Відео

So for painting it sounds like a one stage is better, is that correct?

Hello! Please help me with the electrical connections for 220 V to an electric motor lesson 190011-53.Now it is connected L1 T3 T5 T1) and L2 (T4 T8 T2) and when i power it up it short and the fuse blows i think this is the 110v connection i need the 220v connections.On his wiring diagram it shows 110V LINE (T1 T3 T8) for 220V LINE (T1) TAPE (T2 T3 T8) LINE (T4 T5) But because I don't work with electric motors, I don't understand the scheme, it confuses me at 220 volts. Thanks!

Very good video and SO informative. Exactly what I was looking for.

Great information, thanks!

Good tutorial

Blubird is the best hose on the market nothing comes close to it!

No details in this video. I'll try another from you.

What if you have a single stage pump that pumps up to 225 ? Then the first 10 years of its life it ran 175 off and 150 on with a 4.5 hp 220 electric motor . Then at 13 years old it got a 5 hp motor 220 again . But no cheap Mexican motor no a baldor reliance industrial motor. And a 1/2 bigger pulley moving the compressor pump from around 875 rpm to around 965 rpm . Now after that work was done my brothers-n-law said did you get a new compressor he looked at it as he said that ! He said why is it not dragging the way it use to? I told him he said now I got a compressor! He worked in a truck shop and ran a dozer for half his life . They always had the big 3 phase ingrasoll Rand 480 powered compressor. But he said that’s great my compressor doesn’t run a long time and kicks off faster because it’s building up faster . It’s 80 gallon with a 3 cylinder pump and it’s the only compressor I’ve ever used that I could run a D/A and while using it non stop this compressor will cycle out it will keep up with the ingrasoll Rand old school D/A build up and kick off while running it the whole time ! Amazing single stage compressor. That’s were all the out let’s are hooked to the compressor . I’ve had to over the years replace all three head gaskets and one set of read valves in one cylinder. I keep the oil changed when I can see it’s dirty in the clear window . That’s about once a year . I’ve always wanted the dual stage IR model 253 type 30 . Great explanation of the types of stages . Thanks for sharing an I’ve subscribed and liked this video . I’m thinking I’ve bought from your eBay store front . Check valves and the puma air filters I have to make them work in my compressor because they don’t make the right ones . Discontinued 20 year old kobalt well it’s at least 18

Thank you for the video, can you explain how to wire a DPDT switch to a motor?

Exactly. Before looking at this video I replaced the pressure switch. With no luck. I watched this and purchased a new check valve. And then everything was fixed. Thanks for the video as I did exactly what you said replacing the pressure switch for nothing. Thanks again!!

I don't buy polyurethane or plastic tires on my car and I don't buy polyurethane hoses. Most of the stuff I own is decades old and will last decades more. They're making stuff cheaper in America and it's very noticeable. They don't want stuff to last 40 years they want it to last 40 months and the inflation to match. As a customer you've got to make careful decisions. You can't trust the Amazon rating system as people often times post ratings before they even get the product. I've seen products on Amazon with many many thousands of ratings 4.8 stars drop to 1.8 stars a few months later. Hybrid hose I'm just not a hybrid kinda guy.

Always wondered what the difference in stages were and now I finally know ! Thanks. Yea, I guess for most applications except filling truck tires and running big truck impact guns you're much better off with single stage.

What about Screw type compressors?

Great video! I had a leaking pressure switch, cleaned up the check valve of some corrosion and problem solved. 10 minutes of effort got me up and running again. Thanks for posting!

Jamie, please help me find the pipe thread gage on your website

If you have replaced the check valve and replaced the pressure switch and still have air leaking through the unloader valve on the pressure switch, then you may need to make a slight adjustment in the clearance between the pin at the end of the unloader valve and the paddle switch. I had this problem with a switch on a Senco 0968 compressor that is like the black one in this video. The pressure switch has a small lever or paddle that pushes a pin at the end of the unloader valve when it shuts off. If the unloader valve leaks air after the compressor shuts off and keeps bleeding the pressure down to zero through the unloader valve, check the adjustment between the pin and the paddle. There is a nut just behind the pin on the unloader valve that offers some adjustment and there is a screw that secures the unloader valve to the pressure switch housing that also offers some adjustment. The adjustment needed is slight but it can correct the leak and allow the compressor to hold pressure. Worked for me.

