Відео

대단한 숙련공입니다. 멋지다.하루빨리 저런분들이 잘사는 세상이 와야지.수고하셨습니다.

Great work despite the critics. It's a real talent you have. At least you can have this truck back on the road and help the driver make a little more income. Well done 👍

Salute to this man's dedication and craftmanship.

Grazie dallo zyo Francesco

Algum brasileiro aqui tbm assistindo?

He’s the definition of mechanically inclined!

CONGRATS !

😂😂😂😂😂😂

как же хорошо, когда тепло... и все дела на улице делаются...

I doff off my hat to these people.😊

Lindo ❤

Такой "ремонт" только что бы доехать до дома . Эта деталь под такими нагрузками работать долго не будет .

Everything within spec +- 1meter

Best i've seen a long time. These workers we needed in germany.

Imagine some 20 something in the u.s. nowadays. Trying to figure that out. Three jaw chuck key in one hand ..cell phone in the other

Искусный мастер.😊

Lath machine is jurking So how can he makes aqirate measurement of axel

Good job

Excelente trabajo saludos desde República Dominicana

Amazing knowledge 😮

В станку варити неможна уграїш в коробці підшипники майстер шпичка😅😅😅😅😅😅😅😅😅😅😅😅😅😅😅😅 😅😅😅😅😅😅😅😅😅😅

Muito bom trabalho, parabéns.

A lot of work but money was made.

There must be a region in India where they speak the munchkin dialect.

he applies pre heat before turning but not before welding on axle steel? How very strange

ابداع❤❤❤❤❤❤

Absolutely brilliant guy he makes it look easy.that took a long time to finish.safety glasses are a must protect those good eyes.

Красавчики! Руки из нужного места! 🤘

там такое биение шеек, похоже видео чисто для ютуба.

Bravo! 👍 Inspirational engineering, don’t lose the technology, ever…😬🇬🇧

Халтура.

Test the crankshaft for any vibration before using it again👍

Que feo es no saber...bola de ignorantes lo único que saben es comprar nuevo.... por eso no tienen trabajo

Inventive. Using a three jaw chuck isn't precise. Four jaw dialed in much better. Tightening only one jaw leads to runout, as all three jaws have some play in them from the manufacturer. Using a cheater to tighten said chick is a definite no no. Heating will ruin any heat treatment of the splines and they will wear quickly. Not the preferred method, but will probably work in the short run - and maybe that was what the objective was?

ชอบใจโรงกลึงพี่บังจังทำได้ทุกอย่างเลย

Parabéns pelo belo trabalho ,sucesso a vcs

Yes he is a great machinist , but he ruined the temper of that steel and the life that repair won’t be long

V hav degrees n education n they r practical

I’m 74 and still doing these types of things on a smaller scale. Born and raised in the USA. No college; just a high school diploma.

BRAWO!!

I think the singly mist impressive thing here is that's he isnt using a dial indicator and still getting a true cut

Very skilled, probably lives in a hut.

That will be 2 dollars, thank you

That things gonna snap on the highway within a month and possibly kill people.. it's not that people in America can't do this... It's that we understand torque and lawsuits

Й

The worst thing is that the mechanic workshop is far from the lathe mechanic, and then you have to go by motorcycle!🤭

No thanks !

How do you like the runout on that rear facing main?

That's just beautiful

👍👌