Відео

@@michelpetrus 4s 3300mah

@@rcrahul3657 Thank you.

@@SharphandXeno wow nice What's your power setup?

@@rcrahul3657 Motor: TP Power 2930 9D (3300kv) ESC: Hobbywing Platinum v4 60A Prop: Super S Carbon Speed 4.7x4.7 Battery: Tattu FunFly 4s 1550mAh 100C Servos: 3x KST X08H

I am from India, but not in India.

I don't see any problem landing on sand, except the paint on bottom maybe an issue. But if you apply some tape on the bottom it should be fine.

CG is 5mm in front of the screws (towards propeller) Elevator: 2.5mm up and down Aileron: 3-4mm, depends on your flying style, best is to have dual or triple rates configured

Thank you so much!!!

I don't remember clearly but I think I bought those BB Aluminium spinners from espiritmodel

Thanks for suggestion, will try if I get that prop. After the initial setup I changed the prop to 6x5.5 and the speed was massive.

@rcrahul3657 I'll typically run a 5.5 x 6.5 on 4s (2050 kv motor) and have gotten radar and doppler readings in the 175-180 mph range. On 6s I'll drop down to a 4.5 x 5.5 and typically get between 210-218 mph. The airframe (original carbon knife) has seen excess of 44G's so its definitely tough!

Can you please tell me what motor and esc set up you are using. I just ordered this plane. Thanks

​@@dadsrcwaffles HET 2W25 with 75A castle lite ESC, Similar to this HET, there is this Mega motor also 16/25/2 which can be used.

I havent, but its a very good idea... these planes are very efficient and extremely fast.. should really see how it works out. Dont have any spare DJI O3 though....

​@@rcrahul3657 How much is a plane like that usd price, and are any available in the usa. It seems like outside of usa has all the high end carbon fiber fast plane builds only .

Thanks. I was using a 75mah esc earlier, now I installed a 100A castle ESC on it to use a 6x5.5 prop. The speed is massive with this prop. Yet to test the 100A ESC though

Hahaha

Valid suggestion, however it's not always possible to stay away from propeller. So I try to ensure my hand is away from throttle, or the throttle cut switch is ON.

@@rcrahul3657 I can stay away from the propeller at all times

Hi, yes you need to scan a QR code given in the manual to enable WiFi. Secondly, WiFi can be connected only when you have only black and red wires connected to camera. It somehow doesn't work when yellow wire is connected to FC. So make another spare cable which can only give power and ground to the camera, only then the WiFi connection works.

QR code for WiFi can be found in this manual: manuals.plus/wp-content/uploads/2021/10/GP104691-GEPRC-Naked-GoPro-Hero-8-Full-Camera-Featured-Image-300x163.png

@@rcrahul3657 Hi there, thank you for your reply! I am still having trouble: I also got the Cinelog 25 and what i did was to remove the yellow cable from the connector that goes to the gopro. You mean I also have to unsolder the yellow cable on the fc in order to connect? Also, do I need to setup anything before trying this wifi thing? I've tried with the QR and it doesn't work for me :(

@@rcrahul3657 it worked finally!! :DDD thank you bro

No, its not true. I have been using the recording stop/start through my aux channel, and its working perfectly fine.

Sorry for late reply. 1) Camera has a switch which you can turn on for automatic power ON when you connect power lead. 2) you definitely need to stop recording before you remove power.

Not sure where is it set in GoPro.. However, FYI, this camera comes with GoPro labs firmware which can take QR code commands

Did you upgrade your firmware? The stock firmware should have a USER1 configured. I just checked that in my friend's CINELOG 25 too.

Nope

It's essentially a GoPro hero 8, so yes, it's the best 😃

I don't have any overheating problem. And the GoPro recording should always be stopped using a switch on your transmitter, else you will loose the clip.

That's right, the GEPRC website says it's a Bluetooth FC, however they don't have stock of that FC, So they shipped a standard F7 FC

This one is in ECP

@@rcrahul3657 wah nice..thanks bro

Hey Dan, this is in Port Dickson

@@rcrahul3657 beautiful ya

Tattu 650mah 4S

Yes. Same motor only

@@rcrahul3657 wow that's amazing I didn't think that motor would hold up my plane should be here shortly when it does adventure Time sure I'm going to upgrade it thank you very much for the info

@@rcman6895 All the best. But please upgrade your ESC to 100A first. As the original 60A ESC will not survive probably. And just to let you know, the Durafly stopped rating this plane for 6s, probably because they might have seen issues in the motor burning etc. Just to let you know so that you are aware of risking your motor 😊

@@rcrahul3657 okay I'll keep that in mind with the motor the ECM I have plan on replacing anyway okay well thank you very much for the info

Thanks bro. Happy flying for you too.

Betafpv 850mah 3s battery, and stock props. 2" 4 bladed.

@@rcrahul3657 thanks! I thinking in buy one :)

@@rcrahul3657 thanks! I thinking in buy one :)