Відео

Hey bud… I never made them In the end as I got next to no interest sadly. Looking back I think the real solution was the replacement of the clutch master cylinder, the bushes maybe helped. If you have this issue I’d 100% change that brake master cylinder… I could t stand that noise 😂 Crap job though, I’d get someone to do it for you if you cba. Thanks for the sub too 👍🏼🫡

@@yardspeed13 hey no worries ill grab one once I get paid and get the to fit it as I have no patience to do all that lol

@@skullz476 don’t blame you, don’t think I’d do that again if I’m honest.

Yup, they sure did.

Haha yeah, it was a bit... probably me being an idiot maybe?! I didn't realise, but after watching some other videos it's definitely not as straight forward as you'd like it to be. Maybe there are some better rails?! No clue :)

Thanks dude 🫡😎

Sorry mate I’ve been really slow at making this… I should have done it ages ago. I bet your vid will be great and the car is looking very nice I gotta say 👌🏼😊😎

Thanks bud… yeah, harder than I expected actually

Thank-you sir 🫡😊

Thanks mate… yeah there’s always something that doesn’t fit right. 😂😩

Hi mate, yeah it is a bit lower… but not much. Maybe about 3cm… it definitely feels lower especially compared to the passenger seat. Obviously each bucket seat will be different. The pole position is a nice seat, that’s what I wanted, but I’m too big for it

Recently did all this to my DC2. I got a Recaro SPG XL. I’m a 34” waist 6’2”. Pole positions are not suitable if you’re 6ft or over imo. The harness holes are really low on them.

Yeah mate, I’m a similar size (bit shorter) I found they flexed when I sat in it. The other seat I considered was a Sparco Evo XL but I decided against it because of too much branding wasn’t my taste. I’d bloody love a DC2… enjoy it man 😎

Cheers bud thanks for the sub too, appreciate it. Yeah I’ve been very lax on the uploads recently… but I have a video to upload, probs tomorrow. Just need to make a thumbnail 🫡😎

Sorry to hear that bud… how’s that happened, nightmare.

Era un mercado de Facebook. Originalmente era de Tegiwa en el Reino Unido. - Google translate. Hope it makes sense 👌🏼

you'll be fine mate, just go around twice to be sure you get all the air out. Good luck!

Hi mate, erm… I’m always a bit weary about advising people on fitment because of all the different variables. But since they clear my Yellow speed calipers I would assume that the same spec Enkies should fit over the Brembos. Hope that helps

@@yardspeed13 thanks mate 👍🏻

@@David-vy1sf If I were a betting man I’d say, you’ll be fine. Where are you located?

@@yardspeed13 Cheers 👍🏻 I'm near Blackpool

@@David-vy1sf bugger, not local then… I’d say try one of mine if you were

Paint roller next time 🤣

I just use the Tegiwa ones… they’re ok, not the best. Aluminium nuts always end up looking a bit crap if you’re lazy with cleaning, like me 😂

It’s a nightmare eh?! I’m sure it’ll be fine 👀😬

I hoped the same… but sadly I think it is inevitable 😬😩

Thanks bud, I’ll look on my Amazon account and get back to you…

I got 2 x 15M rolls. They were 5cm wide. I used 1 full roll. I think I had some left over

I need to do my front window seal too, I need to get it rust treated and painted before it gets too bad .😩 thanks for watching bud

Haha like it… I remember when we all used to have that option 🤪 Yeah I have to do a video on all the interior stuff I’ve done over the last few months. 🫡

haha noted... I'll get some for next time ;)

That scene always makes me laugh XD

Nice one, I’ll keep an eye on those too… the joy of old(ish) Hondas eh?! 😂🤪

Ahh, they keep us on our toes for sure 😂 the most paranoid iv ever been trying to chase and fix the boot leak 😅

I thought I was one of the lucky ones… turns out, I wasn’t. It’s not a pretty job but it works so far 👌🏼

Thanks bud… it seems to be holding pretty good it’s been done for like 3 weeks now, no leaks

Correct I haven’t made any content on it yet, I have another video that I haven’t finished ( I have been a bit lazy with editing) I didn’t install the cage but I wasn’t overly happy with the guys that did it for a few reasons. I got the cage done after i installed the bucket seat so I could have proper harnesses 👌🏼 I will try to finish that video soon Thanks for watching mate 🫡👍🏼

