Відео

3:14 "Paso importante antes del uso." I love his Spanish.

Exactly what I needed. Thank you!

The calculations are correct. But without measuring the real pressure, everything is just theory. I bought a manometer, measured and then calculated. And I convinced myself of the reality. In the technical book - 12 tons, real - 8 tons. You can see on my channel.

Bro make sure your using leather gloves and a respirator when using an airless

Did the spacer with the relief to just slide it in. Spacer just makes its way out after a couple days.

Thanks for showing the pinch weld cover removal. Quadratech omitted that. It's good to know that they will fit after the trim/protective steel is removed.

Replacing mine for the first time tomorrow, thanks for the video.

Thanks for taking the time and effort for this kind of very useful short video. Simple question, perfect answer.

Same model as mine. If you look closely at the bottom hinge, you will see it probably bent from door weight and gallon jugs. I fixed mine the same way you did but it bent further so I replaced the hinge with a 90 degree 1/4'" steel angle and cut it to fit and drilled necessary holes in angle piece. 5 years later never had recurring problem.

How long is the total time to remove and install? How much time should a handyman charge, that does this for a living?

is this a right door because it opens from the right ( on the inside) or a left side because.it slides from right to left im confused

Used your video to repair my fridge, thank you so much from vermont!

installing new sliding doors is always good, but I want to share with you my experience, I live in Orlando Florida, I contacted the Masterslide company with the problem of my sliding doors (if you ask, I will share the contacts) they replaced the rollers, installed a track cover and a new handle with a lock. Now my door is like new and I'm as happy as a child! And most importantly, I thought that I saved more than two thousand dollars! Just because repairs are cheaper!))) so think before ordering new ones. This is not advertising, this is my case.

I'm about to buy one of these for the west side of the house in a bedroom / sunroom. How are these in winter? Is the insulation good enough

This was the result of participation trophies 🏆 telling people they did a good job when, in reality, they didn't even come close to the finish line. 😅

Turn the music off and talk. I wanna hear whats going on not jays lame music

You go way to fast and you don't tell what your clicking on

how did it hold up. nice vid by the way 👍🏾

My house was built in 1967 is the ranch so the windows are up high I'm sure I can't even see out of my windows how do I fix that do I lower the windows remove the brick and bring the window down or replace it with new windows

Had the same issue with my freezer door. I cut a piece of toilet paper tube, folded it couple times and sticked it in the hinge and voila, no more rubbing. Probably not a permanent solution so I'll look into the nylon spacer too.

I probably would’ve measured 3 inches side to side and top and put a 5/4 around the outside you doing a good job just a lot of work

This is absolutely bollocks

Your fault

You turned into him look how much room you gave him from the apex

Learned valuable lesson that day. Pay attn to dad and grandpa.

Damn I have the same fridge and the same problem, I'm guessing it's common with these?

All the measurements are based on a horrizontal flat surface.

I use the graco the same machine that you are showing and someone told me to use Dawn to get the paint out of the sprayer and to clean around the machine with the hand moist towel and it does work and Dawn dish soap would also work if your bald-headed like me to take the paint off your head if you're not wearing a cap

Boxer isn't a racecar.....

Do you have a lever on the left side to lift the blades that has a lever with a spring? If so, how the hell do I move it to a higher setting? I can not get it even to the second notch.

So i get this right, you completely took the mower deck off of the tractor itself

How is this holding up ?

A drywall sander is a gamer changer! Makes sanding so much quicker!

What’s the material for the extension jams?

Brooo your lungs

Wear a mask man. Save your lungs while theyre healthy!

Great video! Thanks!

How did you put the belt on the front drive belt??

DIY'er here and trying to decide between this model and the Titan 1700. The Titan has a 2yr warranty, if that's a deciding factor. Also, which one has more replaceable parts? Currently Lowes has a discount on the Graco from $369 down to $315 compared with the Titan's regular price of $300. Anyone care to chime in? Thanks

Almost always need a bigger hammer lol

Considering a Z4 platform for Lemons out of Atlanta. How did this work out for you?

many thanks

I'm close to fitting 6 Piston 18Z Brembo calipers onto 350mm 5x4.5 rotors from a Mitsubishi Evo X. All going onto a 1999 2wd Ranger with 18x10 Porsche 911 Turbo wheels

finishing overlap can help with cutting round holes apparently

Hey, thanks for the vid. I'm about to do the same job. How did it do long term without the alignment?

I got all the parts, wanna come do mine😂😂😂

Hi, HI Can I ask you for help in my onshape project?

awesome and very helpful video just used it to start cutting on langmuir xr pro with primeweld cut 60. and worked great thanks.

32MM nut shd be 150 ft/lb torqued at least on GM cars.

Amazing, great job 2024 april03my 1st x seeing u ,looking 4ward 4 more ,iam about 2 do some home improvements, just preparing .my . Mind 2 getting started 😅 my favorite it's hard 2 pick it all looks great yeah the frame wall paper took it 2 a whole new level,Enjoy your space,Peace. N love 12:39 pm