Відео

Hey brotha, I bought the heater hose connector AND the bleeder valve cus another video showed that their g had the bleeder valve on the driver side. Mine doesn't. My passenger side connector blew up so I was going to replace "both". It should be cool to install the bleeder valve instead of the connector to the passenger side and use that to bleed yes?

Good video, But I could hardly hear you because of the music. Overall, you did a good job of explaining what to do and the purpose of it. keep it up!

would the 90mm and 120mm work too? i cant find the 110mm anywhere

What's the Halo diameter

can anyone tell me why my controller don’t have power? controller only comes on when i plug it to any usb port like my dashcam. i fuse tap to the cigarette fuse & the blower but the controller still don’t turn on. i went over all the wirings n everything else work but that. changed the fuse tap like 3x n even used the one that came with the kit.

Putting it back is the bitch

Is it soild plastic doorcard of soft plastic?

Alright so I see everyone in the comments saying they was both looking for installation video just like me. So y’all put it on yourself or found somebody???? And if you who? I paid $500 for kit & I’m really not trying to waste it

How are the halos themselves holding up?

I did my rip out yesterday and just to let others know, during my endeavor, I experimented as I went. I disconnected the AC box (I had labeled them) and was able to even start my car, but it wouldn't shut down when I pressed the button (2009 G37 coupe Journey). I was testing per cable to see if my car would start since part of the reason I'm replacing my radio is also trying to chase down an electric issue. In order to get my car to shut down I had to connect the AC box with the car running. I'm not proud of this, but wanted to let others that are as daring (or crazy). It worked fine, and like a computer's IEEE cable, they're not likely to fry a computer's motherboard by hot connecting, though it's not something you'd usually risk either, thus one of the reasons S.A.T.A was favored. Anywho, great video. Just got my kit from Amazon and the directions are a nightmare. Only seeing this video now and hoping it can clarify some of my questions, though I have the AOONAV (currently the only available one on Amazon for the G37) and my cables and connections on my unit will most likely be different. You already clarified a few things in referencing what each cable actually did, like clock power and others. Thank you my good sir!

Can you skip running the ground wires through all that and just ground them to the body in the trunk?

Thank you

I’d be surprised if you reply to this lol but I followed every step in the video. The only issue I’m having is that the audio isn’t working for mine. That black decoder box I can’t seem to find any plugs that fit into it

🤦🏻 bro really used a dremel to open the tail lights. Wow !!! And I thought I was dumb. It’s called heat gun bruh you gotta watch UA-cam videos before actually making one and fucking up those tail lights. Definitely won’t attempt this to my tail lights. I’m done here. NEXT !!🤦🏻🤦🏻🤦🏻🤦🏻🤦🏻🤦🏻🤦🏻🤦🏻🤦🏻🤦🏻

So you didnt flush it out with distilled water? You just drained the old coolant and added new coolant ?

Looks great! Not sure I can do it myself though

@1buildmedia what the brightest HID bulbs is the best for this car am in jamaica

Yikes, not using Nissan blue? good luck with that

Is it more powerful then the factory radio

if i buy the halo kit does it come with all four halos or do i have to get multiple quanitity's

This is by far been the most helpful install video for these screens. I was able to get my camera working with the re-pin, appreciate that info. However, I am still having the following two issues and wondering if you ran into the same things: Car info: 2010 G37 Sedan with Bose and No navigation (similar to yours I believe), Radio info: Rhino PX6 13.6" Android 9 screen (looks to match yours exactly) All functions work (BOSE sound, backup camera, carplay/ZLink, wired carplay connection, hazard lights, passenger airbag light) except I'm having the following issues. 1. My AC controls don't work however the auto-blower turns on when I start the car. I just have no control over them. I'm using the same plug that you recommended for yours and the A/C controls show lit up like they are working but neither the buttons or on-screen controls work. I believe I tried the other plug from the main harness and got no A/C blowing upon start up so I don't believe it's that one. I can almost live with this since the auto-blower does a good job of matching the temp inside the car but would be nice to have. I already did a lot of troubleshooting with the "Install set" and making sure it is set to QX70 (matches my CANBUS), Protocal Tangdu and G37 car type. I have tried a few of the other options but they haven't worked either. 2. If my car sits for longer than a few hours after driving, I have to jump it to start it, like the screen is leeching battery. I have gotten an alternator test, changed out batteries, and replugged the harness in but no luck - always seems to drain it down. The screen appears to shut off completely when the car is turned off and I did not have this issue when I swapped back to OEM radio for a few days. Any suggestions? I had a Px3 for a few years and wired in a step-down to get the factory camera working on that harness so I have a general idea of what I'm doing but have not had any luck with this PX6 and fixing these last 2 issues. If you didn't run into them, perhaps it's my harness but Rhino has not been very helpful and only send screenshots I've already seen from their troubleshooting guides. I wanted to check with you before I tried splicing into any wires or requesting a new harness from them. Thanks again for your walkthrough, as I mentioned before this has been the most concise and accurate guide to getting the PX6 radio (at least the on I have) installed correctly.

How long was shipping on this ?

How do you get the big red piece back on after you cut it out.

I'm so late. Just installed mine today, haha.

Hey got a question, currently working on a project doing the quad halo set up. I have the red halos going from black>to black Red> green , white> green and white And i have the switchback halos yellow> green with yellow and i have the black fused with the black from the red halos both going into the black from the oem harness. However when i brake the ambers turn on instead of the red. Any idea why? I only have black and yellow going to the harness.

At 1:45, what is the inner diameter of that hose? I need to replace that part

You know you didn’t have too use a dremal you could of used a heat gun too take them apart

what year is this car in the video?

nice , how is it holding up ?

So the diode dynamic turn and tail won’t work for halos ?

If I wanted to hear loud music I would go to a concert. Turn the music down so I can I interpret the accent😡😡

Did you reinstall the plastic piece that holds the ballast/ignitor cable ?

Could you not wire the halos directly to the circuit board?

Bro I need your help putting n my screen before I burn it up

To glue the LED strips can you use hot silicone? I would like do it with halo and RGB trips… yours lights are fireeee🔥🔥🔥🤙🏾

Did you use 110 or 120 mm

Hey this was a good video but im hella confused on the wiring part and how you got the angel eyes to light up after you put them back onto the car any advice or tips

i have a 2008 is it the same steps?

is it easy to take the trunk reflectors off too and spray those black? I dont like the mismatch

Did you bleed all four brakes ?

Do you leave the car on during the whole process ?

Did u have to install new camera for the back up camera or is there a connector u can plug in with the stock one?

Has anyone tried this on the convertible? Do the same parts apply?

Could you use a heat gun to remove the lens?

Am I allowed to have these purple lights on my infiniti in California?

Your video needs more recognition for helping us all out! I have the coupe so the steps were pretty similar thank you!

What drill size u use

Did u have any issues with the sound it doesn’t sound as loud as it did with the original rsdio

How much coolant did you end up filling it back up with? Including the reservoir tank.

I see u have 2 front lips and I wanted to know what’s the first one