What I am seeing is, my exhaust valve is leaking when the compressor starts up. So the whole time it's running, the exhaust valve is leaking. But when it shuts off, the exhaust valve stops leaking and everything works as normal. What would this be?

A phenomenal video you've created for us "NEWBIES" when it comes to the various different types of air compressor hoses and their composition, as well. GREAT INFO to be armed with and know when deciding or deliberating on which type of hose is best for our specific needs or type of applications, as well. Thanks brother!!

I have a question, btw, I liked and subscribed because you are very knowledgeable about something I need help with. Well, here goes, I added a series of copper lines (and a water separator just before the tank) in a grid on the wall for cooling, about 70 feet in between the compressor head and the tank to get rid of all the water. When I did, the line isn't letting the check close until all that air in that line empties. The 70 ft. of copper line takes about 3 minutes to bleed out thus wasting a fair amount of air. Is there anyway to fix this and is this doing any harm to my compressor? It did get rid of almost all of the water out of the tank, btw.

Can a load genie be replaced with a conventional check valve if I replace the switch with one that has the 1/4" unloader nipple on it? My old Speedaire doesn't even have a switch. It just plugs in and goes. I like it because it's a quiet oil pump type so I'm hoping to save it. The noise coming off the load genie sounds like a blown rod bearing on a car.

What's that little tube/case on the top of the motor? What's inside that part?

thank u so much..

In the middle of a project to rewire motors, this was excellent.

Great info just what I needed to know!

lol... "I want to buy this brother a beer..." lol. my sentiments exactly - but not a beer. He needs to stay sober so he can guide the rest of us rookies into how to do these things accurately. Greg [garden grove, CA usa]

Very helpful, thank you for putting this together

More lost than before

If you shoot a nail thru your hose you don’t need to repair the hose you need to find a new job.

I just replaced my precious switch on my campbell house field compressor. I turn the compressor on and it fills up to a 120 P, S, I, then shuts off.....then the unloader starts leaking until the pressure drops to 100 psi then it stops leaking????????

Thanks God very much sir for sharing your knowledge.

Can I put a filter before my check valve? It keeps getting crap in it

Thanks boss, I'm a DIY and I have to replace the motor on my air compressor, this helped slot

How about the noise of both?

thank you. can a shut off ball valve be doing work of a air check valve. meaning, can the earlier one replace the check valve pl.

I was always told the poly hose is what you need as a carpenter and I’ll admit that they are tough but they are harder to roll out and roll up. It’s not the biggest issue but u can’t just wrap it up like a power cord all easy how ever you want, I love pvc personally it cheap,flexible and easy kinda like my taste in women but I recently stole a dewalt hybrid from trim and finish crew (they had it coming bunch of A holes, I don’t feel bad about it whatsoever) anyway it’s quickly becoming my favorite n go to hose .next time I go to buy a new one I’ll get a hybrid hose not a dewalt tho I’d be more than happy with a harbor freight one

Really dude? A 20-second intro + having to listen to you say 'Uh' or 'Umm' _literally_ *every single time* you pause or start a new sentence?? Umm, yeah...no thanks

I have a leak on the under side of the pressure switch it's the valve stem that's leaking. Is there a way to seal that off?

I would like to inflate multiple paddleboards as fast as possible, each up to 15 psi, with the lowest noise as possible. With the proper adapters, which compressor do you recommend? TIA

Almost made the wrong choice.

Had a bad check value so i replaced it. Now the compressor pumps up to 125lbs, then over a 3 or 4 hour period it leaks back to 110lbs. Then it stays there. I was wondering if i took it apart and stretched the new spring a little would it help? Please help if you can

Put up with it for years now replaced the switch and now realize it's the check valve if you're correct..

Is regular interval draining (as with the electronic option) important if using an aluminum tank?

Best description I've heard. Thanks.

Good stuff bud Now we just need to know what fits inside of the EGR tube nut on an F-150 Lightning (Yeah right)

Hello, and thank you for your very informative videos. I have a question, I purchased an 60 Gallon air compressor that is 230V/ 14A. I don't have 230 service in my garage, what breaker and what type /gauge wire do I need. Thanks!

I guess he doesn't answer questions online... you have to call.

I thought right the opposite, honestly.

how do nylon air hoses compare as far as in cold vs hot weather and durability?

Thanks. Very helpful. I will be removing my check valve.

Any thoughts on the zero-loss magnetic drains that don't require power?