Відео

I just installed an RTX gauge cluster in my 71 big block Nova and I love it. Looks stock with the key off and looks digital with key on

Great job

About 40,000 misinformed people who watched this video including myself. The plug is not recessed a 1/8” on mine. It is recessed almost one full inch. Hopefully helps someone and don’t spend a bunch of money trying to fix something that isn’t broken.

Can the transmission temperature sensor be replaced in the unit.

So is there a way to use one of these transmissions behind a small block or even an ls style engine not a factory combo? Ive decided to stay with an automatic and i got a 6l80 2wd unit essentially for free. I know the controller is internal and relies on inputs from the pcm so is there a way to mimic the signals that thebtransmission expects to see or....?

My 07 has 13 pins

I got a 92 with a 6.0 ready to go i was thinking about running a 6l80 i got a local shop that builds them and said it can hold 1000hp Will i have any clearance issues with that transmission?

I replaced the passage sleeve twice and it’s still leaking from the connector. I have a new TECHM installed as well. At this point I’m tired of dropping the pan to address the sleeve. Plus the pins aren’t loose.

So im curious....does this mean a procharger aluminum intake with fuel rails would work on a c8 even though it was designed for a c6?

I have the following problem: I do not have a ground in any sensor and it is all new, when connecting a separate ground they do work but not with the cable grounds.

Yes sir I will fix transmission 6l80e

How are you sir 😊

I thought it was a 99 for the 300 mm torque converter on a 4L60E

🦾🙏🏽

What gauge of fusable link would you recommend between the 2 Red ringed wires that go to the Starter??

Was the throttle body resting on the alternator

can i use my bmw pedal with one of those tac modules? my bmw pedal is from a 2008 135i it uses a 6 pin ?

I'm looking for something like this for the obs fords

Can this TCM, even though its internal, still be reset by unplugging the battery for 30 mins? Great video btw. I was having trouble finding where the TCM was on my 2016 suburban

What are the torque specs for all these bolts when reassembling? Thanks! Good tutorial!

I had 2 tuners tune my gen V 6L80e and still have the code vss low correlation output any help on this would be very appreciated

I have a 2012 camaro SS 6.2 with a 2010 6L80 behind it. The TCM wont communicate with the ECM. Took it to the fifth shop today and all they did was to loose my tune. Can you delete the vin and install the correct vin into my TCM,

If u have issues with the E12 and it doesn't grab. Apparently some sockets are deeper than others. What i did was grind down the E12 i had a little and it worked. When i first put the E12 it would slip off like it was to big but the issue was that the the curved par of the socket was too deep and the star pattern wouldn't make enough contact. Great vid helped me get an idea of what to expect before taking it apart thanks 👍

Hello awesome video. I have a 2014 silverado 1500 lookn at doin this. Could you have you adapter plates or would that make things different How would this work with Stealth cam set up. Any suggestions.

Tell me why the @#$ it was placed inside the transmission when other years, it was not. What IDIOT at GMC thought this was a good idea?!

Question, do I still need to send the tcm in even if it is being swapped from another transmission?

So my G8 GT has the 6L80. By doing these steps I’ll be able to access my TCM?

Do they make a cluster for a jeep wrangler jk ???

Do they one close the jeep Jk

I just ran into this issue with an lh6 out of a 2005 trailblazer ext!

What's the smallest wheel/rim you can run. 19?

Looked up parts. Bare sub frame 400.00 rear diff 1100.00 and what ever the coil overs cost depending on brand. Probably be in it for 3500.00 total if you do it yourself I'm guessing.

Quick question will this c8 intake fit and l83 5.3 motor?

What’s your number

OMG thank you you answered my question I have a LQ4 24X reluctor wheel and I found a 05 GTO that has no motor in it so I’m trying to figure out if my motor will work I think it will not sure about the cam sensor if it’s on the front of the motor mines on the back

As a complete unit the TEHCM should be replaced too.

Didint help me a damn bit.

Where can we get the longer bolts

I just bought this harness from psi. Bought a 2003 suburban that had the fuse box and body harness catch fire and melt . I used this harness to drive the suburban to my dads property just had to remove vats with my buddy’s hp tuners . The harness was perfect just had to notch the maf connector .

What offset are you running. Just got mine in . Video coming soon

I have a question. I have a 01 vette. The engine block vin number and car vin match but my date casting makes NO sense. My casting date is K016.. so Nov 1st 06 or 96?? Lol makes no sense. C5’s ran 97-04. Plz help me understand lol

Make sure you don’t move the NSS…neutral safety switch. Truck will not start.

I replaced my tcm and the truck will not start, lost connection with tcm, pcm?

Is the speed sensor also in there?

Swapping a 2012 6l80e into a 2014 truck. I have hp tuners but can I get away with just swapping tcm from old trans?

So if i purchased a harness from PSI. I had to change my intake and the map sesnor will not integrate. Can i buy a pigtail to splice in from PSI. SUGGESTIONS?

thank you so much for share this video i really appreciate,I own 2007 gmc yukon still low miles,this video help me a lot to fix my issue code PO776-00 ,once again thannk you👍

I'll be driving up to see use guys in a few weeks when I get my block back from the machine shop

Me repararon la transmisión de una Suburban 2016 y sigues como trabadas se agarra y no quiere cambiar los cambió

If I’m running an older transmission in my 84 Chevy will the bim module still reed a VSS speed