Відео

How to fix a ruko remote

My existing light fixture has a ground, a white and a red. It looked like the short black wire had been capped off. It wasn't a motion sensor light or anything. What should I connect to what?

Can this be done without a power drill?

You have a very good way of explaining and i thank you for that.. but honestly, this earth need simple things.. heating +/- and ac +/- .. i dont need wake leave away sleep.. im too old.. i dont remember passwords.. it is not senior citizen friendly..

Thank you for taking the time to make this video.

If doing this in an unfinished basement, should this be done before studs are installed? If so, how do you fasten the studs to the floor?

A comment for the algorithm.

Thanks so much! I was just about to buy a coax tester for this purpose, only to probably have it sit on my workbench forever after that! Excellent information!

Thank you so much. It was very helpful 👍

WASTE OF GODDAMN MONEY

Good, but would have liked to have seen the result.

nice. direct and to the point. i dont know how you can make a video without showing us your face for 10 minutes! lol.

A little compressed air wouldn't hurt. Also, some bleach (4% diluted) or hydrogen peroxide poured in there & left to sit for 15-30 min. should kill most of the mold. Concrobium Mold Control is a product you can get at hardware stores or online that mostly consists of Hydrogen Peroxide and will do the job. Brush away whatever you can first.

Brilliant 😮

Thanks, this is what I was looking for: no stories, no jokes, clear demonstration, a little jazz in the backround

Can these be used with natural gas

Great video, accurate and to the point 👍

Ferry Canyon

Thank you TRD! this is the first I ever attempted this and it worked thanks again for the vid!

Straight forward video, no BS 👍

Madisen Lodge

Bro your method of using bit #1 to drill and bit #2 to extract worked perfectly. Thanks for clearing my headache dude

Thank you! You saved me so much time!

Genius

This is an incredible hack. I was just shopping for a coax cable tester when I saw this. Thanks!!!

Leuschke Run

Henriette Plain

Miller Lock

Finally, a concise instructive video for this tool.

It would have been nice if you showed it yp close. I couldn't tell which side was which.

Zemlak Spurs

47894 Francisca Plaza

Danke!

Can I use the end of a crimper tool to do cinch clamps? Week one student, so excuse my ignorance

Are you using PEXA or PEXP?

I'm sorry to say that this video did not help me with the time besides finding the general button that has to do with time. You must press so that you see day, time and schedule. Then you must press and hold. Then you have to keep arrowing up or down to change the minutes and keep going until 60 minutes to get to the next hour. It's really quite a pain in the ass but at least there's a solution.

I have this tool. For the price I like it. It is clumsy with the size and 2 handed use along with me being very much a novice. Knowing what I do now after using it I would still buy it again. As for the pipe cutter. I found it decent. I have a smaller version than the one you got from ace. That i got from Ace. I like the one from that came with the clamp better. Neither cuts a great straight line but it cut better than the Ace one.

What if I don’t care about temperature at all? I want my fan to turn on and circulate the cold air and moisture out of my basement. I want to program it in, to cycle the air about 3 times per day for about 1 hour each. Only other option is to leave it one forever or remember to go to the thermostat 6 times per day to turn it on and off manually

This video is a money and time saver thanks!!!

In spite of all of the negative comments here about this product, I just purchased it. It's $25 and Amazon has a great return policy. Also it has over 10k reviews and 4.5 Stars rating, so I'll give it a try. Thanks for the review.

Thank you for the much needed tip about sizing up when extracting. What I also did was to slightly turn it sideways (instead of keeping it straight up) when extracting to try and catch the grove and that’s what magically pulled up the stubborn stripped nail. Again, thank you!

Will it work for stripped Allen keys?

Thanks for the help!

Thanks Bud👏‼️

I use the Ryobi elctric tool. Got a refurbished one for a little over $80 pre tax from Ryobi deals finders. They sell new ones for $99 but are always out of stock. And just to clarify, the clamp has to be between 1/8th and 1/4 inch from the fitting.

Thanks

I tried it just like you said and it doesn't work. I've tried it with two screws today and could get neither one out. The bit doesn't seem hard enough to even drill a hole. They are just regular drywall screws, they shouldn't be that hard.

OMG that lil azz remote needs a tiny flat head screw-driver to take it apart. All I had were too big to work with so I just used the handle of a screwdriver and hit the remote in that area several times and it's working now. It's a dam shame how crappy they make things now days. Roku needs to make a remote that's not Barbie & Ken doll size. If you set it down and go get a snack or blink u eyes the dam thing gets lost 😀

Will this work for the 18v ryobi?

I think I'd prefer to use a male F-connector, short it, then cover it with electrical tape. Costs less than a dollar.