- 61
- 532 703
Dave Prototype
Canada
Приєднався 3 лис 2013
Відео
Husqvarna 570 maintenance
Переглядів 771Рік тому
Sticking clutch, remove and clean Husqvarna 570 e-tech II Maintenance
Milling pine boards with STHIL 291
Переглядів 216Рік тому
Rough cutting 20" pine tree into slab boards Using STHIL 291MS chain saw Milling pine tree into boards
Kubota Backhoe quick connect system
Переглядів 5512 роки тому
DIY backhoe/excavator quick connect system Making the coupler and bucket ears
Trailer Maintenance and repairs
Переглядів 3362 роки тому
Repair a rotted out frame over the axle Cut out and replace severely rotted frame 4x8 Miska Trailer rotted out and could have caused an accident
Everlast Power arc 210 STL tig Review
Переглядів 3,1 тис.2 роки тому
Everlast power arc 210 STL tig set up and review Testing on mild steel and stainless steel No remote/foot-pedal control
2 Ton Tripod Safety Stands
Переглядів 4792 роки тому
We review 2 ton tripod safety stands (Big Red) They are to be used with a hoist for safety when removing heavy components or when the hoist is near capacity
GMC Sierra rear-end swap
Переглядів 3,8 тис.2 роки тому
We remove and inspect a blown up differential and rear-end Going to weld up the old rear-end into a spool for drift truck Save money DIY
HOLD on buddy shop accident
Переглядів 3012 роки тому
Here we have a shop accident hold on tight make sure your shop is clean so when you fall you dont get hurt
Blue Driver OBD2 Scan tool review
Переглядів 3272 роки тому
Blue Driver OBD2 Scan tool part 1 This tool is a diagnostic tool and reads codes on vehicles Save money on car repairs
Husqvarna 445e maintenance and 1 Year review
Переглядів 5 тис.2 роки тому
1 Year review and basic chainsaw maintenance how to sharpen the chain and file rakers Cutting some fallen trees and testing saw
Polaris Hammerhead GTS 150 run
Переглядів 5213 роки тому
Testing the Polaris Hammerhead GTS 150 Platinum on the flat track. This thing rips, supper fun and fast. Has five point harnesses and more
2001 GMC Smoke show
Переглядів 2933 роки тому
We test out our rear end after changing all fluids and replacing a axle seal. Only one way to do that...... light them up and burn them off... Smoke show time (aka burn outs)
2002 Honda XR100 engine rebuild part 1
Переглядів 1,4 тис.3 роки тому
Inspection of a Honda XR100 2002 motor getting ready to order parts and rebuild. Looking at service tolerances and general inspection.
2001 GMC Pickup truck full fluid service
Переглядів 2393 роки тому
2001 GMC Pickup truck full fluid service
Samsung dryer diagnostic repair and twist
Переглядів 6593 роки тому
Samsung dryer diagnostic repair and twist
Cool 👍
I just bought this saw as my first gas one..I really like it..lightweight and has enough power to not be too intimidating for a newbie..thanks for the video!
tutorial for installing engine sounds, boss
Is these parts are available in Flipkart order
Links to what metal gears you ordered, please
Please, put de links abouts elements from project, greatings from Colombia
It’s a long shot but would you be willing to weld a set of Mine if I mailed them to you? Thanks boss
Sure Im located in ontario canada
Well Done. I really like it.
Where did you get those metal gears from?
MLToys.com
Would you be able to tell where you got the parts to make the new shaft? I’m running into the same problem 🤦🏼♂️
Where to get these metal Gears 😢 please provide any links ❤
MLtoys.com
Husqvarna 575 ben do gia bao nhieu tien vay chu
Did you torque everything down to spec? Didn’t see you with one.
Yes, next time I will make sure to put that in the video
What?! No wrench sizes or any other info to get prepared?! 👎
Sorry we are getting better at giving more info, thanks for telling us. For sure in the next one we will mention it or put it in the comments.
Would you happen to have a drawing available for this build? Trying to do something similar.
Hi Dave, Great video. You stated the clutch cover is stuck on there (8:05) but then video skips ahead to clutch cover just being pulled off and mentioned using pliers and a little wiggling to get it free. I'm having a hard time getting cover off my 570 as well. Is it threaded on there? or, does it just slip on? How did you use pliers to get it free? Did you turn or just pull and wiggle?
How long did this set up last. Stage 1 or 2 cost a pretty penny.
I will say this I bought this little welder a week ago and there is something about the Arc and bead appearance on stick that I have never seen on Machines costing 10 times more. Haven't tig with it yet so no comment on that yet
Where did you get the torch with gas quick connect? Thanks.
Where did you order that gear? I’m trying to make my nieces 4wheeler go fast.
ML toys on line
great video, Thank you, My question is, I have never seen a steel lower control arm it looked and sounded cheap too me, Dont take that in a defensive matter, Usually they arealuminum cast. Is the steal part a cheaper alternative then the aluminum? I know alot of these car parts are china made and we are stuck with them and alot are cheaply made anymore, I was told that by alot of mechanics, Thank you
Thats the one they brought it probably was the cheaper one as they were on a budget
The use of these cheap parts by GM is why most people are now buying Japanese vehicles.
Yes parts are not very good these days
What a big job. Save a lot of money by doing it yourself.
Wow. Cuts through hardwood like butter!!!!
Thanks for watching Like, comment Subscribe
Do you always need two?
The trailer really needed repair.
Yes big fines it MTO pulled them over
Did it make it easyer to load other bucket into it?
How hard was it to clean and sharpen the saw?
This demonstration can save a lot of money. It’s a big job.
Doing regular maintenance keeps vehicles running efficiently. Thanks for posting.
The kids are going to enjoy riding.
More coils makes more heat also.
that is a nice dozer, they are so reliable
husqvarna makes nice chainsaws
That is an old machine, looks like its in good shape
those are big bolts for the main support
my Samsung took a craper too
Brakes are expensive , nice wrok
That is a full service all right, I need to get one done to my truck
Burn them off the rims,,, Tires must be cheap where do you get them?
Nice machine, looks fast
This saw is great, very comfortable to use...
These are good, I got one works mint.....
A lot of work but will save time in the long run.
This demonstration can save a lot of money. Thanks.😊
Great tips to keep you saw working efficiently.😊
Thanks for watching
That would make a nice fireplace mantel Great Video New subscriber
Thanks New videos coming up...
That is a good job diagnosing the clutch problem... Nice work..
Wow, this is a great video, lots of information, thank you for posting.
Thanks
Measure twice….cut once. That’s precision work!!!😊