u teach me how I want to adjust the solar lamp if night time the light will open automaticly and off when morning...tq
That leds stoped automatically after 15 seconds. How its possible to continued lighting?
que dure mas tiepo gracias
Yes, it is possible only when the PIR motion sensor is disabled.
@@technosmithz9589 how you disable the pir so the led will turn on in dark and off in light ?
@@BennyReichert Thanks, I think if we disconnect/remove the PIR sensor from the circuit. I think this may work. You're also most welcome for any suggestion.
@@technosmithz9589 no even after removing sensor light turns of automatically after 5 mins
2:26 What is the IC chip model? The picture is too small to see clearly
I think it is a 555 Timer IC
As u have shown this instead of the senor if we want to connect a switch do we have to make any changes
Do not do it.In the dark The light will continue to shut of after 15 seconds. The person who upload this film should explain how to change so in dark the light will remain on all night
Could you explain more please. I should remove the sensor under the a light or in the dark??
Sir I ded my own way it's working
@@hanas_340 I cane tall u my method that work
@@pakistanzendabad3793 Please tell me.
@@hanas_340 I just jump wire one of sensor leg with battery + it will stay on in dark and off in Sun i just did today with my two LED I am not professional but I did it
Hey sir Does this light have battery protection for protecting the battery from over charge and discharge ?
I don't think so. The price you pay will get you without over voltage protection. The light I have is already blinking due to overcharging. When I measure voltage across legs from the solar terminals it is 5.3 volts, for poor 3.7 volts battery.
Cover half the solar panel up so it doesnt charge so much...
I tried to replace the battrie with a charger 5v, the sensor does not work, the led is always on, any help? Or this work only with battery?
Great video, works for some models, but in other models you need to bypass the circuit. Its very easy, you need to weld a piece of cable between the vcc lead and ir lead where the pir sensor was. Hope this trick helps you all
what type of cable?
@@andriesfritz5594 a piece of electric cable, 0.2 or 0.5 diameter works well
this method works for me,
Sorry what's vcc lead?
@@joseluisjimenez7228 voltaje de corriente continuna
can you help me.I want the Solar Wall Light to TURN ON when it's dark and TURN OFF at Sunrise. Thanks
Thanks bro very useful video....
By default it works in night. I have requirement make sensor work in day. Is it possible?
I also need to know how to make it work during the day time in day light
@@tonyman2340 Add a switch to the Solar Panel wire - turn off during the day for light - remember to turn back on for charging.
@@dnbliff thanks a million
ua-cam.com/video/MMK-nwVQ51Y/v-deo.html
Turn on manually
Very good sir.. new subscriber here.. i appreciate your video
Hello. Do you think you could make a video on how to deactivate the light sensor in solar panel lights? I've had these solar panel fairy lights for years, but I want the option to turn them on during the day as well. I have to cover up the solar panel to block light if I want them on during the day. Thx u!!!
We already removed the motion sensor but the light doesn't last long and we just press the on button to turn it on, we want to keep it on the whole night. How to achieve that?
I got the same results. It will only last for 15 seconds then turn off. You need to turn on the light then turn off to activate then only last for 15 secs.
Yes
@@raymonddulatas1851É preciso colocar um puso para simular o sensor pir
ua-cam.com/video/MMK-nwVQ51Y/v-deo.html
Solution for this
How about the timer? There's a time somethings a seconds when the light will off. How to disable the timer?
Can you help? My same device the light don’t get off. If no motion the light will become dim but it will not off. I want to to go off so battery is saved. Motion sensor is working fine. Only light don’t become completely off. Can you help why? I can repair myself if you just teach me what to do or why is this problem?
ua-cam.com/video/MMK-nwVQ51Y/v-deo.html
Operate manually
Hello buddy,i removed swnsor but light stays only for 15 seconds and the off.,do we need to complete circuit,how to keep light on all night till battery runs out
É preciso colocar um puso para simular o sensor pir
same thing happen here only 15 seconds then totally off. you have to re switch it to ON again.
@@JungKook-ij6dj o sensor PIR gera pulsos quando a sua área de detecção e invadida. por isso quando ele é retirado é necessário providenciar um gerador de pulso para que a lampada continue acessa.
ua-cam.com/video/MMK-nwVQ51Y/v-deo.html
Replace battery and fix to permanent
If someone gonna remove the PIR sensor, remember there's a timer in side the circuit. So we have to always switch on and off when remove the sensor 😂
Yes, I did it today, its now going off as per timer
Same here man..
Got any solution?
Need use resistor 10k
You are dam right.Those solar lights comes with a 555 Timer IC of 30 sec. After the light go on, it stays on FOR ONLY 30 SEC. I did this test and now I'm working on the Timer. You have to take the Timer out or bypass it.
