Відео

That table gets some use!! I just put a 4x4 table together with a my plasm and a prime weld cut 60. I love the myplasm but it loses connection with my pc after the plasmas first fire. The program then freezes and I can’t move the table. Not sure what’s going on.

Shop looks great! Thanks for the great content!

Does the propane tank need to be manually cut off when the PID turns the Heater off after it reaches temp? My heater seems to get an extra "blast" of propane after it gets turned back on from the PID and seems to run too hot.

Keep going your doing good

Thank you, sir, Mr. buddy appreciate you taking the time to do this video. And I’m right there with you if it is simple and less complicated the better.

Hahaa freedom!!!! Congrats man. Super stoked for you and your family and cant wait to see what cool content you can produce out of this new space.

Grow tents (4’x4’x8’ feet) make really good powder coating spray booths, they have lots of vent holes to hook up fans and are reasonably priced (I paid only 80$ for mine); and also very easy to keep clean because of the reflective Mylar that they’re made out of.

Nice !

Nice work mate ! Must feel pretty good upgrading!

Good upgrade man. That's awesome!

after the vinegar bath put them directly in a baking soda solution or household ammonia solution to prevent "flash rust" by neutralizing the acidity

Nice work

They look good man

Are you still using the oven you built from the freezer? If so does it still work well? I’m fixing to build my own and I was wondering about some feedback after you have had it for a while.

I've used vinegar to take mill scale off for years, and it works great. Given that I tend to want my end product to be bare steel, clear coated, I always scrub the steel with a wire brush in a baking soda/water solution to prevent flash rusting. Since mill scale is the result of hot rolled steel, the bigger the piece the longer the vinegar takes to work.

Hey mate you can rotate objects in my minicad and nest them in a group then send them to my plasm and nest them together to save material bigtime, love your work mate back to work haha

I'm building a small CNC plasma table using v-slot extrusions and nema 17 motors for x,y,z axis. I'm at the stage where I will need to build the control system. I'm new to this and trying to decide what electronics to buy. Looks like I will need motor controllers (one per motor) a power supply, and a breakout board. However, I read a breakout board that connects to the computer via Ethernet is less prone to HF interference than one which only offers USB. Can you make any product suggestions for me or offer any advice? I would like to have torch height control. This software looks like a good choice. Thanks for the vid and info. Subscribed.

This is cool. I love how the powder coating booth turned out 🙌🏻🙌🏻 🙌🏻🙌🏻🙌🏻

Love this video man. Its awesome to see the progression over the years. 🙌🏻🙌🏻🙌🏻🙌🏻

How do you like the manual brakes? I just put some on my S10 and the pedal is really hard and I feel like I need to get on the brakes harder than I should to stop. Not sure if I have done something wrong.

Help me out on some info I’m building a oven also was not sure about propane heater but seems to work ok I’m gonna try this out thanks

is there any power on the garage door or do you have a 2nd filer on the back of the fan to catch as much powder as possible?

Looks incredible!

Nice job

Thanks for the great video, I'm following along with something similar and have a very difficult time finding the right brass fittings to connect the brass adjuster to the solenoid. Do you know what size brass fittings you used? Thanks!

I put 3 inch holes for back air

Hey I made oven 4x4x7 ft and I use mr heter and when I start air come back and heter wires barn

With the type heater your using, unlike an electric element that heats static air within the unit, your forcing tons of air into a sealed box so of course, you have to let an equal amount of air OUT of the box. lol Instead of just venting the box, run an insulated dryer hose out of the box and back into the air intake for the heater. This way, your allowing the heater to still pick up fresh oxygen to burn but at the same time, your recirculating pre heated air rather than wasting all that energy into the room. The trick is to not completely block the intake or it won't get the fresh air for the burn.

Good informative video about the white vinegar for I have been using it for years. But have found something far better and cheaper and it works far quicker than vinegar. And is only £1 a bottle it's Harpic 10x and it very fast working for mill scale and rust removal, it's all I use now for it's brilliant. You can also paint it on with a brush let it sit for a short time and then just rub it off with a cloth (wear gloves) wash it and finish it with a rub of light oil to prevent rust.

You have got to be kidding me! I have to try this.

where did you get the latches?

White vinegar will save completely rusted shut pliers and socket wobbles too, just soak for 24-48 hours and they are good as new !!!

If I was you I would return the gun back and get yourself a Nordson and you will never have a problem powder coating that gun that you got is not that good.

Thanks for this! I was just researching this setup.

keep up the vids love them

love it i am to make sword I have been looking for a temper over and i think it will work for me

Jam nut on master cylinder rod? Nice job

My guess is the issue with your cured part was caused by back ionization. Try shooting your part at a lower KV setting and see if that fixes it. Also, you mentioned not trusting your heat gun because your part was showing 400 degrees quickly. That's such thin metal that reaching 400 would happen in no time. You could expect a pair of brake calipers (for example) to take longer. Lastly, how is your spray booth grounded? If you're not using a 8' copper grounding rod (easily sourced at Home Depot) you'll never see that gun's true potential. Mine is planted just outside the shop and I ran 12 AWG copper wire inside attached to my hanging rod. If you're cringing about driving a 8' rod into the ground (it's a HUGE PIA!), there's a way to install one in a couple minutes by hand, no tools and it's ridiculously easy. Happy to share if you're interested. Great video!

had to send a new message this thing wont let me reply ordered 2 days ago and its on the way thanks for the reply.

Hey, thanks for a great videos series. I am in the prosess of building an oven here to. How about making a follow up? Would love to see that thing in action, meaning to see you coating and curing. Greetings from Norway.

Did you get this figured out? I hate when everything goes wrong I just ordered one from these guys and I"m hearing pretty good things about the customer service.

What did you change on the heater to make it come on and off? Also does gas leak when it’s not running?

Hope you still are happy with your purchase. I really like having all of the controls on the front in contrast to those with digital knobs, menus and sub-menus. THX!

Lol yep i too surprised when my motors came in and also pulleys too even my adurino but oh well i tòo am big a guy its all small saw measurements in my mind i was dealing 1 hp motors lol

With a little extra research I did what you said and just pulled out my third recumbent trike tadpole frame. Dang folks think I'm all smart and stuff. Thankyou Sir from a new subscriber. God bless from northern Ontario. In the spring I'll try to post some pictures.

Well Sir I just come a crossed your videos. I have to say thank goodness you didn't blow yourself up. I'm 73 and I just started building tadpole trikes and wanted to powder coat the frames and now with your videos and 2 home oil tanks I have a 4ft x 4ft x 5ft powder oven. I insulated with safe and sound then covered it with metal roofing. I used the glass from an old kitchen oven with oven bulbs. Again Thankyou Sir. God bless.

Thank you for your prompt response, the primeweld cut 60 is HF, isn't it?

Hello, your videos are very good and illustrative. What plasma cutter do you have connected to the CNC? I just received from Proma system the board and the interface with the voltage divider to mount on a CNC that I am making, haven't you had blocking problems in the Proma electronics due to the plasma frequencies? Greetings.

The powder is just falling off at 15:08. I'm using the same gun. And sometimes it just need to be above the item. So the powder is just falling to the painted surface and it becomes oversprayed. Have you figured out how to decide this problem? Thanks for your video.

You could go with the cleaning vinegar, which is a 30% solution instead of cooking (either 5% or 10%) solution. Might wash parts down with paint thinner or similar immediately after, to stop flash rust.