Відео

from 80 to 120, 240 and finaly 320 grid. thanks for this detail

What helps me with cutting board glue-ups is to use an edge (not top/bottom) caul that runs the entire length of the board on both sides for clamping. That way all of your clamps are connected and pushing evenly on the same two surfaces. You had some clamps directly on the board and some claps with protective pieces, so it would be very difficult to apply equal pressure, because they are not working in unison. I enjoyed the video, thank you. Subscribed.

REALLY, REALLY BAD VIDEO--GET OFF UA-cam!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!

I loved this, a true to reality project! Not only did you show the mistakes and laugh at them, you plowed through and got it all done! Amazing and thank you for a great laugh and great video!

@Jezzer147is quite correct, you will have better luck going the proper clockwise direction. But you have to learn, I messed up a few grooves learning too. Practice on some scraps first, you'll be glad you did! Nice board!

Hello , for me putting together a router sled is similar to putting together a train set . What I mean is that I’ve tried making one before and I made plenty of adjustments since the old design , now my rails are being glued in my brace , the materials I used the last time were too thick , so now I learned that thinner material for the rails are much better for the size of my router , you learn how to make router sleds you’re way I see many different ways, and different materials, but mine is still in the learning and growing process , I want to make oak cup holders for vans and suvs I exchange the grain and glue different types of oak to make one board and when it’s router planed and sanded it will look very sharp , well that’s all for now my brother , all the best 😊

Hey Man. Thanks a lot for sharing your videos, I just found your channel and really liked this video. Could you tell me how deep do you put your Router / how many mm you take down from your wood. Like 3 mm or more. Thanks for your advice and best regards from Germany. 😊

Simple sled anyone can make as long as you have a joiner and planer already that make the sled obsolete 😂

This is edge grain not end grain

Great video mate, thanks for sharing

Thanks for the video. You are the only one who has emphasised getting the frame flat. I think you could have gone a bit further though and used a laser level but if you don’t one of those then the “Winding Stick” technique would be adequate (youtube vids available). Good stuff, thanks.

Good video idea, but you need to remake it with proper volume. sorry it was very annoying to try and watch

Cheers for the video mate, great inspiration and the board looked awesome. 1 tip I could give would probably be get some scrap pieces the same height as your board in the juice groove jig. I did notice a slight dip on the side of the router while you were routing it out. Other than that. 👌🏻 +1 subscribe

Looks amazing mate, just don't give up good luck for your next project 👍👏👏

Brilliant mate good tutorial and an Englishman 90%of all the videos that I've seen are mostly American so thank you I've just started doing and making cutting boards So some good advice ❤

Great video do you have the measurements in the wood species order will appreciate

Great video I appreciate. The measurement is very much so I can make that for my honey

Nice work mate looks awesome, my uncle has always said to me that it's the imperfections that make it perfect ☺️

Hahaha. This is most i have laughed durong a cutting board video 😆

Lol!!! Funniest finish to a woodworking video I ever saw. I was crying when you were burning them!! Thanks for that laugh... Maybe mount them on 1/4 ply.... At worst it's bit bigger blaze at the end😂

“Hecho en México 🇲🇽 “ apá

Another great video, thanks for sharing 👍 What is the purpose of the acetone please?

I just bought this machine from an eBay seller. I loved your video ‘trial and error’ just the way it do things 🤣

Amazing cutting board!

Anyone else find that if you use your finger to spread the glue your phone fingerprint detection doesn't work? Even after a good wash it's still hit or miss. Beautiful board, btw.

Was this £1500

Hi thanks for your videos your manner and how you put things across are just right, I'm very new to this and learning,all be it slow from what you do. Thank you, Geoff

Looks good m8 congrats on the 1k subs. You'll be getting tools and stuff offered to u now. You'll be joining the laser club next. Wee tip mineral spirits works well for rubbing down in-between sanding dries instantly. 🏴󠁧󠁢󠁳󠁣󠁴󠁿👍

Now that you have got some suggestions can you please redo with the correct method.

muy bonitas las dos mesas al final, buenos colores 👌 un saludo desde medellin - colombia 👍

That looks really nice. I wasn’t sure about the gold but it was a perfect choice.

Nice change

Great looking board! What rpm did you use when flattening with the router sled?

It's amazing to watch your process. You have a true mastery of woodworking.

Impeccable work. This looks so complex to make, and your craftsmanship is top notch.

Omg 🤦

When you cut again in strips is it still at 1” for all the times you recut and glue? Then cross cut at 1 1/4 and glue up?

Beautiful!! What were your dimensions?

That's looking good m8 one thing a have seen is cheap polishing compound works just aswell as the expensive stuff. Although someone must be feeling flush playing with resin walnut and new tools!🫢 How's the buffer holding up sommit ave been looking at. Also congrats for getting over the 1k sub mark you'll be making money off UA-cam now?? Sponsor offers coming in yet?? 🏴󠁧󠁢󠁳󠁣󠁴󠁿👍

Ok i know was not funny but you made a comedic relief out of it and your expressions had me 😅 to much...ty now i dont feel so bad at my mistakes

Beautiful board and ty for tip

Love your video's...what varnish are you using...ty

Bravo!

Very nice so your dimensions were 18” wide by?

Ficou muito linda éssa tábua parabéns é show

The work bench looks great , do you have any issure removing the fence with the space you have in the back. I made the mistake of making the opening too big

Very nice! I like the wide juice groove too!

I like what you did with the bath there! 😂

great job

What the hell are you feeding the dog?