Many thanks for your remarks. 100 % TRUE.
If you have any info how to remove or bypass the timer just reply.
I want the Solar Wall Light to TURN ON when it's dark and TURN OFF at Sunrise.
Regards from Curacao Island.
If we just remove pir as you shown ,will it work ,because we need to complete circuit,right
É preciso colocar um puso para simular o sensor pir
Reverse the pins of the pir (sensor), it works for me
ok
When am remove sensor the light is directed glows . On off switch not working
ua-cam.com/video/MMK-nwVQ51Y/v-deo.html
Solution for this
Yes it's working. But only for few minutes. Is there any way to continuous working?
Same to me 😢
Can you help me? Is there a way so that it will turn on manually without touching the upper part?
LED light directly should be connected to the battery and set the switch
@@powergen522 please have a tutorial pleaseee
@@powergen522 vedio tuturial plss
ua-cam.com/video/MMK-nwVQ51Y/v-deo.html
Turn on manually
Can i just cut it? I dont have a soldering tool
I dont have one either
How did you do i an also facing the same problem
ua-cam.com/video/MMK-nwVQ51Y/v-deo.html
Operate manually
you can put a strip of tape over it
Don't do it this is fake video ,chip has programs that will do auto switch off . Even when you remove the pr sensor
So, how to solution continued lighting in the night,? I must remove ic
@@trikotomotif3381 I think you can install rocker/push button switch just for the bulb to turn on and off rest of the circuit can be left to whatever is there no need to change anything.just incase in feature you want to reset to default.
ua-cam.com/video/MMK-nwVQ51Y/v-deo.html
Operate manually
@@solanki_tech this is good, but here u have to press that button every time you want to off or on, what if we use a transistor that makes it automatic. once the switch the circuit on, led will not glow until there is no light on the solar panel.
I need this solar light to lit in high intensity when it becomes dark until the battery will get empty.
leave the circuit will just remove the led wire. and + of the battery will directly in the collector of the transistor and emitter be connected to led + . Now solar positive wire will be connected to the base. when the sun will be up the base will not allow the led to glow.this will do the work
@@Abhinashkumarsingh your explanation is very confusing, can you detail this better???
@@ArielLeange I think this will give u some idea about what i was saying.its not exact but almost same approach .ua-cam.com/video/m0q0vcs8VVA/v-deo.html
@@Abhinashkumarsingh no one speaks that stupid language 🙄🤦🏼♂️🤣
Please give me any trick to make this light bright.
How can I increase its brightness.
I got the same results. It will only last for 15 seconds then turn off. You need to turn on the light then turn off to activate then only last for 15 secs.
I am also need
É preciso colocar um puso para simular o sensor pir
ua-cam.com/video/MMK-nwVQ51Y/v-deo.html
Operate manually
Isn't it obvious that even if the sensor is removed the lights will stay on only for the period it was turned on in the dark and goes off again in the dark!!!! Most of (posters/repliers) you are missing that part which is the lamp shuts off after a period of time...it is not meant to stay on even if the sensor is removed. This feature is not the function of the PIR sensor it must be built into the circuit itself...why can't you all think🙄 I'm as dumb as you all in electronics 🥴
can we replace the battery with Duracell Rechargeable AA 1300mAh once to get better backup
ua-cam.com/video/MMK-nwVQ51Y/v-deo.html
Solution to replace battery and fix to permanent
ua-cam.com/video/MMK-nwVQ51Y/v-deo.html
@@solanki_tech you are diverting by sending this link. How to do? Can you describe? If you can't so why are you misleading others
Gracias, lo necesitaba ,buen otra pregunta como hago para aumentar el tiempo de apagado ejp 10 minutos gracias desde colombia
Gracias
@@mi4deorosrenault475 Hola, pudiste hacer esto? ando buscando la forma de hacerlo pero no lo he logrado. Saludos desde Costa Rica
Buenas noches desde colombia ,si lo hise pero no dio resultado amigo
Lástima, gracias igualmente
Estaremos pendientes gracias
I remove PIR sensor but it ligt only 30 seconds , Pleace tell me how to continued lighting in the night , not only 30 seconds
Have you figured it out yet? I think you need to by pass the circuit board.
@@motto666 leave the circuit will just remove the led wire. and + of the battery will directly in the collector of the transistor and emitter be connected to led + . Now solar positive wire will be connected to the base. when the sun will be up the base will not allow the led to glow.
I also did the same removed the sensor but turns off after 4 to 5 seconds
Edit:- the battery has low power capacity use it on medium
Same to me..😢
This is not working out. If you remove the PIR sensor, it will light up only for 10 seconds.
