Відео

Do you have a link for the Amazon connector lead?

Hi I got the YesWelder MP200 for my husband and the spool gun upgrade because he want to do alluminium but he does not speak english so would it be possible to have a plan of how to connect the wire to help him.

I dimmed my eyes, watching🫥

I have access to a large wood lathe, would it be possible on there also? Or does it have to be a metal lathe for some reason?

Im looking at doing the same mod. If i wanted to do it more budget friendly are there other spool gun options. Yeswelders is $190

Put more video please of these mini welding machine (more test) over head, vertical up/down, check welding penetration, test each parameter!!

No need for all of these budget welders when you have the best that money can get with the primeweld tig 225x to your left. Add the maxcool 3000 watercooler to it and you can weld for hours on end..

Hello, we want to invite you to help us test our machine, could you please give us a chance ❤ thank you

Did you ever get it dialed in? What are your settings?

Damn the most dangerous video to watch welders remember your audience is not wearing a shield!!! Just show end result damn Im seeing spots............

What voltage did you run on your tests? Did you do 110 or 220?

Thank you for your honest feedback. As a professional welder, your input is invaluable to Arccaptain. We will carefully consider your suggestions and continuously improve our machines. Thank you.

Much nicer than the one i got from Harbor Freight, that's for sure!

How has the mod been holding up? I'm looking to do the same thing.

That much is a dc machine only

Want to try Arccaptain Machine?

The 250 pro is now $400 on Amazon with the $100 coupon they offer. Im stuck wondering if it's worth it to add a 220 outlet.

Hello. How about a 2 year update on the Pro 250. Is it still working the same, would you purchase again?

How do I get in direct contact with you to obtain directions and/or a diagram to make this upgrade modification? We are new to welding, so we don’t know the inner workings well enough to know what to tap into. Not sure how to share contact info without it being public to all. Thanks!

could you do a 1 year later review?

Anyway to get a little more information? I assume you're taking the power from the board that powers the wire feed motor and using that as the primary power to the DPDT switch? Then one side of the switch is going back to the wire feed motor and the other side is going to the spool gun?

So at 18 volts this probably wasn’t spray transfer but still looks good

Any conversion for the TIG

어디회사입니다

Hi, I am trying to figure out if the 250 is really more powerful than the 205. YesWelder is known for rating the output much higher then actual output. My 250 pro does not seem any hotter then any other 200 amp Chinese machine and the auto settings are waaay too cold.

Does the factory 2-pin connector still function after this mod, or do you have to use the new connection when using the standard MIG torch?

I didn't want to modify my welder but I just might ... I also want to take a wire out to quickly switch polarity for the gun instead of the screws inside. Also any chance you have / can make a diagram?

Update.. after 2 weeks and an email a day the only help I got was a picture of a finger pointing at a connector to check... When I asked them what to check with a meter or am I just verifying it was plugged in they replied "we have reviewed the video you sent us again and it's broken and can't be repaired, sorry.". Basically they just want to string you along until you get tired and give up. So now I have a paperweight.

Well I'll Be 🤩

Thanks for sharing

Great help in my decision thanks for sharing and hope you've replaced that table that was scarry 😬

How can I get details on where you tapped into? Is it just the spool drive motor?

Need to have ac/dc tig with pedal and spool gun then it would be the ultimate diy machine.

what aluminum wire do you use? 5356 or 4043? I'm asking because the soot is so low for MIG, even with high flow of argon. People say 5356 is generally sooty. And it looks like you pull your welds instead of push. The results are fantastic!

Thanks for this - I tried this mod on mine and works flawlessly- just make sure to pay attention to where you drill the hole - TIP - cut the ON/OFF toggle label with tin snips and use that as a template for marking the 12mm hole - one draw back I noticed is that you cannot directly set the spool speed on the mp200 instead you have to change all the settings and gas to like cr25 to approximate

This video is almost two years old, so Yeswelder may have resolved/changed a couple items for the 250 Pro. Specifically, they state on their website that the torch and stick holder are 10’ now.

Can you do a more detailed video. My mp200 should be here end of March and this looks like something I want to do

You really should be wearing a respirator or have an sucker tube. You don't want that smoke in your lungs. I have been considering this welder and you've helped a lot.

Bring the feed down to like 10, volts like 29, and get yourself some 90/10 argon/CO2 for some good spray transfer

why can't you run aluminum from the factory spool?

man, that bad boy is packed! what is your interpretation on the stick function, on the 60xx rods, does the ground go to positive?

Do you have part numbers to parts you used?

Thanks for your contribution. Were you still using C25 gas?

NICE!!! 👍

Your welding 1\4 aluminum can it weld 1\8 or 1\6 aluminum like I do with my primeweld Tig 225x which is only $300 more than the yes welder 250 pro????

I’m looking for a welder, at work we have the Miller 350, goes up to like 28v and 650ipm wire speed. I don’t need anything like that but the option of being able to run up to 25.5 volts and 525 wire speed (my favorite setting other then spray) is something that I really want.. so here I am watching reviews lol trying to find my answer

What’s the max wire speed ?

What roller are you talking about you are waiting for?

You need a SS brush.

Hello friend, good, I have a question I hope you can get me out of doubt, have you already tried the machine in the Tig process ..? If so, how are you soldering in that process ..? Thanks in advance..