Відео

6.0 or 5.3 Ls ?

What happened to the e82

does it work with auto trans?

Where is this car?

Ciao , questa modifica è stata fatta perché non riuscivi ad ottenere bassa pressione ? Ho lo stesso problema credo , di quanto hai fatto il foro sulla turbina ?

Thank you so much

where can the complete installation video be seen?

is there a wiring harness adapter, so the oem wiring plug doesn't have to be cut off, i have 2001 c5

Lesson learned. BUY NOTHING FROM CX RACING!!

If I understood I can use an S2000 airbag into an EP3 steering wheel and vice versa?

Where are you located?

Hey bro my 128i recently die looking to put a 5.3 LS Did u had to put a different transmission or I can use my stock one

Do u have to change transmission too ?

Did you just use an obd2 to obd1 jumper?

Did you just use an obd2 to obd1 jumper?

I will never understand why B series owners install there Turbo with the cold side on the passenger side of the car?? All top name turbo manifolds are made the other wat

Truly is a demon inside that ecu

Where can I get the swap mounts?

Did you give up on the E82?

You completely skipped the part i needed to see. Which was where and what gets soldered to install the demon. But good work showing that it works.

What happen

What I'm looming at is called a ram horn but all going to the right if looking from driver seat. I am NA header is for NA. I wouldn't call it a ram horn because of looks... but what ever. Any way... it's the 1320 b series 4 2 1. Any one know if it while fit tight on my 91 crx? I have the traction bar... I just don't want it sitting low from the oil pan.

Anything about power steering?

Thank you for the content tho

No lock tight bud 🤞🤞🤞

why didnt you just put the regulator you just built onto the waste gate and used pressure to move the rod instead of actually having to pull it

Nice job 👍💯

So The ecu is stock there?

the turbo you’re running is too big for that manifold setup, you’d either have to downsize the turbo or notch the block out and maybe even Dremel part of the turbo down as well to even come close to fitting.

I’m running this on a b20 vtec setup. I had a Garrett t25 on there and then got a China t28 after the t25 seized. It runs fine and looks good. I haven’t tried fitting the ac, but that’s coming up soon. Fits fine if you turn the turbo 180 degrees and jut cut your intercooler piping

I have the same manifold. I turned the turbo around and cut the intercooler piping

What bov are you running?

The cars that do this do not sound good sounds like a truck . It’s not that faster than a boosted but it’s stronger. You need to use nitrous for boost instead of turbos. Better off with a 2jzswap . But the reliability don’t let that fool you into getting an Ls swap trust me . If so you are gonna be spending a lot of money on nitro! Not street legal so first time a cop pulls you over and it’s not street legal you automatically loose your car just like when you ship over sea!

They sent me a fuel line that was too short.

I just had one come up for sale mint with a possible blown engine $4,000 and had to look up swaps. Awesome build!

What would happen if you installed the fuel line on the "return" or bottom bung and blocked off the sides of the fuel rail?

Is it ok to run it without thermostat?

I’ve a m54b30 in my e36 just ripped out all the ccv parts and valve along with the stock intake manifold , I was going to go down the m50b25 intake manifold with adapter kit but due to not being able to get my hands on one I’m thinking about getting an aluminium manifold from eBay , I’m none turbo so is it worth it ?

Still have that cooler ? Lol

please please help nEPTUn instantaneous data recording doreset not doing it and I do not know how-to turkiyedeyim.v nobody is helping me

u get a dyno tune?

Cobrartp is cheaper n just as good

Hows the turbo holding up?

Im sure its been said but try to say "uhhh" and "Umm" less. Apparently I say "uh" quite a bit too, so the wife says, other than that its a great set of vids.

Hate to be that guy but any update on 1 series you just stopped..

2 years later no forum update or UA-cam what happened?

The middle has to be grinded down for the ebay clamp to tighten down right.

Now swap the pump and injectors and crank it up to 20

Cool build! Should have went Coyote.

As I was wondering about doing this myself I found your video! Very helpful. Everything working out well with your build?