![Victor New York](/img/default-banner.jpg)
- 13
- 128 243
Victor New York
Приєднався 5 лют 2007
Go New York
Part 7. Infiniti QX80 problems gone, injectors cleaner, rpm problem, po420 po430 catalytic problem
Part 7. Infiniti QX80 problems gone, injectors cleaner, rpm problem, po420 po430 catalytic convertors problem.
Remember - qx has one of the most reliable transmissions for that time, if you maintain it - should never have any problem. Change fluid and filter after 100k
Engine oil - full synthetic every 4k miles (not 5 and not 7k)
It has direct injection system- dirty oil will clog vvt valves.
If dirty oil - change every 2k (that's what I had, and not oil pretty clean even after 3k)
Clean injectors - a must!! 1 bottle /half tank for 3 time on a row at least.
Then every oil change.
Remember - qx has one of the most reliable transmissions for that time, if you maintain it - should never have any problem. Change fluid and filter after 100k
Engine oil - full synthetic every 4k miles (not 5 and not 7k)
It has direct injection system- dirty oil will clog vvt valves.
If dirty oil - change every 2k (that's what I had, and not oil pretty clean even after 3k)
Clean injectors - a must!! 1 bottle /half tank for 3 time on a row at least.
Then every oil change.
Переглядів: 112
Відео
Part 6 QX80 VVT solenoids and sensors re: transmission problem, jumping RPM, RPM surge, shifting...
Переглядів 5984 місяці тому
Part 6 QX80 VVT solenoids and sensors re: transmission problem, jumping RPM, RPM surge, shifting...
Part 5 Infiniti QX80 doesn't start. Battery or Starter ?
Переглядів 3,3 тис.5 місяців тому
Infiniti QX80 doesn't start. Battery or Starter ? Two common problems on Infiniti QX80
Part 4 Infiniti Qx80 Check engine PO420 PO430 catalytic converter problem Fixed
Переглядів 2,8 тис.5 місяців тому
PO430 Catalyst System Bank 2 PO420 Catalyst System Bank 1 update to my 1st video regarding jumping rpms problem.
Benz GL450 check engine code PO304 Cylinder 4 misfire fixed
Переглядів 4255 місяців тому
Mercedes Benz GL450 check engine code PO304 Also Mercedes Benz ML350, check engine code PO301, PO302, PO305, PO306, PO307, PO308 Cylinder 8 Misfire Detected
Mercedes 2007 GL450 Check engine code PO455
Переглядів 2938 місяців тому
You can do it yourself. No special tool requited. The P0455 diagnostic trouble code appears when there's a leak in the Evaporative Emission Control (EVAP) system, and the system can't maintain pressure.
Part 3 Infiniti QX80 QX56 throttle body, transmission problem, jumping RPM, RPM surge problem
Переглядів 7 тис.8 місяців тому
Video part 3 Check my first video if you didn't see it yet. check how to do it right way ua-cam.com/video/3B-a8WJtd8w/v-deo.htmlsi=rBhxedfl8wLF8Sph I don't know why I didn't do it early ! Air intake - VERY important ! Air flow sensor must be cleaned one a year! Air filter - high flow, washable. Before you spend money clean throttle body! if cost nothing! I had some kind of feeling that my car i...
Part 2 update. Infiniti qx80 transmission rpm surge fix.
Переглядів 6 тис.Рік тому
Part 2 update. Infiniti qx80 transmission rpm surge fix.
Infiniti QX80 transmission problem, jumping RPM, RPM surge, shifting problem
Переглядів 27 тис.Рік тому
2014 Infiniti QX80 150K miles. Made a video of how to solve the problem. Spent money and time. Im not an actor and English is not my native language, but hopefully understandable. Infiniti QX80 transmission problem, jumping RPM, RPM surge, shifting problem, groping gears...etc I dont have video with odometer/rpms after all repairs., but running great! Also note: if you have only one car (QX) yo...
BMW x5 roof problem. roof partially stuck.
