Відео

the oil just has to be in between those two circles right?

Best vid I’ve seen ngl, was looking for where to Jack and Stuff too this is good

FYI: soapy water is your friend. Makes the entire process sooo much easier with a little placed around the rim.... Thank me later😊

Im late to the party but Do you jack the car from the rear or like normal as if you were doing a tire change ..

Were did u order from

Can you send the links plz for the parts ? I have the honda accord 2008 v6

Are there any filters to change

Thanks ! You give an idea on how to replace water pump ,,

thank you God bless. two codes in one video

this is too details😂 for me i just open up both side bumper and remove the clips above the front grill then just repalce the fog lamp no need to take out whole bumper becuz ltr u want to adjust back would be a problem for people that first time to do this

I have one but I hate the tube valve is buried. I'd rather get one with tubeless.

I can’t figure out what kind of wrench is used for dust trap cap? Not a allen wrench

Good job 👍

Thanks. I’m placing new solid rubber tires on - no more punctures

It's possible to connect the red wire in the fuse #19 instead of #33 ? (In the manual, it correspond to the auxiliary fog lights)

Is there a front differential in this hrv?

Thank you that was very short, concise and helpful

Thanks! This was a big help.

Very thorough, lots of care and attention. Great job

Dude thank you so much for taking the time to record this. I had an issue with replacing mine after my friend tried. I had to re-thread the axle by hand, but I finally got it on!! Now I'm having the issue of it not wanting to register the motor trying to accelerate

Going to do this, this weekend. I noticed my ac is not blowing cold. 😐 It has a green ish oil/ leak on that part. Do i have to do the receiver by the bumper

Where do I get that pump at.

Q

Certainly some people already told ya... THE MUSIC IS A NUISSANCE!!! especially the 1st one....

This video sucked 💯💯🙄🙄👎👎👎👎 I can't see how you put the tube and tire Back on, why is it fast forward

I have a Check Gas Cap warning on a 2009 Honda Accord. I replaced the gas cap and the code remains. Is this a possible repair for this issue?

"The "IN" side is the one on the condenser side" - big thank you for that piece of information

Thanks for the video. Enjoyed the music as well.

I can't get my back tire tube out to save my life.

Its a great pro tip to start with the fill plug because if you drain first and the fill plug is stuck your SOL

How do you put it back on

Tips to make it easy: boil hard tire for 15 min. Remove from pot, lube outside edge and inside of tire, one person presses tire onto wheel as much as they can, another person uses tire pry to slip last portion of tire onto wheel. Literally pops on in 5 seconds of work.

Thank you for this! Any idea if the 2022 hrv is the same process? My foglight cover was torn out and needs replaced

Put the new tires in the oven for a few minutes get them nice & warm & you will save yourself a half hr

You did not show how the end of the wire was fished from the engine compartment to the inside. You just showed how to remove the iside panel and plug the wire into the switch.

Thanks for the video I remove the batery I think its easier that way

The Allen key doesn’t work, you need HEX KEY, not Allen key!

There’s another video replacing the inner tube, way, way easier!

Hello, I have a 2011 Honda Pilot that was displaying P0496 (slightly different than your code) and P145C. We replaced the vapor canister purge valve and upon recheck of the codes, P0496 cleared on its own but P145C remains. Is it possible that it could take a few days for this code to clear? Mode 6 now shows a complete and pass for the purge flow monitor but the EVAP Monitor tests (4 of them- one 0.090" and three 0.020") show "Test not complete". LIVE mode showed the EVAP Vapor Pressure bouncing between -2.1 and 0.56 inH20 right after returning from a drive and parking the car on a flat surface in the garage. The reading prior to replacing the Vapor Purge Canister Valve was a solid -0.51 but no drive took place prior to reading. Should that pressure be bouncing around? Any suggestion would be helpful. Thank you

This video is amazing and I was following it until I couldn’t get the inner tube out because the Schrader valve was too long and wouldn’t come out. I saw in your video you made it seem like a piece of cake. Is there any specific you can tell me about taking the tube out? Would slime be an alternative to replacing a new tube and instead put the slime in the old tube to seek the air leak? Let me know 🙏

It’s hard to attach the electrical tire, any help?

broke my scooter doing this bullshit, worst fucking tutorial ever

have the same issue! Thank you so much for the video!!❤❤

Clean, well lighted video. Thank you!

Thanks man!

😃 muy bien muy bien👌 me gusto mucho como lo hiciste todo. Gracias por el video.👍🤓

Very detailed video..really appreciate your efforts

❤

What brand tools did you use? I like them and want to buy some.

Hey man so I know this video is a few years old but I just used this to change my pump! Went smoothly BUT the two 10mm bolts at 1:38 unfortunately broke into the old pump while removing them. I cannot find a replacement for them anywhere and I’ve tried some generic 10mm bolts thinking it would work but the pump keeps popping off from the pressure. Do you by chance know the part number or what I should be asking for? Lol