Відео

Good video 🇺🇸

What size solar panel are you using with this?

Very fine organization !! 😀

Was stationed at Sembach a couple times, and Ramstein once.......loved that area of Germany! Did you need a special drone license to fly there?

Very nice 👌from ON3FMB 73`s

I've ordered mine they are a lot quieter only thing I see is the speed difference original is 5500 new ones are 4500= 1000 rpm difference airflow is almost the same original is 4.9cfm new is 4.8 cfm Hope this helps anyone thinking of changing the fans out I forgot about the noise origanl is 21.0db new ones are 17.9db

would be nice if you put the radio into the contest fan mode so we could hear how quiet the fans are at full speed 05-20 menu

A $190US for a pouch? 🤦‍♂️😂

Thanks for sharing this video and your thoughts and comments. de AA4SH Steve

❤

Nice videos man. Are you still in the hobby? I have a buddistick (original) from back in 2014 that still works well (this was pre-versatee). I run mine with my FT-857D. Subbed, would like to see more content from you. I'm particularly interested in the 3D printing stuff ~Jeremy KF4CHW

Love this video! Finishing up a very similar build myself!

Have an alternative to the 5.11 pouch? They don’t make it anymore

Merci your video help me a lot. i m tested before to close the ft891 one fan was not working, just bad connection, now it's OK 73's F4ELQ

You are one of the few people bought Armoloq. How u like it?

Soldering a silver plated terminal connector like the Anderson power pole, can be risky, if the solder runs off it'll cover or ruin the silver plating, causing it a it less good electrical connection (higher contact resistance). But if you don't care about that then you can solder it. I just think crimping alone is good though for this connector, if the wire size is a good fit.

That was the most horrible fucking music EVER! Good Vid, thanks Man.

For those of you wondering. The connectors are JST ZH 1.5mm. The fans are 04010SS-12L-AA-00 and have a similar cfm to the noctuna fans.

I never take off the screen protector as it is a perfect fit and free!

thanks for this!

Thanks for sharing your setup. Safe travels 73

what app are you using

I just got my buddistick not that long ago as well and have an 891 manpack setup similar to yours, a la The Tech Prepper. Something you may or may not be interested in; the whole buddistick PRO Deluxe setup will fit inside a Maxpedition 12x5 water bottle pouch. You'll also have room for your Rig Expert stick in the outer pocket. Better way to transport the antenna system IMO, especially if you like to MOLLE all the things like I do.

thanks, fito fantastic job 73 from kb2uew

Here is an article for an alternative method of elevating the counterpoise off the ground... ua-cam.com/video/9LnHhqSBwAI/v-deo.html 73 de Arnie W8DU

Good job I own 3 ft891 good value for money But i blew ipo att on one Still receives normal ok I was tx on 160m vertical and had it connected to my 80m dipole It was turned off Never thought it would hurt it but it did So be careful with that seems common problem with 991 too

Nice rig. The Armoloq TPA pack frames are excellent. You are right, everyone loves the Yaesu 857-D. Enjoy your radio. 73, W5SWX.

subed bc me and you are in the same boat. Everyone always talks about Gen. But with 10M and 6M and the solar cycle we have coming. I wish more people with Tec like us showed what all you can do without a Gen. great video!

Are they 12v or 5 volt, tnks

I need to get my general to get more HF privilege

I need to get my general to get more HF privilege

Thais this help me finished coping your build

Danke für das tolle Video.73,von Wien.Österreich.😊😊😊

Danke für das tolle Video.73,von Wien.Österreich.😊😊😊

Danke für das tolle Videu.Yaesu FT 891 ist gut.73,von Wien.Österreich.😊😊😊

Also amazon has a screen protector for if any one was wondering

Thanks for the video ! I was kinda concerned when there was no tape to open box did yours ? Also that is was not in plastic after opening box again was yours ? Also the stop sticker that was on it wasn't covering over from pulling off cap on end ..... kinda wonderd if I got a open box .... thanks again for the unboxing to get started with it ... 73's N7ZXG

Brilliant setup man. I love it. You did what you needed to do to make it work for you. That's the name of the game.

Did the mod today along with an anderson power pole mod. -- Great video man. Simple, no surprises and to the point! Only took 25 min to print the part. Did 80% infill PLA+ Thanks!

Nice

thanks, fantastic video and good dx 73 from kb2uew

What size and type screws did you use to mount the fan to the 3d wedge?

I am looking for about your product place lace me a message. When I post this, I am looking for more information on this Vineyard video I wonder how you got his back off setup work like that I am looking for a bag to put in off-grid or for emergency or for a zester

Congrats on the general ticket. 🎉my only attempt at a park activation was a fail because I thought I only needed 4 contacts ……ah yah that’s for summits on the air 😮

What the DC connectors you're used?

Is that bag the one you can get from Big 5, looks just like those day bags Big 5 sells...just curious 🤔

Good video. Can’t wait to see your follow up. This antenna may be my next purchase for SOTA. Thanks for making these videos.

Where did you get the cable from? I don’t want to modify the back plate due to voiding the warranty but I’m looking for that cable you have!

Kool

I’m turn between this radio and ICOM ic705 . I know ICOM is a lot more and a lot less powerful but it seems to be able to a lot neat things