Переглядів 80 тис.3 роки тому
x5 BMW Sunroof, x5 Moonroof, x5 Panoramic sunroof problems, Roof doesn't close, BMW x5 roof problem, x5 roof partially stuck
This is the worst decision they made,, a car without a gear handle in the middle 😅
U r a life saver sir thanks 🙏 for your help
Update 7.21.24 Made 2700 miles after last check engine light. Was using "seafom" injectors cleaner $6/bottle for half tank. Ate least 3..4 bottles needed
My 2018 QX80 randomly went into the no start situations over the past 2 yrs but usually would start when cooled down or boosted. Changing out the battery helped for a while but it seemed like the summer heat would kill it. Infinity replaced battery under warranty then I replaced it 3 times until I learned about the Nissan starter problems. The $90 Amazon starter replacement took me 3+ hours to swap out as it's located under the manifold but not a difficult job thanks to videos online and has never went into the no start situation again so problem solved. This should have been a Nissan recall because it's a major problem.
Thank you
Vraiment merci pour cette vidéo je viens de réglé mon problème la merci
Thank you very much. I have gone through the same except transmission valve. I’m based in UAE, I took my patrol y62 2016 se to many and all services were done in Nissan authorized, but they couldn’t figure it out and saying no codes, no problem. But as you experienced, I had the same issues rpm hesitation at lower speeds and intermittent. Perfectly fine at higher speed. I’m now with -major service done at authorized service-same issue persists, like you refered many forums, changed battery, changed Maf sensor, bit improved but still intermittent. Today one of the tech suggested for transmission check, you vedio and explanation is very helpful and tomorrow I’m going to change the fan clutch. Once again thank you very much, and this was very helpful to me…👍
@@ajaykumarna I didnt make video yet, but I suggest to clean fuil injectors ! Buy at outoze few bottles of seafom, use 1 bottle for half tank. Do it at leat 3 times ... at first it may act weid, but it work very well!! Try it now, and you may not need to check transmission! It even helped with cat convertos problem.
Thanks for the info👍
Thank you for this Victor. My 2015 QX80 is doing the same thing. I did the MAF sensor like you showed from the last video, but still had the RPM surges. I'll do the throttle body next.
Try to use seafom injectors cleaner few times bottle for half tank. Also make sure your engine oil good and changed around every 4k miles
Hello I have 2013 qx56 same rpm problem did you find the problem I’m from New Jersey
Yes, it fixed..runs like new. Not sure what exactly helped because did many different things and I believe there is few different problems...nothing costly. What milage? I would start with cleaning injextore with seafom $6/ bottle for half tank..use 3 times, oil change every 3..4k must, air flor sensor and throttle body, battery sensor and most costly fan clutch and Trans fluid ....
@@focusbvi trans I did new pan engine oil full synthetic just done I have 123k miles
great video
Thank you, Thank you, Thank you!
Thank you for this informative video! I'm sure the info will come in handy on my gen 2 Armada with 80k miles.
2017 Armada did the same thing, I replaced the battery and no more issues. Showed up the most on hot days and the starter acted funny as well until the battery was replaced.
Any update , I will cleaning my tomorrow and see,please let me know how you truck doing thanks
It runs good, recently used fuel system cleaning "techron" and injectors cleaning liqui molly... runs better...I still have problem with CATS, I have feeling that on this car engine oil should be changed every 3k miles. It has 181k miles, so pobably need new cats, new injectors...Im not sure if ever going to spend that much...but it runs well
@@focusbvi good for you, but you not need remplace fuel injectors, only cleaning will be enough, qx is a good car and nice looking vehicle
20 bottles of cata clean, o2 sensors just a hundred dollars shy of new cat.
new cats thousands
I got the P0420 code. Replaced the sensor, cleared code, 2 days later code came back. Same for you? I dont want to replace the cats.
The code came back after 2k miles. Also I was using Cataclen maybe 10 bottles before replaced sensors. Now im isung stuff to clean fuil system and liquimolly for injectors cleaning... so far 400 miles. What sensor you replaced ? Just one or both upstream and downstream?
Just the upstream. Which I replaced Sunday. I used the cataclean but just this morning and code came on this afternoon.
