Відео

i used 10mm for penumatic application in the pvc fuel line since​ the time of my post almost 2 years, it still work no leak. thanks for reply@el676

According to the service manual (P 44), it's 80 Nm ***NOT*** 80 ft/lbs for the countershaft nut torque. That's 58 ft/lbs.

I will never buy these again

Mine is the 3.9L V6, but still has the same hose setup. Mine was leaking from the factory heat shrink clamps at the relief cap.

I put the batteries in and nothing happened. I tried 3 seta of new batteries. What am i doing wrong?

96 grams = 34 oz

$70 cad on Amazon with prime shipping nowadays lol

Good intentions, bad idea The fuel tank parts are plastic and designed to prevent pressure and pressuring up a plastic tank with compressed air and fuel is asking for trouble, now you’ve got fuel, air mixture looking for a source of ignition . You’ve just created a bomb. MT the fuel tank first

If you understood how a cooler works. It helps when you put cool things in there first. It lat forever at the cabin on one battery and a solar panel

I have a mobilcool. Fan does not turn in until you flick the switch to warm or cold

I can't help but laugh, the background noises are brilliant. Possible comedy sketch

Shoulda soldered it in horiz position,gravity is your friend!

Oh yeah, another thing for those that run these on the 20lb tanks- make sure to open the tank valve very slowly or else the internal valve will kick in and limit the output pressure of the gas.

Instructions unclear. I sprayed 3M adhesive in the thing instead of brake cleaner. Unit runs hot for some reason now. As far as the _gurgling sounds_ go, I searched around and it is a common issue with all of these heaters. I found a discussion on Reddit about it, and a few people had factory new units making that sound. I am writing this as my dual burner Buddy heater is gurgling away. A factory new-out-of-the-box heater should not gurgle. Most owners are thinking it is a pressure setting too low at the knob, so they use the heaters with it set in-between Medium-Lo. They light it and turn it past Low, until it stops the noise. It sounds just like a small breeze is blowing on the ceramic plate, no? Edit: I left my "o" out of something.

I need to reitterate something here to save all of you some greif, time and a little money, When you need to remove those large "C" clips DO NOT DO AS HE SUGGESTS TO USE ANY SCREWDRIVER OR TOOL TO PRY TO REMOVE THEM as you WILL 100% break them every time. They are fragile and will break very easily. They are also very very expensive beyond what they should be. What you do is stand in front of the water softener to give the softener a "bear hug" using both hands reaching behind and grasping the manifold and pulling it into the softener where you will feel the manifold move in very slightly as the water pressure has forced it "outward" that locks the "C" clips into it. You will pull it in just enough to release the clips and they will come out almost too easy and still be in perfect condition! Nuff said?

This was helpful. Thank you

I changed that and still no action with the windows

Only flashing thing I’m worried about is that check engine light 😮

My big buddy heater lasted for 12 years before it started gurgaling I'm going to clean it out tomorrow, bet I'll get at least another 10/12 years out of it

Is it just me, or whatever he's holding, looks transparent

Great video. Thanks for sharing. I managed to repair my softener.

HE DOESN'T HAVE CLUE WHAT THE CORRECT REPAIR IS

Runleader has a few models of meters. What is the model of the one that you use?

Here because my corn got stuck on Christmas day

16:47

show

Xt 500 ?

Voice overs are always fantastic especially when you're looking around

No yes sometimes somewhere

Recommended when you change a bulb you always change in pairs

My BIL is a mechanic and we could not get it on , which lead me to hear .

Wow its really good

Thank you!!! Your video is the only one that demonstrate the issue with turbine fix. I was ready to buy a new softener, as non of the other videos address this specific and common problem. I didn't relive water pressure, and broke the black clip. Only after I realized that water pressure was making it difficult to remove it. Thank you!

Thank you for sharing your knowledge

you're a cheat! Your filled up of vinegar wasnt in the same place at the end of your video! Boooo!!!

Breakcleaner is highly flammable folks

thanks for the info! will try this - before I dismantle it to get at the line.

Thank you so much for your video and showing us your alien key trick it was a huge help

I believe the pcv valve is incorporated under the top of the valve cover and you have to replace the valve cover. I'm speaking of a 2003 Saturn ion Quad coup with the 2.2 ecotec engine.

What magnetic plug did you get?

For clarification, all power inverters are sine wave, it means they produce 120volt AC (alternating household current). There are 2 types, Modified Sine Wave, good for anything except sensitive electronics like a laptop or some electric motors pretty much. True Sine Wave like he bought, which is much cleaner power & electronics safe. True Sine inverters are more expensive and heavier because there is more to it. Hope this clears up any confusion 🙂

HOW DO I MAKE THE PADS OR PADS STAY ON OR FLASHING?

Much respect to you, thank you

Hi, do you have a video on how to service the valve body, can i turn it by hand from the motor gear?

TRUMP WON

Yamaha xt250?

I have a water softener and I can’t free the valve unit from the canister. I’d like to change the beads in it but just can’t seem to free it up. Do you have any ideas as to maybe what I should do?

Thanks. I thought I could snake my way to the bulbs from the back but there’s a bunch of metal and stuff on the way. Saw your video and I had a gander around and saw the little screw for it. Thanks, I had forgotten how to change those bulbs.

😮 sick tail light

Put the tire back on turn tired by hand while turning the tensioner