Відео

Don’t tighten it to tight.!. Just give it a snug tight.!.👍

Somebody touched the camera and didn’t clean the lense.😂

Ok people, for those who replaced the switch actuator and your air fryer is still not powering up here is most likely the problem, and even better the solution that will cost you NOTHING. For reference I own the PowerXL vortex air fryer. Great unit, has worked flawlessly for us over three years. I took this guys advice and bought the actuator switch on Am*zon. However before replacing it I tested the original and it clicked just like the new one. BEFORE you switch it out, learn how it operates. There will be a mount on which the actuator button sits. (Different models may vary but they kinda work the same way) Here is the best part: No need to buy a switch, and you don't have to remove the original switch. The secondary piece has a vertical striker that, when you insert your basket will push the button therefore powering up your unit. It's a little piece of plastic that will loosen over time. What you want to do is insert a VERY THIN piece of tape ( I used a small piece of aluminum foil ) between the vertical striker and the actuator button. I did this with great success! You may have to wait experiment with how thin or thick of a piece of tape in order for it to make better contact. TRY THIS BEFORE YOU BUY A NEW SWITCH. Having said that keep in mind results may vary. might as well add that this is merely a suggestion and I cannot be held responsible for any negative results. Good luck! P.S.- to the author, maybe pin this?

I wish that was my issue.

My air fryer stopped working on middle of chicken wings been done. Found this helpful vedios. Took screws off open it. The problem was just the nob on switch. When putting tray. It looks like it doesn't engage enough to start fryer up.Wiggle the nob couple time .plug it in to test and voila it worked. Finishing air frying the chicken wings not. Back in service. Thanks a lot. Made my day.

What do I do if it's not the switch?

My Power Airfryer XL is new, only 2 months old and it went out, is it possible that the switch went out in just 2 months. I can't use the normal screw driver too. Thanks for any reply.

Mostly the micro switch or Thermal fuse for the fan motor. 👍🇬🇧

What do you do when the air fryer stop blowing?

Were did you get the parts my son brought me two his boss gave him with the same problem 🤣

Tries this, saw that it was a problem common, but I will couldnt manage to get it to turn on. What would be the next problem?

Thanks so much for this video. It proved very helpful. Normally close (NC) option. I just want to comment that when looking for the part, apart from knowing the part number, the option should be for normally close. This is very important because if one buys the normally open option, it will not work for this appliance. I bought the normally open (NO) option and it worked in reverse. In other words, when you plug the air fryer, it energizes without the bucket, and when the bucket is engaged, the system goes off because it is normally open. So, the buyer should ensure he or she selects the normally close version.

Thank you for sharing 💐

I’m going to see if that’s what’s wrong with mine. Thanks 👍🏾

Thank you

I have a air fryers that was plugged and the wall socket blew and I reset the socket on the wall and plugged it back in and it would not work. Plugged in a power xl pro withe the rotisserie and it did the same thing. Plugged them into other sockets in kitchen and they still don't work. Help

My unit was working until about a week ago; the fan doesn’t circulate anymore. There is power to the unit, but the fan does not rotate anymore

I paid $300 for this 7 years ago. It's probably more now

If u look there is no connector for the 220 coming into the dryer vibration will eat into that cord give me a break sorry if l spoke my

<3

I still don't know what to do here.

Not worth watching.

Thanks for nothing ! Smh and that shit sound raggedy

Thank you for any and all help! Blessings to you sir

good video. Sounds like your roller wheels are worn out as well. Easy fix.

Go ahead and replace that tile...looks tired.

What was the point of this video!? You didn't show ANYTHING being done! "Here's before, and here's after." There ought to be law against such wastes of people's time!!!

How is this a how to, skipped all of the how to parts..

Make sure you open the stems all the way out before you loosen up the stem Makes it easier for the stem to come out Use thread sealant on the seats To make sure they don’t leak 😇😇😇

I'd like to say thanks a hell of alot for SHOWING HOW YOU TOOK IT OUT other words thanks for NOTHING

Thank you!!

Cracked headstock?...hell man, the title should be broken headstock

Totally skipped out on the only thing that was searched for. Big help. Smdh plus it sounds like you threw a short block in it after you turned it on.

FOOOOL

idiot

you had the big clamp far to high on the head stock it should of been where the truss rod cover is (remove the truss rod cover first though ) it would clamp better.

How long did it take?

I am amazed that you still remember that!!!! Thank you for a stroll down memory lane :)

Do you know anything about valve stem extenders?

How was this a how to do?

Agree - this is a tear jerker. Well done.

i replaced mines but my valve seat that i bought wasn't big enough any advice?

what size pipe wrench did you use?

Thank you. That was very helpful.

Got this letter saying I have won 15,000. But I have to pay Enclose a discounted fee ot only 9.00. You should not have to pay anything to win money. Only the Lotto than the money goes to hope education.

nice

Lol what is this

i am a single mother with 3 kids who was scammed through the internet and had to loose my whole fortune ,life became hard for i and my family with nothing left on us as feeding and personal welfare became a problem for me ,Not until i came in contact with the cyber crime agency that helped me in getting back all i lost even in double! if you have similar case just like me or you know someone that has been involved in any scam/fraud related issue do feel free to write me on traceyelswood@gmail.com so i can guide anyone on protocols i underwent.

Dumb.

This may sound like a funny question, but how did you know yours was made by Price-Pfister? I don't see any brand name on the parts.