@@adamparris87 i replaced upstream first too and code cam back very soon, after replacing downstream I run 2k miles... hopefully this injwctors cleanr will help. What milage you have? I have 180k
I have 155K miles
O yeah the 7 speed (life time fluid) drain and fill every 25,000
Ours was a defective/weak/sticking starter motor solenoid. Acted up in May while on a 2,000mi. trip...then began working fine. Then acted up again in Nov...same-same. Battery was good/strong. Checked terminal #50 ( cranking ) wire to starter motor...good & strong. FINALLY got the solenoid to stick...CLUNK! Repl. starter motor ass'y. Still going strong after 2yrs. 2014 QX80, 97K mi.
fully depress the accelerator peda Wait 20 seconds and Fully release the accelerator pedal within 3 seconds after the MIL turns ON (((((((((( NOT RUN in wait 3 seconds in stop MIL ) and ON
Im having jumping RPM's. Transmission oil lines rotted out and lost all oil. Wife drove to work and couldn't drive no more. I Fixed lines and refilled with oil. Now, i have BCI MALFUNCTION and drives slow. Turn car off and drives like slipping between gears. My question is.. BCI MALFUNCTION doing this or tyranny??
2015 qx80
Engine light also on for 2yrs
Bci has nothing to do with transmission, but it can be related. What code you have? If its sleeping maybe wasnt changed right way, or low level
All oil leaked out when wife drove it halfway home. I drove it the rest and was slipping more and more until I got home. Mechanic fixed lines, fill it with oil and now(after 1 mnth) drives but slips almost every gear with rpm 3,000. Then BCI MALFUNCTION comes on limiting power
But transmission was totally empty
Hi there. I am having issues idle high, not running correctly. Thank you. Car repair keeps telling me nothing is wrong with my vehicle. I am in ROC. Any suggestions!?
Possibly problem with air flow sensor. Clean it fist
Guys Infiniti and Nissan are known for their torque converter. The torque converter will cause all these issues
Could be, but few people stated that replacing whole transmission or torque converter didnt fix the problem
Ty
Mine is making a constant whirring sound when I press start button but not cranking. Battery is new and charging plus Everything lights up. Starter still?
Mine was doing the same, recently replaced starter @ Infiniti dealership. Infiniti @ Orland Park, IL. has starter for $355 if you don’t want to purchase Autozone brand
Unfortunately After 2000...miles got po430 again. Did reset. Runs good. Will see when will get this code back again. Definitely dodnt want to replace cats.
QX runs beautifully, like never before, cleaning sensors took me 10 minutes. I wish I could do solenoids too. Cost nothing, I didnt even use any cleaners, just cleaned with microbiber cloth. Its just 2nd day of driving 50/50 highway/city. Will give update in few weeks.
im having same issue with my nissan partol at first i thought it might be Transmission Mount problem but it looks clean and no issues there according to the mechanic but thanks to your video now im more aware of the issue than before with my problem my car voltage is good same as you have in the video so i don't think that's my problem i changed engine oil and got new battery on already so maybe i need new transmission fluid or sensor issue either way thank you for the information this could save me alot of money for sure
I should watch ur video before i change the whole transmission gear and having same problems i will try all of ur fixes
Anyone know a part# for a 2016 qx80 third row passenger side seat motor? Please help. Thanks
Just call dealer parts department
@@focusbvi infiniti only sells the whole seat
Did you or didn’t replace the catalytic converters ? I also have p0420
Didn't replace it.
Thank you so much.. I was about to trade in my qx80 but now im going to try all your suggestions!
More than 2000 miles-still no codes, everything is ok
Replace altenator
why alternator ?
Do you have the part number for the O2 sensors
this is what I ordered: Downstream www.partsgeek.com/review-product/1Y4V33DCPS6 Upstream www.ebay.com/itm/204338016551
Thank you 🙏🏻 it’s so useful information
Українець чи Кацапчик ????
Victor thank you so much for this information. I just purchased a ‘15 QX80 with 163k miles ’As Is’. Having the same issues you pointed out but my engine light is now on. Going to check the codes and hopefully the repairs don’t result in a money pit.
Check the code, may people saying it torque converter...changing tranf fluid 2..3 times may solve it, but it will take time, will not see results righ away
@@focusbvi it is a bad car? I wanna buy a 2014 qx80
@@Young1blood496 no, its not bad car at all. I expected better interior quality and many things I don't like (have to make a video one day) but in general its good. If you buy one for 10k would be great, but not more than 15. I bought during COVID and overpaid a lot! Doing on time maintenance and its running better and better 180K miles
Where did u add the shudder fix to? The transmission fluid after it was a fresh change of fluid and filter ? I can’t the dipstick ? I don’t think it has a transmission dip stick … still looking thru owner manual. I bought the shudder fix trying to figure out where to add to??
