Відео

Page 76 of my VF150 manual has a NOTICE not to run the engine while attached to flush attachment. The water pump may be-damaged and severe damage from over-heating can result.

hi great video instructions, does it matter which red cable you connect to the switch posts?

Drill in reverse for a little ways then go in forwards

Maybe your brackets would look a little tidier if the back of the brackets were concealed behind the drilled holes secured using bolts with washers and locking nuts.

What bait to use in middle of May?

One tip… assemble everything on the drain plug side on the work bench, then feed the other end of the cable through the drain hole from the outside then secure to the transom.. that way your not doing everything on your head or on the ground underneath the motor…

👍Привет из России! А что в редукторе масло не сменил заодно? Тоже сразу хотел написать про ëмкость большего объëма, чтобы масло всë умещалось и не переставлять во время слива отработки. У нас на сливной пробке стоит металлическая шайба, еë не надо менять каждый раз, на масляном фильтре уже с завода нанесена смазка на резиноаой прокладке, мазать не надо, снял защитную плëнку и сразу установил. Если захочешь прибавить мощи, то этот мотор можно легко раскачать до 200 сил, путëм перепрошивки эбу, либо замена эбу от ф200. Думаю километров на 10 максимальная скорость прирастëт. В крейсерском режиме 3000-3500 оборотов расход топлива практически не изменится, ну разьве только на 0.5-1 литр. Ну на максималке естественно расход будет как у 200---72-75 литра в час если крутить 6000-6100 оборотов.

Seems to me , and this drives crazy on oil fills. They should have 1 line “ fill to here” easy and idiot proof. Why have a A and B ? In the manual does it say fill it to middle?

Good video but dang I’d b pissed all that oil on my new house slab.

You ran the engine without muffs??? Read the manual again. The garden hose you hooked just flushes the lower end. You ran the engine without water to the upper end. Don’t show people how to do things the wrong way!

How do you know what size switch is needed?

Bro yall found them stacked up like cord wood !! Great video

My two trolling motor batteries are in the bow, my cranking battery is in the back. I’d like to have a switch for both. Would it be simpler to have two separate switches? Or also a 3rd switch for my accessories?

Will they work on an 03’ zx225?

Cover the surface with blue painters tape first, then mark your holes, now you can drill the same slow way you did in the video.

Rocket City products are awesome and easy to install. The shipping is also fast.

Everything taste better outdoors

Good video!!!

Hey, I’ve got a question for duck commander can They build me a camo wood duck call

It's a nice fishing spot

Nice one

Nice video

Congrats! Beautiful smallmouth.

I have one

Congrats on your PB Smallmouth. You should take some of your products to nearby fishing tournaments.

Canned...aren't biscuits just eat the paper they came in it'll taste the same😂😂😂

Folks from the north take note. These are called biscuit makers not roll Makers.

Cooking CANNED biscuits. That's OK I reckon. But not real biscuits. Period. That is all.

Have you ever thought of making one longer straight bracket to hold 2 or 3 switches? I think it would make it more uniform and clean looking.

You need to take your friend fishing more. He’s pretty good…

Do you know how to remove the knob on Blue Sea System battery switch that has a removable knob for lock-out? Mine is a 6007 but the knob does not seem to just slide off. Thanks

Awesome!

Got two of them won’t go camping with out it either

I get all my fishing advice from this channel. Weather advice however, I’ll just keep looking…

God bless keep making vids.

I got one tonite, thanks for the fast shipping AND hardware.

I don’t think they can legally block off a section of the river like they have done. The land owner only owns to the waters edge. The river belongs to TVA and the State of Alabama.

My home town! Shoals Creek Bridge. To bad I’m stuck in Tennessee now days.

Wilson’s been rough here lately

Is that aluminum?

He is t “MAKING” biscuits, he’s COOKING biscuits. You can do this in a cast iron skillet.

This guy is stand up and his brackets are awesome.Nice doing business with you.

i just placed an order for the 90 degree bracket yesterday from the website, will I get a notification or tracking once the bracket is shipped out?

It’s very nice of you to include the hardware. Much luck with your company. ☘️

Remote drain valve? Cool! If I had a dollar for every time I forgot to put the plug in.. lol

Thank you for the video! Purchased your bracket and got mine installed today. I encourage anyone who wants a remote drain plug to go this route. Very simple and easy.

Those guys are tough down on Wheeler. I remember fishing a Heartland there years ago and having 18 lbs and guys came in with 25 lbs.

Are you the guy that has an eBay store? If so, we live very close and I need to pick your brain.

Biscuits and dead duck.

To prevent gellcoat from cracking, use a counter sink bit after your first hole drilled. This also will help prevent spyder cracks.