Відео

Heyy, do you know if I can put the two buttons from the R8 to my original RS3 8V 2018 Steering Wheel? Or was your Trimm different? Thanks!

What is the reason you do not use impact when you installed the bearing? Just try to make sure it is align good and do it slowly and able to feel it? Thanks for the video.

Duuuuude. You just saved me a SIGNIFICANT amount of money. Bought my 2020 RS3 a couple months ago and was told the pre sense restricted warning would be covered under the extended warranty.....but it turns out the car had been in an accident and the crash bar had been bent, which pushed the ACC sensor into the intercooler causing (cosmetic) intercooler damage. Because it was the result of an accident, the dealer said it wouldn't be covered by the extended warranty and wanted $4k+ to replace the intercooler, crash bar, ACC sensor, and perform the calibration. Instead I bent the ACC bracket back into shape and used your (very clear and concise) video to calibrate the sensor and clear the codes. ACC now works perfect with no codes or warnings!!! Thanks so much for taking the time to make this video!

Could we just remove some fuze instead of the battery?

Does the Drive select also work? Cause after wiring only the start stop has worked :(

Hey I replaced my oem grill and tried all 3 of the solutions but the static one says function unavailable and sets my code back on and the other one resetting it to 0.00 comes back on after 1 minute of driving any solution?

Where did you buy the Hot Rod?

Great video. Thank you.

Where did you get or loocking for this kit Start/Stop bottens becouse i want to install this in my car

Very good video, watched many videos on this removal, the best informative yet. Keep up making good videos !!AAAA++++

Hi, I want to open the ACC control unit in the app but i’m stuck with the same message “Control Unit not responding. Check Ignition and try again.” and then it boots me out from there, the car is on and everything else shows, i’ve reset the app and unplugged and turned on and off the car and it still hasn’t changed, any help? thanks

i wodnt recomend to use this oil on this nice car unles u chenging evry 500m. the oil u use is not made in germany, is made in france, that oil is grop 3 oil made by hydrocracking and is mineral oil, not syntetic. dont mind wath says on the can.is ilegal in germany to do inscription on the can syntetic on oils groupe 3, so they make in france no restriction.

Very useful solution, mark

Very professional install show！！！

It would be nice if it swivel side to side

If anybody want one buy direct from the company. Email them and ask for a promo 15% discount and they will send it to you. I paid $90. Plus tax

I have 2 cameras Azdome,but the display it is very small.

Goonzquad are hacks. They rig crap together to get it out the door.

Brilliant

Nice tool and good work 👍

thanks!

Could the start stop work with an Audi a3 or Audi Tt ?

Naa I painted 😅

great video! I was going to wait till spring to do this, after seeing the hub rental kit this is a breeze now ty ty deserves a sub!💪💪

How is possible to have this number of viewers in this video,this content is great.Greetings from Serbia.

locking split goes up?

can i use siggare light for this, i mean to heat that bolt and nut?

Cheers mate, Saved me today lol

Great video, gotta like that pressure bleeding system

Amazing! I already had the pro plan so you saved me some money, time and a headache.

Turning the car on and off like that is killing me

That was so satisfying. Fixed the problem and saved money. It would have been a nightmare without your video, especially the security code part. Thank you!

Best method up to date!!! thank you!

Thank you so much!

I just used a crowbar to remove the axle. No need to remove the strut. It was half the time as this video and I'm a DIYer

Does someone know for which cars that’s competitive? Thank you

Great video. But, I highly encourage anybody considering this product NOT to buy it. I purchased one, installed it, I get sound but I also get a "popping" sound when the unit heats up. It "pops" all sound cuts out for a few seconds and then it comes back on. The popping even happens with the unit off. Customer service was worse than horrible and they continued to discourage a return claiming it may takes months, get confiscated by customs, etc. DO NOT BUY.

Everytime i unlock the first clip the horn goes on🥲🫠

Bros yapping arround for 4 minutes.. till 4:16

Paying a deposit for the tool doesn't help me, if I had $400 I wasn't using I would buy a press. Thanks for the vid though, excellent instructions.

Don't you maybe want to sell the factory radio?

I followed your directions and solved a problem that was driving me crazy - thanks a bunch!

There are two part numbers for these. Which part number is for driver and passenger? Also is the driver side just as easy of a location?

Got the new axle installed today, only problem is now I need new knuckle too! turns out the collar around the ball joint was broken 😨 and my wheel was being held onto the control arm by just a bolt lol...

no packing the bearing with grease??

I can't seem to get my sound to work. My headunit powers on and works great. I double checked to make sure all my fiber optic wires are looped properly and it looks to be going straight from D2B decoder to the amp. With the canbus connector, my D2B wakeup wire is connected to the car's turquoise wire. Then opposite end the other two are properly connected. However there's just no sound. My amp fuse is fine too. Maybe my D2B decoder box is not getting power or broken? Can the headunit power on properly if the D2B box isn't powered?

Is there a way to do it with VCDS?

Very helpful thanks, quick question what letters of the part did you end up using from rental tool?

Do you know the seal numbers for both sides?

Where did you get the carbon fiber interior trim?