Mine aren’t that water tight tbh I think most of it gets through or when I drive off it just flies out…

Thanks for replying, mate. I thought I might have to unscrew them every so often to empty them and screw them back in

@@meetthewalkers1383 No worries bud, the rain guards are nearly as badly fitted as the bonnet 😂 if you saw underneath where they screw to the bonnet you’d know what I mean. Once you get used to the gaps being off most people don’t notice and normally say the bonnet looks sick. Piece of advice if you want it… make sure you protect it frequently with some kind of sealant of your choice, mine is lacquer peeling already at the front 😩😭

Thanks for the advice m8 I put the infinity wax synergy 2 year ceramic coating on it. Hopefully, this helps, or would u recommend something else ?

@@meetthewalkers1383 I’m not into detailing at all bud… so I’m the worst person to ask. My cars always dirty 🤣😩🤪

Mate I totally agree with you… I got mine 2nd hand so I gave it the benefit of the doubt, but yeah the fitment is crap. I imagine it’s the luck of the draw with the carbon moulding?!

Hey man, sorry I didn’t actually change the pulley, just the belt so I didn’t remove any bolts or have to torque them up afterwards. Is it the main pulley bolt spec you want or the bolts for the bracket that holds it to the engine? Or both?

No, but they stop my sweaty hands slipping on the steering wheel.

As long as you don’t remove the pipe then you’re good. You won’t have to bleed anything. It’s a real pain working under the dash… good luck mate, hope it’s fixed soon 👍🏼

You’re welcome… hope you can fix it soon. It’s either the clutch master cylinder or the bushes or both. Good luck with the fix and thanks for watching and leaving a comment 🫡😀

I have no idea… I’ve not exactly had it in a wind tunnel. Very difficult to measure… I just fitted it because I like the look of it

Thank-you mate I really appreciate that. Which BBK are you going for? If it’s the YellowSpeed like mine I was really disappointed with pads they supplied, especially on track. Hopefully you get to enjoy yours soon. Thanks again for the sub 🙌🏼🫡

@@yardspeed13 I've got brand new Renault Clio 3 RS Brembo calipers and going with EBC TurboGroove discs and EBC BlueStuff pads. I've been tracking mine with EBC brakes before as well and I have a good experience, so looking forward to this set as well :D I have just uploaded an unboxing of vid of mine a few days ago, can't wait to have it on the car :D

Thanks mate… she ain’t perfect i promise ya that 🤪

Hey mate, erm… sounds daft but have you checked both front and back? Is it from one side or both? It’s really hard to guess without having seen or heard it in person. Brake lines won’t/should t cause any noise. What are your dust shields like? Also does it only happen when you brake or all the time?

Thanks Daz I try my best to make it at least somewhat useful 🤪😂 I’ll get to a meet one day to have a look at your smashing motor 🫡 Always bloody busy though eh?!

I@@yardspeed13 I know mate, we have to keep busy to pay for overpriced mods🤣. Yeah!! be great to see you bud, maybe when the global warming summer arrives 😎🤣

It's annoying ay? You'd think they would have worked it out by now :) Thanks for watching and leaving a comment mate.

cheers man...

Funny you should mention that… I was going to wait and not install the rear bar. My beam isn’t that bad, but certainly not perfect, it does need replacing at some point. When I do the beam I’ll get all the brackets powder coated. That’s for watching mate and leaving a comment 😃

Funny you should mention that… I was going to wait and not install the rear bar. My beam isn’t that bad, but certainly not perfect, it does need replacing at some point. When I do the beam I’ll get all the brackets powder coated. That’s for watching mate and leaving a comment 😃

Funny you should mention that… I was going to wait and not install the rear bar. My beam isn’t that bad, but certainly not perfect, it does need replacing at some point. When I do the beam I’ll get all the brackets powder coated. That’s for watching mate and leaving a comment 😃

No damages to the paint of the car after using the grinder so close to it with no protection on it ?i was screaming "nooooooooooo the paint !" at the end of the video@@yardspeed13

Glad I helps mate… deffo buy some longer M8 bolts 🤙🏼

What were people saying? Man, big love thanks for the kind comments 🙌🏼😀 shame I didn’t get all the video I wanted but hey, we live, we learn. 🤪

@@yardspeed13 I edited it lol. People were asking me how to install it and stuff and I was like ohh... I didn't do it hahaha. Credit where credit is due my dude 👌🏾