Відео

You are still the man in 2025!!!!!!🙏🏽

Very clear your video i was struggling with others videos kind of confusing 😊

So what happens if valve is stuck open

Go and bye a nuts cuter it's more esiy

Can this work with point of use faucet, it's the little faucet next to main one

Got to thank you amigo for this video. Saved me a lot of time trying to remove the drum by hitting it every 30deg or so. Appreciated it!

my autozone PCV valve had me scared thinking I was having lift ticking. Or a shorted electrical issue. I am NOT buying ANYTHING from AZ that has to screw or snap into my car!!!

Except your handle is upside down. Swap it with the other handle on the other side lol

hands down, BEST video explaining the process. Thank YOU!

My temp gauge stayed lowed. I'm changing Tstat. Hopefully it gets fixed.

they cost like 5 bucks just change it

If its leaking the ball bearing inside is worn out of spec. There is no fixing that

Super helpful! Thank you so much!!

Thank you!!!

This was really helpful! Thank you

One of the best fix it videos on you tube I have ever seen. I just picked up this exact saw today and am going to buy a repair kit for when this happens. If anyone knows the part# on amazon can you let me know Thanks guys

Thank you so much for the video. Easy to follow instructions. 5 Minutes to fix it. 😀 30 minutes find my Instrumentation Screwdrivers ☹️

That's Why I Bought Me Those Ratchiting Wrenches. & They Realy Came In Handy When I Put New Batterys In My Powerchair.

Dudes, just blow through the darned thing. Air flows one way, good. Air flows both ways, not good. Also, it is pretty easy to end up with a brand new valve that leaks. I just checked two today. One was good and one leaked.

Thank you 🙏

Excellent explanation

Pero porque hay que quitar tanta piezas ?

Great video! Mine is not dispensing hot water. It gets warm, but never hot. The inlets are clean. The flow maybe seems a little weaker than before too? Not sure. Thanks!

Thanks

I sprayed wd40 on the barb to slide it easier . Great content. Good job.

Thanks a lot appreciate it ..... I was able to replace my rear bumper

If you soak it in toilet bowl cleaner for 15 minutes it will be like new. You have to use a can of compressed air to clean it. Thank you so much for your helpful video.

My 2005 honda civic just started getting hot on me today, I just went and bought the parts. I hope that's what's wrong with it..wish me luck. Thanks for uploading this video

Fun fact this is 100% identical to a Inglis washing machine

What the number of this part?

,My God,what a pathetic video!!

I would only replace it , always not clean it .

Couple years ago i did some CR V pcv valve investigation - looks like oem part (but even them aren"t 100% airtght) needs to be cleaned from time to time only, most aftermarket ones are poor quality, specially their valve plate mashining is bad, univen suface let to much air goes through. Thanks for your video and wish you all the best.

That bearing on the end seems to be the one that fails. I got the rebuild kit with 3 bearings and brushes, but just changed the end bearing opposite of the blade because the others seemed OK at the moment. Good info, thanks.

Where do you get the rubber piece to go around the bearing

Craftsmen trying to say that little motor is 3HP! Its impossible to get that from that motor.

Thank you! I really appreciate how simple and clear your instructions were.

Nice repair. Going to try it.

6:19 I can’t pick it up… what can I do?

Thank you

Well played, sir.

Very thorough step by step video. Easy to follow along. Thanks, your video made the difference!!

Is it safe to change position of butterfly valve during cleaning? Does not affect sensors in electronic compartment?

Thanks for this great video! It was so helpful when I was taking apart my washer to replace my drive block!

Thanks!👌🏼☮💜

What about putting new ends on? I have the same situation - cut my hose in half with the mower. But I'd like to turn it into two 50' hoses. How would you do that?

Question, anyone who knows... I bought a new OEM PCV. I blew into one side horizontally (the way it is installed on my engine) and it had an air leak. Vertically, there was no air leak. I returned it and got another one, but the same issue? Maybe my lungs are not as strong as an engine! What do I do? Order another one? On my engine (toyota) it is a difficult R&R.

Good job! I just disassembled mine and ordered a rebuild kit. I’ll use some of your tips when I do the rebuild. I especially like the tip about lowering the blade to get better access to the motor mount bolts. Thanks.

Doesn't work

Great video. Saved me a great deal of time.