Відео

11:30 - хули не показал сколько накрутил большой пылесос? меньше деволта?

Thank you for the video. I had a problem where the rollers that the belt ride on, have rubber that grips the belt, and the rubber melted off. I bought replacement rollers and managed to replace one very easily. The "drive" roller on the other hand, just can't figure out how to change it out. Fortunately, that roller still has some rubber so I will use it for now. I was wondering if you could make a video or direct me to someplace that can explain how to change out that roller. Thank you

Regarding the HEPA Filter, the main reason for it is likely due to the filter from fine dust such as drywall or other types of fine suspended solids = a very wise design in my opinion and for the longevity of the vacuum's life.

I bough

Knipex NEXT!😂

Very good video and especially for your thorough and clear explanations for each meter function. Thanks!

very interesting!

Just out of curiosity, was the fence out that much when you first got the saw? I believe the saw adjustment wasn't really necessary (.0005" is more of a metalworking tolerance than woodworking), but .0125 is marginal. Does the manual specify the tolerance for these measurements (blade/arbor runout is another one to check). Thanks for the video.

I appreciate the heads up about the silicone brush. I’ve never used one so I don’t know, but I was considering getting one. I think I will just have to stick with my finger. Thank you for your review.

Eww dewault

It's a stubby mid-torque impact wrench. 650 ft lbs is a lot for it to break. I own the DCF921, and it has never failed me working on my car. However, sometimes you need to bust out the heavier tools, as there is a limit to the force that you're going to get from an impact with such a compact housing.

If that thing scares you and if you have nails bouncing around you don't really need to work with any tools without knowing safety 1. Put a bucket under where the nails come out 2. Don't put it on your body 3. Put the damn wood on something hard like a table and a hole where the nail is coming out

Is the Bosch good for sheets meta

Knipex pliers are also incredibly useful as piers- because they have paralel jaws and can produce a huge crushing force-making them great for gripping - crimping and bending - i have a small and a big pair and use them everyday

Very informative. I may have missed it but roughly, how far off a wall would a Bridgeport stick out. I have a shot at getting but need to make sure it will fit in the area I have planned for it….thanks

Most comprehensive review I have found out of the 10 videos I watched. Nice job

If you use a grey backing sheet, as opposed to black, the auto exposure system in your camera won't make you so over exposed. It sees the large black area and tries to make it gray, this makes gray things look white.

Tip: For the loose quill lock, you can easily install an O-ring between the lock and the head. It's a 2 second job 🙂

Maybe try a T bit style screw. The Phillips bit screw are horrible and they camber out all the time. Great review!!

Is it Hepa like Makita?

Been using this every day at work to clear up solder and wire cuttings. Not really sure whats wrong with it.

Good stuff.

Used to cut a 5/8" bolt. Effective and super clean cut. Fast. Handy compact tool,

great review - very practical and well presented ... cheers

I would of put the Z axis on the knee instead of the quill since you have more fine control and is more rigid and just get a caliper for the quill.

Is it actually better with Powerstack battery than regular 5Ah?

Thank you! I’m going to use hide glue titebond to float tongue and groove solid oak over cork, thinking it will be the healthy choice as it is more natural. The wood is unfinished and will be stained with tung. At 500lbs strength, it should hold up rather well! That was key information for this uncommon situation.

What tooth count did you use on the 3 inch flat metal? 10TPI ?

I dont think anyone mounts the scales sideways most lathes will mount them in the downward position, you can change the decimal point to where you want, you do not need tape. I have had 3 of them on different machines, works perfect, The manual with mine was spot on,

Is it BRUSHLESS? That's kind of important to me.

This multimeter was a game changer for me. It's so straightforward unlike the one I had before. I just wish you could check the amperage.

Oh I see how it's supposed to be set up now My bad seems like that handle should be on the opposite side though

Did you install the handle on the wrong side of the stand? Isn't the handle over there by the wheels supposed to be on the opposite side

Why your intro is sooo much louder then the rest of the audio in your videos? 😣

That shallow socket is not doing justice. Use a deepwell socket, should zip it right off.

Great tool review; great representation for the Flourescent Community

Nice eview just bought one in walmart

That's the same manual that came with my ToAuto. I mounted the scale to the cross slide on my 15x58" LeBlond and the encoder to the carriage where the follow rest would mount and I use the shield. Slot in the scale is on the bottom on both scales. Set an indicator on top of the slide and move the cross slide to level it. I only used one of those L Brackets for the encoder for the rear that mounts to the carriage. I have no issues. I can send you photos if needed.

the f is up with the kids music bro

nice video dude...subd..ps im an engineer and you did a great job

What is the S-type load cell and screen display that you are using?

Nice video and tests! I'm a titebibd 2 user, though I'm more on the construction side of things with trim work and and misc wood projects where rapid glueup time is much more of a concern. I also reason that the water resistance will help with overall longevity of the joints as it will resist humidity and unforeseen moisture condition though I dont have anything to back that up. If i want a longer glueup or it is for exterior work i go with titebond 3, I generally don't use titebond 1.

Great review! That see through cutout mostly kills the left-vs-right debate. Powerful saw.

It would be great if you could do a comparison of this router with the Bosch 12v router that you reviewed about a year ago. Thanks!

Looking for a glue for a guitar neck. Will go with the 3.

Awesome review! Thanks for all the info! I much prefer these honest reviews as oppose to all the sponsered fake reviews on UA-cam.

I have no use for a router. But these reviews are informative.

Is he to heavy ? Nice video ...

I was laughing all review 😂

Useful demo. Here in India the variant with back rest is 101+