Відео

44

44 litres***

10.5 gallons

Oil drain pan in the newer paccar engines does, yes. Just short little twist and its locked in. Older ones are a standard plug

Hi. You can contact me at NYAMechanic2000@gmail.com

thanks

Hello sir, are you talking about the exhaust and intake valves? We use Dello 400 across the fleet as that is the factory recommended oil for some of our trucks. You will need to check your owners manual for the best oil.

@@noturaveragemechanic7121Hi dear friend I mean the camshaft, my car's engine is a retarded 3-stroke engine. My mechanic opened the engine and said that you used too much retarder in the engine. MX13 engine, you should not use a retarder in the engine because the camshaft will break quickly. with regards

Clearance no, new bolt, no. I did torque it later but completely forgot to film it. I'm out here simply trying to help owner operators and small time mechanics get a job done

@@noturaveragemechanic7121 those bolts stretch out after one use/torque down so when you torque it down again it’ll be at the wrong spec. If you checked clearance you wouldn’t have to do it twice. Just trying to help bud

ISX after 2010 was common rail.

I've never come across an issue like that. You might want to look into that. Constant fuel suction sounds Interesting

77 inch pounds. And then 30 foot pounds and then 60

After I installed rings my truck idles at 1000 rpm now and suggestions

I only service our own trucks so there is a lot of space that I don't use.

I have never had that happen to me. If this ring didn't fix the problem it usually ended up being the head gasket or other issues in the head so I replaced the whole head. I do not know if there is a tool to pull them out.

​@@noturaveragemechanic7121 Thank you much for your reply I found two companies that make the tool to remove the original cup without removing the head. one is call Irontite, and Industrial Injection services i dont know if this will help in any way I installed all 6 rings truck will leave on a short run for testing purposes i hope i fixed the problem thank you again

@@adanponce4401 hey adan I installed the ring but still getting coolant in fuel what did you ended up doing thank you

@@manuelmoreira9896 my truck is still running strong since I installed the rings Last week I notice very little coolant in the water separator…. For the first time since the repair Truck has 1.1 mill miles … I think it’s time to do an overhaul Unfortunately the rings are not a definitely fix Good luck

@@adanponce4401 thank you for the response how long it's been after you installed the ring ? I did an imframe to my engines 3 Monta ago did not put a new head I only had it rectified at the machine shop I agree I think rings may not be best option in the long run I think I ll.justndo the injector cups to be done with it

That's good information to have. Thankyou

I don't even change it anymore damn things a pain to get out

@@alexeckman5542just smack the ground and itll pop right out

I'm doing the best preventive maintenance I can since some drivers don't actually care or check up on anything

Bob is the Oil Guy as well. All though the test he had will not pull up any longer.

While yes that is true I do this for a small fleet and I do things quickly. It takes a long time to draw into the filter housing using only hand pump

Sometimes short cuts don't pay off when we're talking tight tolerance parts that contaminants in fuel can wipe out expensive components in these high pressure fuel systems, 5 microns can't be seen with the naked eye.

170 primer strokes is cheaper than thousands $of destroyed fuel ⛽ injectors and high pressure common rail pumps

If you do the one on the frame first then the primary, you don't have to pour anything in.

The 22 model 579 with the MX13 no longer have frame mounted fuel water 💦 separator, only 2 filters in module on engine.First filter had high restriction at 9,000 mi on brand new truck.At 67000 mi haven't had First oil change yet but already 4 fuel filter . Fuel algea already started from transport buying cheap southern fuel.

No I did not

Quick question...Im about to install a " USED" INJECTOR...do I have to re-program it into the ECM?? Or input the numbers of the "USED" INJECTOR into the ECM?

Just send er bud.

Solo cambio los injectores cuando terminan su tiempo y ajusto el freno de motor cuando ajusto los valves

@@noturaveragemechanic7121 exelente, que bien 👍👍 siempre que subas tus videos los veo muy interesantes saludos desde colombia 🇨🇴🇨🇴🇨🇴

B

I personally have never had the issue and don't have the knowledge to answer that. It seems like it's possible though.

You probably don’t use full synthetic either loser

Online. Cummins doesn't build them anymore

@@noturaveragemechanic7121 they are still out there found them and the same tool for cheaper

Cummins