Відео

An animal or a ghost?

Great Tech and excellent content.Bravo. Jeff

407C R-32/125/134a (23.0/25.0/52.0)

The other company could have been doing nexstar sales tactics.

Oh I feel for the young tech who called for help not realizing the snarl of corporate red tape he just made. None of it is his fault, but he has to watch the train wreck.

Three phase motor can also switch directions if they mistakenly swapped two of the wires when rewiring it so if you reconnect a previously working motor and this happens when you start then look to see which two wires you swapped.

Jeff, I am puzzled by the high Super Heat and High Subcool numbers. High superheat low charge, High subcool over charge. Is it possible there is a restriction on this unit? Did this unit have fixed orifice or txv? If you would help me understand so I can avoid any errors in diagnosis I would appreciate it. Thank you for your videos.

Nice job of trying that too and you are doing great job out there and keep it up

it's been my experience with almost anything that no one wants to fix anything anymore, they just want to replace parts and most of the time not even the right ones . .

Wish you were in Toronto Canada

That’s so brain dead so the customer requested a visit and got upset when he showed up all because he had to sort some keys out for him. I would of told the guy fuck off 😂

You dont think an ecm motor would have been better. At least much cheaper

What symptoms were they seeing that required the service? Sputtering flames?

These old bell and gosit..pumps lasted a lifetime. If maintained keep them oiled ..and a spare set of springs couplers..on hand. Glad u kept same..as old one

Nice 👍🏼 😊job done ✅

Great job Jeff getting the heat on for the costumer thanks for the video

In a situation like that, I always tie the discharge side pipe with wire or crank up the hanger to raise it to get the old pump out and drop the new one in. You never want to slide it between the flanges for risk of tearing the gaskets. The other reason is you don’t want the pipe to drop when you remove the pump. You can do a lot of damage to the piping making a one hour change out into a four hour repipe job, which you wont get paid for.

😂😂 sitting here this morning drinking my coffee an listening to water drain out of the pump wishing this white stuff falling out of the sky was rain water 😂😂 I rarely rebuild repair a pump. It has to be an emergency overtime service call to do that R&R brand new pump and no headaches.

Nice work Jeff.

The mark of a good tech is stripping #6 wire with linemen’s or side cuts, been in the business for 26 years and never used wire strippers..

A vendor for these was set up at my Johnstone store. Went online and got one and it has been awesome!

Keep a ratchet strap or bottle jack with a 2x4 so you can lift/jack the pipe up to give you some room. Thanks for the vid!

I took one of those pumps out of my system and replaced with a Taco pump. Couldn't see spending the time rebuilding it......Taco pump is quieter and uses less electricity.

Interesting to see all the old systems you work on, that still work!

You couldn’t rebuild that pump? Just started watching. That’s what those pumps were good for, spring couplings and such easy rebuilding. Unless the motor is completely dead.

Great Video Jeff 👍🏼

🔥 🔥 🔥

Nice work man 😊

Wow I can see 1000’s of uses especially when checking out the heat tubes for cracks or holes.. ..

So the previous tech left and didn't check the operation? There is no way that contactor ever worked.

Hey Jeff, Merry Christmas to you and yours.

Great review Jeff.

Thanks jeff for the info on the scope have one of these very handy tool thanks for the video merry Christmas to you and your family

Need to know how to set nozzle and spark probes right adjustment

Como lo drenas

Sounds like the blower motor is not running fast enough to cool the heat exchanger?

Good Catch on that coil contactor Jeff! Cheers & Stay Well Man!

Incredibly informative and thorough video. I appreciate this very much. I am not a handy person by any means and even I feel confident attempting this after watching your video.

to many yellow flags with this customer

Sounds like a good customer.

We have a brand new house and installed a Rinnai tankless water heater. It heats the water initially but in 20-30 seconds, the water is cold. Any ideas?

And these boards are $2000!!

How long did it take to do that job?

I'd love to see a AFII to AFG swap.... thinking's about replacing the whole thing

You aren't the first tech I've heard hate on the AFII. As a homeowner doing maintenance and repairs, I'm sorta stuck with it for now. Can you explain why there is such a hate for this model?

What's the next step if the igniter is good. My gas valve will not open. Igniter gets power then flame light on board for a second then shuts down. Any ideas ?

Yikes 😳

I hate those meeses to piecesGood vid Jeff ... Thx

Another great video Jeff mice and all thanks again

Mice don’t bother me but … 🕷️ spiders?? I hate them…. Oh and snakes in craw spaces!! Nope not a snake lover😮 It tuff working in a craw Nice job a don’t you just love it when some one half ass a replacement part a just leave it dangling?? 🙄😡