Відео

Разрешите, поинтересоваться, а что за транзисторы?

Super

Do you know it's flight time??

Bro is real pilot❤❤❤

I want to learn

NICEEEE!!!!

👍 💯

0955 it appears that the meeting of the motor mount bracket and pylon is Very short-on solidity.

0955 a drone rotor is not a prop. a correctly spec'd E/EP prop is Quiet.! there is a LOT of vibration coming from the motor and prop.! if you don't address it adequately, you will probably experience servo glitching (crashing). the motor has a lot of cogging and that is a source of vibration. use smoother running motor if possible. in any case, the structure of the power pylon Needs to improved so that there is less resonance and more vibration damping. along with the thrust config mods.

0001 it is not clear whether the distance between the stabs and wing is excessive. it appears that that distance should be reduced by about one inch. the tail Should be made as light as is practical. to that end, the span of the horiz-stab should be equal to thirty percent of the wingspan. the mass of power/control components should be installed in a grouping that RESULTS in the c-m being located on the imaginary twenty-five percent of chord line. if the ideal location of cg is added (at thirty percent of chord) to the c-m illustration it can be seen that an 'oval-shaped' concentration of mass, should be located in a vertical zone between twenty and thirty percent of chord. that is where SERVOS rx and battery Should be installed. it should be understood that locating the prop relatively farther aft will result in a 'gentler' ideal thrust angle. and, the use of an ideal adjusted thrust angle will reduce the amount of vertical offset that is Needed.

0001 ideally, the thrust line should intersect the (correctly located) c-m. it is therefore recommended that the thrust line/angle be 'adjusted' accordingly. the existing vertically offset thrust line will result in unwanted excess nose-down moment, at all times. the affects of this excess moment will be most apparent during a hand launch or at other moments of 'hard' acceleration. this photo contains one significant labelling error. the added lines intersect at the point where the c-m Should be located. static.rcgroups.net/forums/attachments/2/9/6/3/9/7/a5988257-224-bixler%202%20motor%20angle%20correction.jpg

please give me connecting diagram

And can i use rp2040 instead of Arduino nano

The cheapest and best it could get thanks bro👍

Connection please

Nifty and thanks. I think that your center of gravity might be a little off. I wonder if your setup might fly or not?

How much mah battery are you using?

MOSFET kon sa h

really nice, can you share the part names and total weight in the description maybe ? I am looking to build a similar but based on ESP32 for cheaper Tx/Rx. Also how long does a typical battery lasts (like battery lifespan, not the flight time), I am concerned if this will blow up my costs to run the drone for long.

Finally you made it work! Awesome, Respect! 🥰

Vm❤❤❤❤

Full video ua-cam.com/video/3cUvAfuSKZY/v-deo.html

Note, BLUETOOTH RC CONTROLLER APP IS NOT AVAILABLE IN PLAY STORE , SO TYPE " BLUETTOTH RC CONTROLLER " IN Google , proceed accordingly, download it.

❤❤

Voar que é bom. Nada ..

hello brother , nice plane btw. I am also building the same one to start can we ping i need some help !

Great job 👏👏👏

code??😅😅 nice video though🤩

DIY RC transmitter video needed

how to power the receiver? 3.7V?❤❤

It won't fly😂

another crap video of RC Plane making, no flight video means it doesn't fly at all.

another crap RC plane making video , no flight video, complete wastage of time.

very poor design and as it also doesn't have a flight video its very clear its not going to fly.

not impressed as there is no flight video, many videos available for making RC planes, but the real achievements comes when it really flies in the air and with safe landing.

very poor construction and layout, needs improvement.

the part of the fuselage located above the main wing should be ELIMATED.

348 rudder goes on the LEFT stick.!

Kaishare.

Nice! Want to see a flight video! :)

Don’t need that horrible music will not watch that video

Bro ap mahnat bahut kar ta ho but editing ko acha karo you get million of views or fly kar ka nahi deka ya love form Balochistan ❤❤

Very nice

Show full tutorial

Buen Video por favor puede compartir codigos de arduino gracias

Perfeito. Gostaria de ver o voo ;)

Nice video bro. But put all the electronics in description .

Hay una vercion wifi que usa un esp8266, solo pone 2 mosfet en el esp8266 esp1. Usa espenow para un websoket con joistick en el navegador. No es nesesaria una app. Y se ahorra algo de peso, tambien es mas barato. No recuerdo el bombre del autor.

Can you please tell me the name of the application

But the real question should be: Does it fly? Of course not, it's probably too heavy to fly. Why make something that won't fly and call it an plane?