Відео

Hey on that drill you should be able to control speed it's got low // high speed switch and you can run it slow on trigger . I've got same tools but newer 2 Amp batteries the red ones

Great video! God Bless!

Listen to some more grandpas

Just stripped down my husqvarna 240e! Tried your tip worked a treat chainsaw runs as sweet as a nut😊it used to always cut out 😢 thanks for this excellent tip!

Great video bud, thanks!

It would be better to have the carburetor the right way up so it matched the saw. You have it upside down so L and R are reversed. Typical Grandpa mistake! Of course, if you turn each to snug then back off the same amount it won't matter--until you try to tune the idle speed... And what's that other big slotted screw for?

Bad quality

This 65 year old grandpa took your advise. I purchased the tool through your affiliate link. I grew up in a bucket truck. At 17 I was taking down Elm trees over mobile homes that died from the dutch elm disease. We used the old blue steel case Homelites. You could drop them from 50 feet and you may just bend a bar. I also walked in 2 feet of snow to the bus stop! lol.

You start with the choke & then with the fuel mixture. And you can get a whole set of the drivers @ hobofreight.

60 year old guy got it running like a champ! First time ever doing this. Tim me only 10 minutes after watching the video. You rock

Out/Rich - In/Lean

Thank you!

All I needed to know is to turn the screws all they way in and one and a quarter out. And that one is for low rpms and one is for high. The rest is not important and waste of time. This could've been 20s video. Still thanks a lot

Thought the letter t also on husqvarna chainsaw is for idling speed. My chainsaw chain is spinning on idle

Great job!

Great video! Thanks for your help!😊

Completely understand after watching just once. Thank you

Not a great explanation unfortunately. Watch Steve's small engine for one solid how to video on this.

Don't listen to this BS. I got three kids they know everything trust me. It's simple the first thing you didn't do is replace the carburetor. The second is don't fuck with the adjustments . You get a cheap china carb which most likely you will because the oe one is expensive and forget it you'll have constant problems. Get a factory rebuild kit super easy and cheap rebuild the original and don't touch any adjustments. You do it correctly and it'll start and run like brand new

U don't need those stupid tool just use a flathead dumbass

Your wideo is just as bad as other ones

I think I planted mine too early. It’s just now showing some leaves and it’s been a month

Thanks for the video 💕💕 Come back and give us an update 💯💯🙌🏼🙌🏼💕💕

Why does the saw have an idle speed screw?

Mine is variable speed… so idk what model you have but all 3 of my porter cables are variable speed like your milwaukee’s you showed

I needed the base line adjustments and you had them. Thanks! Excellent job!

Thank you

I really appreciate it! If anything can be messed up, I'll mess it up lol

Very food video, thanks, now my chainsaw IS running ok

Just get to the point

Exactly what I was looking for. Thanks.

No ay mejor prueba que en metal...de diferentes calibres

Hello my friands husqvarna 236 5200 chine carburator repair mu UA-cam Channel

Well done. I haven't worked on a saw in a while. Half blind as well....thanks for pointing out where idle adjustment screws were.

Great cheers dude.

The funny thing is Porter Cable and DeWalt are both owned by Black & Decker. I have been using Porter Cable for over 20 years, the 20v cordless tools are every bit as good as DeWalt. I will keep buying Porter Cable as long as they do not get cheap and cut corners in quality.

Thanks for pointing out the carb adjustment tool and the too lean setting. I loaned out one of my saws and it got cooked after the person who borrowed it set it too lean. An expensive lesson for me. Keep up the good work.

Know how,,,,been doing it 40 years😊😊😊😊

How about vs craftsman v20??

Thank you young man!

Well said & well done!! jj

The video is good, but why would you say , there are alot of videos out there and most of them are filmed by Grandpa's.." I'm not a grandpa, but I find that extremely offensive, its a cheap shot that gains you nothing other than making you look like a insensitive bastard. I would fix it if I were you.

what time of year did you plant it.nice video

the best video i fixt it 2 sequence

Thank you, no wasted words!

Just so people know, and this is important, make sure your air filter is clean first. Now, after backing screws back out 1 and 1/4 turns, and getting machine to idle properly, let it warm up for a full 5 minutes before attempting to adjust the high speed jet. If it is new adjust the high speed with just a tad of 4 stroking occurring, until it has broken in properly.

It would seem that you completely ignored the larger screw on the top with the slot. That's the one I started turning and it really didn't lower my idle. Now I don't know how to set that screw could you elaborate.

Outstanding. Simple and easy to remember. Tool ordered

Wow. Way to alienate people.

Does this take out the bog down when trigger is squeezed?