Because Ic of timer base
Thats fixed mine, Thanks mate. All the best
Kalo d cabut kabelnya doang ngaruh ngga ya om?
Bruh, it would be much more simpler just by placing duct tape in front of sensor 😁
Haha but what during day? 😄
How to modify the time duration...
The one i got will do that any way. When its dark turn on 1 minute turn off then wave hand turn on for 30 seconds repeat.
What's Circuit Ic code?
Mas depois dos 30 segundo ela apaga e não acende mais!
That's OK but look at the charging as this unit over charges in bright sun!!
my solar panel got detached how can i fix it ?
Not remove pir sensor.if you want continues light remove pir sensor plastic cover.100%warking.
Bom dia Não funciona da maneira esperada, fiz esse procedimento e ao anoitecer ela acende sozinha porem uma vez só e após apagar não ascende mais exceto se formos manualmente no botão liga e desliga clicar lá, mas mesmo assim ela ascende fica acessa o tempo do timer e apaga não ascende mais.
Sir is led ko sidha solar se chala ke btao plz sir
paano magiging on/off lang switch niyan sir?
Thanks
Video test sa steady lights please not working mine still the lights automatic off.
ua-cam.com/video/MMK-nwVQ51Y/v-deo.html
Solution for this
Will the light remain on
ua-cam.com/video/MMK-nwVQ51Y/v-deo.html
Turn on manually
I want all night my solar working but still only 15 sec what shoud i do?
ua-cam.com/video/MMK-nwVQ51Y/v-deo.html
Solution
How to disable the timer ?
Pano po Alisin Ang sensor yung nka steady lang po sna Ang ilaw
मेरे पास भी एक ऐसी सोलर लाइट है क्या मैं उसका सेंसर निकाल दु तोक्या रात को लाइट कुछ समय बात बंद तो नहीं होगी
replace PlR with LDR make vdo
Not workig to me..😢
How to disable timer?
This is how to make stay just on when is dark or what
if the processor has an auto-off time, it goes off again
Battery backup kitna hai abb
Don't remove the sensor, better u should try to dance in front of the light, whenever u needs to switch that 🤪
I have tried but mine didnt work need help please
ua-cam.com/video/MMK-nwVQ51Y/v-deo.html
Solution for this
Not working because light will cut off by the timer, useless video
Ok gracias en espera,
Sir sensor nikalne ke baad light kab tak jalega
Mi lampara solo tiene la función de sensor si se lo quito siempre prenderá ?
No es suficiente solo con sacarlo ..hay que unir pistas en el circuito ...malo lo que haces no enseñas lo principal 👎🤷🏻
Cuales son?
Bakit yung sa akin wala ng PIR namamatay parin
sir,
i can't understand your words
Yeah..only work for 15sec.. How to permanently light on when dark??
ua-cam.com/video/MMK-nwVQ51Y/v-deo.html
Solution for this
@@solanki_tech yeah nice but how to install the battery??.. Can you upload the tutorial?
Hello after 30 sec it will go on low mood 😄😄 no solution
It can be turned into metal
👍👍👍
you can always spot a India hand ...lol
Regular chalegi kua
Not working
you can try another method
Amazing
Theres an easier way just put a piece of electical tape over the sensor
If you do that, it will turn off and not turn back on.
ua-cam.com/video/MMK-nwVQ51Y/v-deo.html
Operate manually
motian sensr hataa ne ke baad light nhi lagtihe
Wtf. You have a button in the left of this sensor and use it to change the mode of this item. It has 3 modes, the 3rd keeps the light on permanently.
So why shoud i remove the sensor?!
Where to find
Where is it??
You can see it is just near of the pir sensor.
Have you really checked all three modes of the switch.
@@technosmithz9589 yes. The 3rd one keeps the light on permanently while it is dark outside, just like he does in video
Comment section never reply
Doesn't stay on
Back song terrible bad.😢
Motion sensor not working
You must clean your nails, mate
yes this good point and i agree😌,
2021 yr i see my video and realised my work🙂, so last 1year every videos showing my nail cleaned🤗,
Nahi ho raha hai meri pcb alag hai
Si amigo pero te olvidaste de decir que si solo tiene dos funciones no va prender. 🤷 como ej luz por movimiento y luz tenue , si lo pasas a fijo te prende solo la tenue y no la de 100 %
La mía tiene únicamente la función de sensor y si se lo quito siempre prenderá ?
@@angellopez7003no, el circuito tiene temporizador le quites o no el sensor esta se volverá a apagar.
Don't do that
It's fake video
This is not a fake video maybe what you mean is misleading video...
Bat parang sensor parin...
this imposeble sensor deth
I laik
Isso e mentira
Ngawerr
Waste of time
Ic no