I asked my mechanic to add it straight to transmission, no dipstick. But it didnt really make difference. After air flow sensor I would recommend to clean throttle body! Same as here ua-cam.com/video/3B-a8WJtd8w/v-deo.htmlsi=QRZoVH4lMO4jUqWH
Also check you enginge oil, how often it changed? When I bought it was low level and dirty, I was changing it 3..4k few times, now Im buying filers myself or requesting to put good one. Im thinking now...dirty oil may clogge VVT valve solenoids... and I think it also may cause this type of problem. (I may replace it later too).
@@focusbviit is a bad car?
You have to add shudder Fixx in a flush. Take it to dealer. You don’t just throw it in the old fluid
Your video is on point and SO HELPFUL!!! Can u repeat the name u mentioned the Cutter Cleaner? I couldn’t quite understand that word clearly??? Great troubleshooting and you have saved me a tremendous amount of troubleshooting time down .
CATACLEAN -I used it because few time had code po430. I also chenged upstream O2 sensor-didnt help, recently changed downstream O2 sensor- car started to run better, more torque/power, made 900miles, no codes.
I am dealing with this exact issue NOW!!! 2016 QX80 150000 miles. We cleaned the air flow cleaner and that helped for a minute like a week then it went back and the hesitation and lack of acceleration continues right in that exact RPM window mine is between 0-40
Hi, just wondering if you have fixed the issue?
There’s a red wire in the power box that keeps continuous power to the battery if cut. There’s a video on here about it. I cut that and it helped me a little. Still not totally fixed yet.
Fixed what?
I know you need to do relearn procedure after cleaning or disconnecting the throttle body on Nissan and Infiniti. I am not sure if it is the same for QX80. Here is good example video ua-cam.com/video/HIiaF0VaTlQ/v-deo.html
I think my doing all of that and if I'm not mistaken, I think my RPM jump up-and-down too. And I think I got multi misfire if I'm not mistaken. I think the code is P0300 something a multi misfire code.
Thanks for the video. My car is doing the exact same thing. I have a 2011 Q56I take it to the shop Thursday. I'm gonna tell them to do this cause. This other shop told me it could be the valve the valve body. And I'm wondering what should I do. Have them just fluffs the transmission fluid. Because I seem like my car. Always running kind of high like hard like in the idol. The r p m is like be jumping and it's supposed to be quieter than it is
Victor. I noticed that your steering while was discolored on video 1 but on video 3 it was like new. How did you do that?
Oh, you noticed that :) I layed with it different ways, have to make a video :) but ended up - bought that infiniti color paint on ebay called "luxury leather repair, automotive leatger dye" color IN40. Do few coats taping with sponge, each coat has to dry. If not smooth or see sone dust use 220 sandpaper slightly to clear dust. Tape wood, put plastic around and behind and spray clear coat of Minwax ..i had semi gloss 2 coats, you can use satin. Clear coat a must, otherwise it will get dirty in 1 week. It work great. Im planning to do it on the middle part of driver seat.
Please make video!@@focusbvi
Hi Victor, Thank you for your video. I have a 2006 ML350 that has the same code and I'm trying to find what the problem is. Did changing the valve fix the problem?
Replacement of rear valve fixed issue, not sure if ML has same. After you clear codes you have to follow instruction how to pass all units...fir example for O2 you have to keep 2k rpms during 2min....etc
@@focusbvi could you please link those instructions? I never heard about this
@@BROWNMAGIK1 starting 7:38min ua-cam.com/video/gLnhD4gP0kM/v-deo.htmlsi=0kUC3TtSmE6qCQue
@@focusbvi I ordered the valve and replaced it and now the car doesn’t have any codes and I can pass emissions! Thank you so much for the video and help
thanks for the videos i think the problem is dirty fluid the solenoid stuck changing the fluid multiple times can solve the problem it happened to my brother patrol
Transmission fluid changed twice together withvalve body, it didnt help... possibly needed long time til fresh fluid gets to tourk converter...anyway I can tell for sure its many issues together
Thank you. I’m having this issue with my 2016.
Thanks ..very kind