Відео

Hey! Your video worked! I had the same problem. Fixed now. Thank you for your video!!

I can't even get arc stability with a 3/32 does fine for about 3-4 seconds. maybe the duty cycle is rated too low. does great with mig though.

Where can I buy this in Africa?

Thank you so much very helpful perfect explanation

Will .030 work on that .035 wheel?

THANK YOU SO MUCH!!

So glad I found this 😂. Saved me a lot of frustration. Thank you !

For what you’re doing, you don’t need this gun.

Is their any similar stuff that can help to clean the hardness of condenser tube inside of chiller units

First video I saw about this issue. i was going nuts trying to figure it out. Thanks Man!!!

Have you ever taken the temperature of the water after changing the ring to the hottest setting?

The M&P Shield .40 is actually ON the roster, as it is the subcompact model with limited magazine capacity (8 & 7 rd) and can be legally purchased. I lived in Vallejo, CA and was able to purchase this model at a gun show in Solano County in 2015. The FULL S&W M&P .40 that is NOT on the roster, cannot be purchased legally in CA.

Thank you!

Black Ops helicopter coming for you, prepper. 8:09

Is it suitable for tig ?

Thanks for the fix! It was driving me crazy!

They must’ve heard you because the kit I ordered came in today and it has them. It wasn’t even in the description of the order. It’s like they said “oof” and threw them in there on the rest of their kits.

Would that be ok to use with copper olives?

Good job!

Where did you get all the other black out parts

thank you for shower the brass part prying off, needed it.

Thank you! You are a gentleman and scholar sir 💯

This is not a problem unique to Readylift. Any lift without caster correction may result in bump steer or death wobble. Solid front axle coil spring caster adjustment is accomplished with a bushing that interfaces with the upper ball joint stem. Shim is not really a correct term for this part because it is actually an eccentric bushing but the marketing people call it a shim. Older vehicles with leaf springs in the front used an actual flat wedge shaped shim between the spring stack and the axle flat to roll the axle rearward. These bushings replace the factory bushing and come in fixed or variable degree increments. Double wishbone caster adjustment (F-150, Toyota etc.) beyond factory adjustment limit is achieved by replacing the upper control arms. If you take your F250 in for an alignment after you install your lift and they don't change the caster shim then they may not know what they are doing.

Thank you!!!!

What size fuel tank do you have?I have a 2018 6.7 and I only get 300miles on the range with a full tank. 😣

Thank you bro!!!!

Thanks bro

Can you show how to do it without the pedal?

We also used electric motor pod clamps that use air suction, they work perfectly, no need to manually adjust the height of the two edges, the air pods flush them up perfectly, but the kit is expensive but works 😎

We use a router with 1/2” corian blocks on each side of a double fluted 1/2” straight bit, about 1” gap outside of the router bit, these blocks are glued to the router base, the bit is set back 1/32” shallow from the face of the blocks, this allows the adhesive overflow to be shaved down, this saves from chiseling it and possibly putting unwanted chips into the face side of the SS, makes for much less sanding too, just something that is efficient for our shop, good videos however

Thanks very useful

Worked, thanks!

Jimbo makes Mexican food like a 55-year-old Mexican lady.

Your dog is freakin' awesome!

Good work bruv. Thanks for your help!

Thank you

Its massive compared to a pneumatic... but I haven't found a spot yet where it wouldn't fit, when my Teco (or just a hammer) wouldn't.

Thank you! This was driving me nuts

Thanks my man mine was doing the same thing did what you did fixed it thanks man

I thought the factory already ran wires underneath for running boards

So my label is all worn on my innerds. Whats it run 7018 like?

How are these power steps holding up? Do you deal with winter weather conditions? If so, do they work through snow and ice?

Nice video, I have the same truck 8”lift with 38s as I’m getting older it’s getting harder to get in and out! Are they lower than the one you had on? I wish they had one in chrome 😊

Very cheaply made. Broke first time using it

How do you keep from loosing your drill

Thank you the dealership wanted to charge me to fix this problem

Thank you!!

I have installed a 2” rough country leveling kit on 3 trucks all have been ford f250’s 2020 and up. I have never had any issues at all. As long as you already have a roughly 2” difference from the back to the front. It’s been 4 years and not one problem or malfunction

Your thoughts on expandable Pex B (Zurn) better resistance to Chlorinated water??

Over kill