Відео

Can you link me your Infill panels for the boot door?

Awesome work, thanks for sharing. Ive done the front left but now my drivers side is due so this will help thanks.

Good vid, thank, I just ordered a lift kit

Great video. Very helpful. Thank you for making and sharing it! ❤😎🙏

Hey Bia, just a question with how you’re traveling with it. In regard to the awning wrapping around to the boot, and your positioning of the awning from the roof, do you get much rain coming in from that gap at the back above the boot? Was just wondering if you could shift the awning forward a bit more if you chose to, to slightly close that gap? Looking at the same one for a Paj and was worried water would get straight through or drip heavily when I’m cooking or accessing the boot. Cheers Bia.

Who asked for a walk around "build" list?

The strange noises are probably some of the suspension and wheel alignment bolts not being done up, tighten the lower should bolt to 100NM tightness all the other larger suspension bolts to 140NM that old CV is still good its stronger than the new one. If you get clicks and clunky noises from the drive line pull all 4 wheels off and re tighten that 36mm axle nut on every wheel EDit: Tighten those suspension bolts with the car on its wheels to avoid additional stress on the rubber bushings

Just a few tips from another pajero owner, those aftermarket CV’s wont last, they are a different cheaper design internally and are basically made of chalk. Your best off to spend up on a new OEM or get second hand, remove the boots and re grease as the factory are stronger, you will know if they are factory because the shaft has a thick section in the middle. You also should have zip tied the dust boot on the strut inside the spring. It’s good to see someone doing their own work ! You could have left the brakes on but it would have been more awkward. The CV you pulled out actually looked good, i suggest putting it back in it will be stronger than the new one

Thanks for the video....I love Pajero..I have a Pajero Wagon 2018 Black edition chassis old man emu..have a nice day

Hey I’ve just install a android head unit and everything works great it’s similar to yours but now I don’t have cruise control or my speedometer has stop working I plug my old unit back in and it works Have you had the same issue

Those GSP shafts are dog shit. Best off when you can find some low km replacements from ebay. I think I got both rear drievshafts delivered to my door from an NX for just over $200. Bargain for some SLIGHTLY used OEM shafts.

I'm amazed that sand bank doesn't wash away!

Most common clinking noise up front are the sway bar end links. Just remove the front sway bar. Dont need it.

You took off way more than we usually do for the front cvs. We undid the upper ball joint and tie rod. We don't have sway bars up front. Undid the inters then tilted the spindle down and cv came out. Your gen 4 has 36mm castle nuts. The gen 3 is 32mm. I would like the bigger brakes though.

❤❤❤ thank you so much for the Kind and generous Heart of sharing yours skill ❤️💪💪🙏

Hi, beautiful car and videos. What is the width and the offset of your rims?

But you can always trim the cover a bit and it will fit after that.

"Sink hole"??,,,when its just a sand scour due to current,,next it will be a tsunami because the tide came in,,😊

Finally, a step-by-step video on how to do a front CV on a Pajero! Great detail, clear instructions, and excellent camera work showing parts, bolts, specs and tricks. 10/10. Keep them coming! FYI for others watching: the two bolts you’ll need to help take off a stuck brake disc are M8 x 1.25.

Thanks for sharing. I now feel confident to do this too.

Hey i just stumbled onto your vid as im researching on doing the same to my 2011 platinum pajero. Have you got any more wisdom you could share with me since youve done the upgrade?

Hey Bia, check the sway bar D rubbers for the clunking. Easy enough to replace and cheap enough to be able to do front and rears.

Good shit

3 inches？

one month out of warranty, That is a perfectly engineered product.

What on earth is this ? Cringe

Its impossible to block and do not recommend this channel, I have tried for 20 minutes now! Great stuff on stuff. Roaling coal is great , i kinda feel a bit forced here tho lol

Well done Bia brilliant seeing you get stuck in . was a bit worried you didn't drop anything onto your feet with just your flip flops on . saved yourself a lot of money there doing it yourself 👍

hi

You sent You know what? I am a regular viewer of your UA-cam Channel. I have seen all your videos and your content qualities are very good. I learned lots of things from you. Your channel has great quality contents but still it is not delivering its right audiences due to SEO problems. You should focus on your SEO so that You can get a big fanbase. Thanks.

Great mix of content, enjoying your videos

Whats the impact driver and the ratchets brand?

Hey Bia! Please keep us informed about the clunk noise. Is getting clunky in my Pajero, also. Although I don't know if it is the same clunk you hear. I suspect, the swaybar bushings on my car, cause it only clunks when I go over bumps.

Just a suggestion. Don't wear sandals.

upper front ball joint

Hello, Bia 4x4-SYMMETRY 4WD-DIY with Brian-How are you?? Hope you are well, recently I have looked to your channel. And saw that in your channel have many many problems, for this reason channel videos not getting much engagements. Not growing, If you can solve these problems, channel will grow, You want to know these main main problems??? I can tell if you want to know. here or in email!! Where?????

Thank you it’s very useful 🎉

Hey I’m thinking of getting this colour Pajero. Have you ever owned a white vehicle and do you find this mid-grey one gets much hotter inside after being parked in the sun?

Bia, you are beyond incredible 🏅 I would have lost several fingers attempting that😅

Good honest simple instructions well done

Where u purchase unit please

Great video Bia well done 🎉

Hey ime about same with arb bar same as yours and exploring how to fit without cradle

Thank you Bia for bringing back memories of 25 or so years ago when I came over from the UK. My brother-in-law had a 4x4 and we drove up round the island on the beaches. Something unheard of in the UK

Thanks for sharing Bia, you have done a fabulous job on both land (sand) and in the air. We are leaving Melbourne in 2 weeks for the Cape and stopping over at Fraser Island for 4 nights en route staying at Central Station very much looking forward to it. All the best.

Nice plenty of cover keeps the sun and rain off

Just found your video on suspension replacement front and back, just paid someone to replace my front struts,after watching you do itl wish l had done it myself, a very good video, now l will tackle those nylon pads on the back,question, are those pads only on bottom or top as well??😊

Watching video from the driver's seat is not legal- Most ADR certified head units will not allow!!