Відео

Do you still have it amd use it ?

Looks like your bypass valve is plugged. The motor should come on as soon as you press the button without pressing the lever.

You are feeding it to fast

Loved the vid, and i loved more with the mistakes you made, and you included them in the vid to,, definitely the best iv seen as you dont hide your mistakes, and on top of that you showed how to repair something with veru hard to get parts to , iv subbed due to this bid, all the best paul

My Kohler kt735 after replacing carburator, it loses power in tall grass now and before it never did. Everything is sealed as per carb gaskets. It will start and run with no issues, even when engaging PTO it seems to lose power then it picks up after a few seconds.

I need help

For years I ran a series of 48" bush hogs behind a 17hp Bolens G174. It had three PTO gears and the 720 range seemed the most likely for mowing. It certainly worked well on the Woods finish mower which came with it. So I spun the bush hogs at 720 and got pretty good results. When I bought a more powerful Kubota with 540 pto, the quality of the cut diminished drastically.

Ty , I am going to copy your design for my pd15, I also have a b2301

Thanks! There is a $21 top hook on Amazon.

I am also 5’ 16” tall!

Would be great to have some idea of dimensions and size of lumber 1:25

Great job on bringing that old girl back to life. I just got one at a garage sale for 20 bucks. It runs great but the chipper blades are done. In my area we have ethanol free fuel at the gas station. I always use it in my small engines and it doesn't eat up the fuel systems.

Take some really long screws and put it into the 4 corners of the board then push it into the snow, problem solved

The problem i encountered after purchasing the quick hitch, new top hook, and bushing's is it's only Category 0 compliant. I found the 5/8 lifting pins to be undersized and extremely lose fitting on my 3 point lift arms. The 5/8 lifting pins are only rated for Category O and tractor's up to 20 horsepower. I found the undersized pins to be the deal breaker. I don't know why they designed the hitch with such small pins - very disappointed.

I just bought a Stihl post hole digger, you have to wrestle it a bit but saves messing around with the installation of this tractor auger. I quite enjoy using it. If you are only doing one big job, fencing for example, I would rent one of those hydraulic post hole diggers from Homedepot if I didn't have the Stihl. I don't rate augers on the back of tractors at all and front augers are seriously expensive - around $2500 from what I saw this week at the Kubota dealer.

My mower will not spin, is there a lock?

Had this installed on new 2024 by the dealer. Works great. Then I noticed this "odd" part laying on the second row floor. Your video confirmed it's the original hinge.

Thank you. Enjoyable comments on futility of being organized all the time! The duck would like to meet my workspace menace, the goat! I appreciate this direct approach to getting the job done. I have the same product and will be attempting the same repairs. Good guidance here.

Theres a weep hole in the front of it to fix the flow issue your having unscrew it a little 😊

Great idea, solved my problem!

You rock!👍

Just Another ! Running ! Commentary ! Show !

How did the wd40 coating work for you keeping the underside of the mower deck free from grass sticking?

Thank you!! My kubota zt740 would start hard, run rough etc.. after screwing with it for weeks and changing fuel lines, pump, filter, air filter, plugs etc.. this finally worked! I feel like an idiot but thank you sooo much!!

Excellent videos. I have an old pickup. Just with a 4 pin connector. It gave me an way to upgrade the trailer lights.

You can buy rod ends a lot cheaper than buying the whole gas spring.

I'm looking at one of these now, Have you been happy with the B2301?? The One I am looking at has LOW hours of 4! Yes 4! Asking 17500.00 I would like to get it for 16---16500. Should I get it, Your video will be a great help to me servicing it. Thanks!

Lmao velociraptor

Carburetor sounds like it to be adjusted. If you are seeing sparks or flames coming out of the muffler, it's running lean. Sounds like it's running rich. A correct adjustment will give you greater performance and efficiency. Great job going through the engine.

Absolutely brilliant..im doing the exact same thing..

love it !!!.. going to do this too. I have same box!

Is the lower opening where lift arms slide into same size opening as top link,,my tractor arms wont slide into bottom opening because its not wide as top link opening???Any ideas,,def want to figure a way to make this work,,too aggravating attaching box blade when by myself

Did anyone else catch “I am 5’ 16” tall” funny guy I like watching your videos

Thank you for this video. I'm going to do the same as your design and add casters so I can roll it to a corner of our shop. 👍

I use brake steer when pushing snow on ice.

Does this help when you lift it also?

no knots. How does it do on knots

Any recommendations on getting the torx bolts off? That’s where I’m stuck

5:02.... non . J'ai un B2601 et cela ne mais jamis arivé.

Nice review. They are fantastic investments.

Great video. Thanks for sharing.

The darn thing is $319 today

The real bottom line is you get what you pay for. Nothing wrong with being frugal but just be prepared for inconveniences. But I’m with ya. I try cheep and about 35 to 40 percent of the time it backfires on me. Do whatever just be mindful. End of story.

Thanks, very good explanation, nice video

Johnie hobby of slot car fame

The box along with the tire up front would make the nose heavier than it needs to be.

Man, 😂 I like your video

Thank you so much for taking the time to make this video. It has tons of great information and I really appreciate your efforts!

Hello friend, I know that this project was many years ago but I have a Honda HS35 also with that problem, I just want to know how you removed the control cover to get to the carburetor in the video it can't be seen thanks good video

Did you happen to draw out the measurements and do a diagram of what you built? This is actually the best one I’ve seen built so far and I have been looking for sometime .