Відео

I don't usually comment on videos but man, of the hundreds of videos/series I've watched trying to do this as an amateur with limited tools, your series has BY FAR been the most helpful and gotten me out of my head to just get out and start doing it. Thank you!

Thanks for the walkthrough! I'm looking to insulate a van. I was thinking to insulate just past the wood frame then shave it back before installing the walls and ceiling. I'll be using may van across the Southeast and keeping it cool will be my focus. How much of a gap did you have from the insulation to your wall? It looks like there is a good amount of space that could still be filled. Open to any suggestions you have!

Thank you for the great content and showing us how us non-professional van builders can do these installs. The background music was a bit annoying, in my humble opinion. I have a PM 3500 159” Ext and will be watching your video series for how-to instruction. Thanks, again.

Does the swivel seat lock into forward position when you want it to? And does this swivel kit that you’ve linked work for a 2016 promaster?

Wow! That looks awesome.

could you tell the total built up cost?🎉❤

its like Trial and Error thing🎉

After 5 built you sure does get things figure out i guess🎉😊

Love your built🎉

Really cool build man. How much did it sell for if you don't mind my asking? How does one contact you?

Hey great vid. It's been 8 months. Are you still happy with the Sumo upgrade? Did they meet your expectations?

Why didn't you use rivet nuts?

No insulation and sound deadening what?

You should have buried your cables in some kind of flexible ductwork so you can pull the cables in and out if you ever get a fault

1 spacer is correct for 90% of ram promaster. You should have a space of .5" of space. nice video

A pat on the back for not filling the rocker panel with foam A few really good tips for your next build Or viewers looking to get the most out of spray foam : #1 I used many tall cans of rubberized spray after scuffing panels and metal framing Along with the rear doors This does not stop cold air However it slows the transfer of forced convection (Cold air blowing on thin metal) / radiant heat..like a steel pan And a coated steel pan that takes longer to get up to temp. Any exposed metal in the van has the same results #2 With pocket holes leading into the rockers And a large gap in the rear doors You want to cover them up to spray over them For the pocket holes i used over lapping pieces of duct tape tight together (Foam does cure over it without burning it) Side note: I stuck a 5 inch long coat hanger in 3 places along, before i sprayed and removed them after for a small pressure release for opening and closing doors For the doors i used cheap plastic poster board you can buy at a Dollar store Or crafts place And done the same method. #3 Your wood / furring framing You can coat one side with the spray rubber if you did not spray where it is going to screw into (damp wood with hot and cold rots/warps/weakens it) I also done a very thin frame work to the rear doors About 3 paint sticks thick 1/3 inch? leaving one access point at the bottom of the rear doors for license plate lighting wires And made a wood mini cabinet without a door that pulls out when needed. I filled the doors with spray foam And shaved it flush to the framing Then added flexible thin paneling And spray glued my canvas type material #4 Red packing tape You will want to remove all the extra spray foam off the wood framing after you spray You can ether get a putty knife and scrape for 5 mins to a full hour depending on the mess Or peel away the tape. #5 Don't bury your wires in foam. What happens when down the road you want to add a plug in Or something breaks down And you have to replace it? Find yourself the ideal size of Mini PVC piping for the amount of wires you will have Use them down both sides of the van with 2 per side T outlets The outlets make it more simple to fish a wire thru Or pull one out Then you can foam over it leaving the T part exposed #6 The pros of hiring a pro...If you never done spray foam before By the time you understand the expansion rate And the areas you need to address first you are almost done The bad thing about that is many factors But the most common is nooks and crannies you missed And some panels have more foam And others less foam And you no longer have foam in the bottles to fix this. What was your method to know exactly How thick your foam was? is the foam the same thickness thru out the van? - The pro's have a "high tech" tool to know this And with a total of 100 gallon drums They do not run out of foam And if you say you want Min 3" inches That is what you get. #7 High tech tool. Not many bother to find out how much foam they have Just that they have some So here is my tip on the high tech tool....Get yourself a measuring ruler with inches on it Measure 8 inches on a coat hanger wire And cut it Now if you wanted the target of 3 inchs of foam measure the wire 3 inches from the tip Mark it The wrap tape around that mark with the tape line facing you ....Poke the foam hard till it stops there is your 3 inch line.....Do this on all the panels eyeball if the whole panel is level with the 3 inch mark fill as needed I have many more but this is long .....hope it helps

Great job. Well thought through nice planning.

You're gaining 1.5 inches but on both sides and so 3 inches makes a difference.

How long does it last the lpg gas ...??

Thank you for the easy steps by steps install instructions. I'm so happy with the mod and your right is super bright thank you.

Great solution!

I just finished this on my Pro master using the exact same approach. Thank you for that! However, I can’t imagine having the wire gland facing that way. It seems to me it should face the other way.

This was very helpful and informative. Just wondering, should the wheel wells be sprayed with insulation too?

Clean install..... nice job

Have been following your channel for some time now.....just binge-watched your videos again. Great stuff! Are you still doing custom builds? Im interested!

Nice work, great tips brother.

Im wanting a van and i dont have money for building a wall and all that mice stuff. Im doing a no build. Just throwing my stuff in the van and live. So what would you recommend for insulation please? I seen some black one idk whats it xalled. Please help.

Little tip, use packers or spacers in the roof to get it even, running strips lengthwise

My absolute favorite interview to date. The ministry and anointment was so impactful. Thank you Jesus for the lives you will save as a result of this episode. Hallelujah 🙏🏼❤️

Are you in Torrance, California? I'm getting hometown vibes!

Hey those are the exact same rails I bought!

will the new added headlight bar interfere with the vision of cars in front of you? or is this something youll use when youre on a dark street with no cars?

Why not put the walls up..or panels up first ad drill holes and fill

can you provide a link to the screws that you used for the furring strips? What length are they?

thank you, very helpful!!

one warning research your laws on aux lighting . some states they need covering if considered off road, some they need to be disconnected , some there never allowed to be on public roads. and the main thing common curtesy like high beams dim when oncoming traffic and parked unloading dim to the parking lights hence the name . nothing more annoying when someone pulls in front of house facing oncoming traffic causing the car to go around with headlights blinding .dangerous if a kid adult or pet runs around to get somethin in passenger side. off road great to have all light as possible

Did you go with one or two spacers?

I go to Medellin couple times a year. You just got to be careful who you meet with

The only thing I would have done differently is PL premium adhesive on all the pieces before screwing. I wouldn't trust those metal screws from coming loose while bouncing down the road.

Beautiful Sir... 👍

I see I’m 3 years late, but I am following. Thanks for taking time to film

I just installed a pair of these and they rock quite a bit, along with a small clearance issue at one point in the rotation to back-facing position. I have a 2024 Promaster 3500 EXT. The bolts fit perfectly and it swivels, just some rocking that can't be taken out via the 6 bolts around the swivel. Electrical was no problem. Thanks for your video, always good to see someone have success with a particular product/brand before tackling.

Awesome

Fantastic. I'll do the same!

No need to do floor unless you're an Alaskan.

I’d like the link to your cool mounting brackets please? Love the video and your background music is the best.

One question; why don't you use spray insulation on the floor?

Hey this looks pretty easy. I did see one video where they taped all the small holes but it looks like you hit them and they just squish out which is good. Not sure if you have seen this video but it makes your seem like a walk in the park. Great work and thank you so much for sharing! ua-cam.com/video/meO2xhBx9h4/v-deo.htmlsi=yWxZ8IbG9vjtGKVZ

You got mad skills, bro thanks from the 313

What a bad job